Will a Car Get Damaged from Daily Sun Exposure?

1 Answers
ColinFitz
07/30/25 8:26am
Daily prolonged exposure to intense sunlight can cause problems for a car, as high temperatures directly accelerate the aging of rubber components, paint fading, and the deterioration or damage of electronic components inside the vehicle. Accelerated Aging of Rubber Components: Under direct sunlight, the rubber parts of a vehicle can develop cracks and deteriorate due to UV radiation, leading to reduced braking efficiency, poor traction, increased fuel consumption, and decreased power. Tires are particularly affected, with their lifespan significantly shortened. Paint Fading: The car's paint, being the largest surface area exposed to sunlight, undergoes oxidation reactions between metal ions in the paint and oxygen ions in the air when exposed to prolonged sun exposure. For example, white cars may turn pale yellow over time, while darker-colored cars gradually lose their luster and vibrancy. In severe cases, the paint may even peel off. Aging or Damage to Electronic Components: Under intense sun exposure, the interior temperature of a car can soar above 60 degrees Celsius. Prolonged exposure to such high temperatures accelerates the aging and failure rate of electronic components inside the vehicle. For instance, most sensors experience a significantly reduced lifespan in high-temperature environments. Additionally, leaving hazardous items like sunglasses or lighters inside the car can pose serious safety risks.
Was this review help?
15
2
Share
More Forum Discussions

What are the types of rear axle models?

Micro truck rear axle models are generally 121, 130, 140. Light truck and dump truck rear axle models include 145, 1058, 1069, 1070, 1080, 1081, 1090, 153, 457. The last two are specifically for heavy trucks, and among these models, there are extended, shortened, and standard versions. Definitions of various trucks: Micro truck: A micro truck is a type of truck. According to China's motor vehicle specifications, "micro" is defined as: vehicle length ≤ 3.5m, total mass ≤ 1800kg. Light truck: Light trucks refer to N1 category vehicles in the N-class truck classification with a maximum design total mass not exceeding 3.5 tons. Dump truck: A dump truck is a vehicle that unloads cargo by hydraulic or mechanical lifting, also known as a tipper. It consists of components such as the vehicle chassis, hydraulic lifting mechanism, cargo compartment, and power take-off device. Heavy truck: Heavy truck is the abbreviation for heavy-duty truck. This is a colloquial, traditional, and informal term for heavy-duty trucks and semi-trailer tractors, including various specialized vehicles seen on highways (water trucks, fire trucks, road sweepers, tankers, mixers, etc.), dump trucks (earth-moving trucks, all equipped with lifters), trucks (for transporting goods, including livestock), and some less common off-road vehicles (mostly military).
9
2
Share

What Causes a Motorcycle Gear to Get Stuck and Unable to Be Pressed Down?

The issue of a motorcycle gear getting stuck and unable to be pressed down is likely due to incomplete clutch disengagement. This can cause difficulty in shifting gears, and when the clutch is pulled, it fails to completely cut off the power connection, resulting in the motorcycle still having a tendency to move. It is necessary to check whether the clutch cable travel is too large or if the clutch push rod is stuck. Below is an introduction to mopeds: Definition and Standards of Mopeds: Regardless of the driving method, a moped is defined as a motorcycle with a maximum design speed not exceeding 50km/h. If powered by an internal combustion engine, its displacement must not exceed 50ml. If electrically driven, the motor's rated output power must not exceed 4KW in total. Requirements for Riding a Moped: To ride a moped, one must be at least 16 years old, with a height of 1.45 meters or above, vision of 0.7 or above (or corrected to 0.7 or above), no red-green color blindness, normal hearing, and no physical defects or diseases that hinder safe driving. After passing a medical examination and tests on traffic rules and driving skills administered by the public security authorities, a moped driving license will be issued. For licensed mopeds, a medical examination is required every two years, and those who fail are not allowed to continue riding.
16
1
Share

What Causes a Scooter to Jerk When Accelerating?

