Why Won't My Baojun 730 Start?

1 Answers
LaAnderson
07/29/25 10:07pm
Baojun 730 failing to start may be caused by a depleted vehicle battery or an empty fuel tank. Specific reasons: Failure to start could be due to a discharged vehicle battery, lack of fuel in the tank, issues with the engine intake tract, or frozen exhaust pipes - all of which can prevent the car from starting. Solutions: When encountering starting issues, first check the vehicle's battery. In most cases, excessive battery depletion is the primary cause of startup failure. During annual vehicle maintenance, the battery should be tested to evaluate its wear level. If battery wear reaches 90%, it's necessary to replace it with a new one to prevent operational failures.
Was this review help?
14
5
Share
More Forum Discussions

At what age can I get a B2 driver's license?

To apply for a B2 driver's license, the age requirement is between 21 and 50 years old. Below are the specific details about the B2 driver's license: 1. Permitted Vehicle Types: The B2 license allows driving medium and heavy-duty trucks or specialized operation vehicles, as well as small cars, small automatic transmission cars, low-speed trucks, three-wheeled cars, and wheeled self-propelled machinery. The B2 license does not permit driving passenger buses or tow trucks. To drive a tow truck, an A2 license is required, while a B1 license is needed for driving passenger buses. If you wish to drive both passenger buses and trucks, you need to apply for either a B1 or A2 license. 2. Application Method: The B2 driver's license can be applied for when initially obtaining a driver's license or through upgrading from a lower-level license. Regardless of the method, you need to submit an application to the local vehicle management office in your registered residence, then undergo a medical examination as required, and proceed to a driving school for training and testing.
18
3
Share

Which wire on the national standard controller is the speed limit wire?

The speed limit wires on the national standard controller are two white plug-in wires. Composition of the national standard controller: A controller includes various wires such as the ignition lock wire, three-speed gear shift wire, self-learning wire, reverse wire, cruise control wire, high-level brake wire, low-level brake wire, motor Hall sensor wire, throttle wire, anti-theft alarm wire, alarm power wire, motor phase wire, speedometer signal wire, etc. Unplugging the connector of the speed limit wire can remove the vehicle's speed limit, restoring the vehicle's power to its factory state. Precautions for using the controller: Different electric vehicles have different wire configurations, and the colors of the wires may vary. To avoid confusion and ensure correct modifications to the electric vehicle controller, it is essential to seek professional assistance. This ensures that the wiring is done correctly and prevents unnecessary faults caused by incorrect operations.
3
2
Share

What is the speed limit for 92v tires?

92v tires have a maximum speed limit of 240km/h. Meaning of 92v: 92 is the load index, and v is the speed rating. The load index indicates the maximum weight the tire can bear; specifically, 92 means the tire can bear a maximum weight of 630 kilograms. Generally, the higher the speed rating of a tire, the stronger its grip, but it also tends to wear out more easily. Typically, v-rated tires wear out faster than h-rated tires. Introduction to tires: Tires are a crucial component of a car, affecting both driving stability and safety. There is a lot of important information on the sidewall of a tire, such as the load index, speed rating, production date, recommended tire pressure, size specifications, etc. During regular use, it's important to frequently check the tire pressure and inspect the tire surface for any signs of damage.
1
1
Share

How to Attach the Compulsory Insurance Sticker?

Compulsory insurance stickers should be affixed as follows: According to relevant regulations, the compulsory traffic insurance sticker must be attached to the upper right corner of the front windshield. Relevant information about compulsory insurance is as follows: 1. Introduction: The full name of compulsory insurance is "Compulsory Motor Vehicle Traffic Accident Liability Insurance." It is a mandatory liability insurance where the insurance company compensates for personal injuries, deaths, and property losses (excluding the vehicle's occupants and the insured) caused by road traffic accidents involving the insured vehicle, within the liability limits. 2. Necessity: Compulsory insurance ensures compensation for victims of motor vehicle traffic accidents and promotes road traffic safety. It provides timely and basic protection for traffic accident victims.
18
3
Share

Where is the VIN located on the new Cayenne?

The VIN of the new Cayenne can be found on the engine hood, specifically in the lower left corner inside the windshield. VIN structure: There are mainly two formats for Vehicle Identification Numbers. The first is the ISO3779 standard adopted by the European Union, while the second standard is primarily used in North America, which is more stringent than the first but remains compatible with it. VIN plate location: The plate should be fixed on the door hinge pillar, door lock pillar, or one of the door edge pillars connected to the door lock pillar, near the driver's seat. If such a location is not available, it should be fixed on the left side of the dashboard. If that is also not possible, it should be fixed on the inner side of the door near the driver's seat. If none of the above locations can be used, a written application must be submitted to NHTSA.
8
0
Share

What are the components of a braking system?

Braking systems primarily consist of four parts: the energy supply device, control device, transmission device, and brake. Functions of the braking system: The main functions of the braking system are to decelerate or even stop a moving vehicle, maintain a stable speed for a vehicle going downhill, and keep a stationary vehicle from moving. It is a series of specialized devices designed to forcibly reduce the vehicle's speed. Structure of a typical braking system: It mainly consists of wheel brakes and hydraulic or pneumatic transmission mechanisms. The wheel brake is primarily composed of rotating parts, fixed parts, and an adjustment mechanism. The rotating part is the brake drum; the fixed parts include the brake shoe and brake backing plate; the adjustment mechanism consists of an eccentric support pin and an adjustment cam used to adjust the shoe-to-drum clearance. The hydraulic brake transmission mechanism mainly includes the brake pedal, push rod, master cylinder, wheel cylinder, and piping. The pneumatic brake transmission mechanism mainly consists of the brake pedal, push rod, brake valve, air dryer, four-circuit protection valve, brake chamber, and piping.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.