Will Changing Lanes Over Solid Lines Definitely Be Captured?

1 Answers
OLucia
07/24/25 3:55am
When a vehicle changes lanes over solid lines at an intersection, it is highly likely to be captured because the cameras operate at a very high frequency. Changing lanes over solid lines is a violation of traffic prohibition signs and is punishable by a three-point deduction and a fine. Continuous lane changes can be determined by the vehicle's turn signals. For example, before changing lanes, the vehicle will signal in advance. The direction of the turn signal indicates the intended lane change direction. After signaling, the driver must check the opposing lane and rear vehicles before proceeding with the lane change. Deceleration markings are divided into longitudinal deceleration lines and transverse deceleration lines, usually located near toll booths, exit ramps, or other areas requiring vehicle deceleration, marked with white dashed lines. Longitudinal deceleration lines typically consist of a series of diamond-shaped dashed lines parallel to the lane dividers, often placed at bridge approaches, exits, or curves. Their primary function is to create a visual narrowing effect, inducing a sense of pressure that prompts drivers to slow down automatically in designated areas. The photo enforcement system for lane changes over solid lines uses ground-pressure magnetic induction coils. The principle of photo capture is as follows: When the front wheels of the vehicle pass over the induction coil on the ground, the system captures the first photo electronically; when the rear wheels pass over the induction coil, the second photo is taken; and when the vehicle crosses the intersection and passes over the induction coil on the opposite side, the third photo is captured. The system for capturing lane changes over solid lines operates 24/7, and the images and related data are retained for one week. Minor lane changes over solid lines that do not result in major safety incidents are usually not captured. Additionally, temporary license plates used on new vehicles are often difficult to capture clearly in electronic violation photos due to material issues.
Was this review help?
5
3
Share
More Forum Discussions

How to Resolve EPC Light on Dashboard?

The reasons and solutions for the EPC light appearing on the car are as follows: 1. False Alarm: When the EPC light comes on, the owner can first try turning off and restarting the engine to see if the EPC light remains on. If it turns off, it indicates no significant issue, just a false alarm affecting the EPC light. If the EPC light stays on or frequently comes on, it suggests a fault with the electronic throttle. 2. Substandard Fuel: Ensure the intake system is fault-free, use fuel that meets standards, and clean the throttle body. 3. ECU Fault: Reflash the ECU-related data.
16
2
Share

How to Remove the Cabin Air Filter of Chevrolet Equinox?

Steps to remove and replace the cabin air filter of Chevrolet Equinox: 1. Locate a black plastic panel above the passenger footwell area, which has two retractable clips. Press and release them to remove the panel. 2. Disconnect the negative battery terminal, then remove the body control module and its mounting bracket. 3. Unscrew the four fasteners on the panel near the passenger's left footrest area for filter access. Below is relevant information about cabin air filters: 1. High-efficiency filters can effectively trap particulate matter while purifying air and eliminating TVOC, benzene, phenol, ammonia, formaldehyde, xylene, styrene and other organic gases, making them ideal materials for premium vehicle HVAC systems. 2. These filters purify incoming air by removing contaminants including micro-particles, pollen, bacteria, industrial exhaust and dust. They protect HVAC components from damage while ensuring clean cabin air for occupant health and preventing windshield fogging.
15
3
Share

What Are the Reasons for Severe Cabin Bouncing?

Here are the reasons for severe cabin bouncing: 1. Poor tire balance: If you notice slight shaking or deviation of the car body while driving, it is usually caused by tire issues. The owner should promptly perform a four-wheel alignment and dynamic balance. If the vehicle does not pull to one side, just performing a tire dynamic balance will suffice. 2. Deformed steel rims: This condition usually occurs in older vehicles. The owner should take the car to a professional repair shop for inspection. Generally, when replacing new tires or steel rims, a tire balance should be performed. Otherwise, an uneven weight distribution can easily cause the steering wheel to shake. 3. Deformed or unbalanced drive shaft: This is usually caused by a deformed or unbalanced drive shaft, and it is more common in vehicles that have had chassis collisions.
5
1
Share

What are the impacts of converting a car to gas and then back to gasoline?

The impact of converting a car to gas and then back to gasoline is that the damaged pistons and piston rings in the cylinder cannot be restored to their previous performance. Below are specific maintenance tips for gasoline-to-gas converted vehicles: 1. Equipment maintenance: Regular maintenance of the conversion equipment is necessary. Due to the special properties of the fuel used, a comprehensive leak test should be conducted on the gas tank every two weeks. 2. Driving habits: Before driving each day, in addition to the checks specified in the original car manual, inspect all pipelines for cracks or oil leaks. If the vehicle is to be parked for a short period, the main power switch and the CNG cylinder valve must be closed. Additionally, ensure that fire extinguishing equipment is available inside the vehicle during daily driving. If the vehicle is to be parked for an extended period, the CNG should be completely used up. It is prohibited to repair the gas supply system in enclosed garages or workshops.
4
5
Share

Where are the accelerator, clutch, and brake pedals located in a car?

In a car, the clutch pedal is on the left, the brake pedal is in the middle, and the accelerator pedal is on the right. Here is some additional information about cars: 1. Function of the clutch: It can increase the driving force of the car, ensuring smooth and normal starting; facilitates gear shifting, thereby reducing impact between gears; prevents overload of the transmission system; reduces torsional vibration impact and extends the lifespan of transmission gears. 2. Function of the brake: To slow down the speed of the car and bring it to a stop. 3. Function of the accelerator: By controlling the amount of pedal depression, it regulates the throttle opening of the engine, controls the air intake, and the computer controls the fuel amount, thereby controlling the engine's speed.
18
4
Share

How to Match the Sunroof on the LaCrosse?

The matching method for the LaCrosse sunroof is: 1. Press and hold the switch to open the sunroof; 2. Continue holding the switch for about 3 seconds; 3. Then close the sunroof, and after it is fully closed, press and hold the switch again for about 3 seconds. The LaCrosse is a mid-size 4-door, 5-seater sedan under SAIC-GM-Buick, with body dimensions of 5026mm in length, 1866mm in width, and 1459mm in height, a wheelbase of 2905mm, and a fuel tank capacity of 55 liters. The LaCrosse is equipped with a 2.0T turbocharged engine, delivering a maximum power of 174 kW at 5000 rpm and a peak torque of 250 Nm between 1700 to 4000 rpm, paired with a 9-speed automatic transmission.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.