Scooter jerking when accelerating is often due to the vehicle's half-shaft experiencing bending, twisting, breaking, or spline wear and misalignment under long-term torsional fatigue and impact forces. This can cause rhythmic shaking of the vehicle's front end when accelerating within a certain speed range, with the shaking disappearing or reducing upon releasing the throttle. Solution: Regularly replace the half-shaft. Working Principle of Scooter Transmission System: The transmission mechanism of a scooter operates through two pulley disks connected by a drive belt. At idle speed, the pulley disks and drive belt remain loose, unable to propel the motorcycle forward. As engine speed increases, centrifugal force causes the pulley disks to engage more tightly with the belt, changing the gear ratio. Higher engine speeds result in greater gear ratio changes, leading to faster vehicle speeds. Maintenance of Scooter Transmission System: After covering the transmission case, the airflow guide on the front pulley disk creates a directional air flow inside the transmission case. This serves two purposes: cooling the transmission system and expelling dust generated during operation to prevent excessive wear of internal components.
12
5
Share

How to Remove the Exterior Rearview Mirror Assembly?

Steps for removing the exterior rearview mirror assembly: 1. Prepare a socket wrench or screwdriver. The interior trim panel corresponding to the exterior rearview mirror can be pried off directly or pushed open with an object. Then, use the socket wrench or a screwdriver of the corresponding size to unscrew the nut. 2. Locate the mirror integration box. The rearview mirror has dedicated wiring, and the integration box is usually hidden inside the door panel. Therefore, pulling the wiring upward by hand can help locate the integration box. 3. Reinstallation method. Following the above steps completes the removal of the exterior rearview mirror assembly. For reinstallation, first place the exterior rearview mirror back in position, then tighten the corresponding nut using the socket wrench or screwdriver. After tightening, reconnect the integration box to complete the entire removal and installation process.
7
1
Share

What procedures are required for motorcycle inspection?

For motorcycle inspection, you need to prepare the original and photocopy of the motorcycle's registration certificate, personal ID card, and the original compulsory traffic insurance policy. Ensure that any previous traffic violation records are settled before the annual motorcycle inspection. After confirming there are no outstanding violations, take the relevant documents to the insurance company to verify the insurance policy. Then, you can proceed to the motor vehicle inspection site with the above documents for the inspection. The following are the contents of motor vehicle annual inspection: Document check: Verify if the vehicle's user manual, certificate of conformity (for imported vehicles, the commodity inspection certificate), and the factory inspection marks on the vehicle body are complete. Measurement of motor vehicle dimensions: Measure the internal and external dimensions, wheelbase, and axle track of the motor vehicle. Specific measurements include vehicle length, width, height, cargo compartment sideboard height and area, wheelbase, and axle track. Completion of alteration registration form: Conduct the inspection item by item according to technical standards. If passed, fill out the "Initial Inspection and Alteration Registration Form for Motor Vehicles" and enter the curb weight, load capacity, passenger capacity, and driver's compartment seating capacity as specified by the manufacturer.
11
1
Share

What is the function of the carburetor needle height?

The function of the carburetor needle height is to form an annular main nozzle with the carburetor main jet, delivering a certain amount of combustible air-fuel mixture to the cylinder head. Below are the related details: Needle clip adjustment upwards: When the needle clip is adjusted upwards, the needle position moves relatively downward, and the annular main nozzle of the carburetor also decreases. At this time, the combustible air-fuel mixture delivered to the cylinder head through the main nozzle becomes leaner. Conversely, a richer combustible air-fuel mixture is obtained. Needle position adjustment: Adjusting the needle position will directly cause a noticeable change in the carburetor's air-fuel mixture ratio. Although it may start smoothly at different settings, under normal driving conditions, it can lead to various engine issues, such as stalling when accelerating, incomplete combustion in the cylinder head, black smoke from the exhaust pipe, and a series of other problems.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.