Why was the Shuai Ke discontinued?

1 Answers
EvaLee
07/29/25 6:56pm
This model has not been discontinued. The Shuai Ke has not seen any facelift models for a long time, and the currently available Shuai Ke is the 2016 model. Below are the relevant details: Overview: The Shuai Ke is an MPV model, equipped with two engines—a 1.5L naturally aspirated engine and a 1.6L naturally aspirated engine. 1.5L naturally aspirated engine: It delivers 102 horsepower and a maximum torque of 132 Nm. The engine's maximum power is achieved at 6000 rpm, and the maximum torque is available between 4000 to 4600 rpm. This engine features multi-point fuel injection technology and uses an aluminum cylinder head with a cast iron block. 1.6L naturally aspirated engine: The HR16 engine produces 113 horsepower and a maximum torque of 150 Nm. The engine's maximum power is achieved at 5200 rpm, and the maximum torque is available at 4400 rpm. This engine also features multi-point fuel injection technology and uses an aluminum cylinder head and block.
Was this review help?
8
4
Share
More Forum Discussions

What Causes Airbags Not to Deploy?

Airbags may not deploy because the conditions for airbag deployment are not met. Necessary conditions for airbag deployment: 1. Vehicle speed is generally above 50 km/h, but the key factor is the acceleration at the moment of collision. In national certification tests, the instantaneous acceleration during collision is approximately -40g. 2. Frontal impact: The angle of impact must be within approximately 60° from the front. 3. Collision object: Rigid walls or obstacles. Airbags will not deploy when a car collides with soft objects at 80 km/h. 4. Deployment time: Within tens of milliseconds after the collision occurs.
12
5
Share

What is the Principle of Ultrasonic Sensors?

Ultrasonic sensors work on the following principles: 1. An ultrasonic sensor consists of a transmitting sensor (or wave transmitter), a receiving sensor (or wave receiver), a control unit, and a power supply. 2. The transmitter sensor is composed of a transmitter and a transducer using a ceramic vibrator with a diameter of about 15mm. The transducer converts the electrical vibration energy of the ceramic vibrator into ultrasonic energy and radiates it into the air. 3. The receiving sensor consists of a ceramic vibrator transducer and an amplifier circuit. The transducer receives the wave, generates mechanical vibrations, converts them into electrical energy, and outputs it as the sensor receiver, thereby detecting the transmitted ultrasound. 4. In practical applications, the ceramic vibrator used as a transmitting sensor can also be used as the ceramic vibrator for the receiving sensor. The control unit mainly controls the pulse chain frequency, duty cycle, sparse modulation, counting, and detection distance of the transmitter.
17
3
Share

Does BYD dmi have a transmission?

BYD dmi has a transmission. Here is some information about BYD: 1. BYD Company Limited, headquartered in Shenzhen, Guangdong, China, is a high-tech private enterprise with three major industrial groups: IT, automobiles, and new energy. 2. BYD has established nine production bases in Guangdong, Beijing, Shaanxi, Shanghai, Tianjin, and other locations, covering a total area of nearly 7 million square meters. The company also has subsidiaries or offices in the United States, Europe, Japan, South Korea, India, as well as in Taiwan and Hong Kong regions of China, with a total workforce of nearly 200,000 employees.
16
2
Share

What are the reasons for the high water temperature in Dongfeng Fengguang 580?

The reasons for the high water temperature in Dongfeng Fengguang 580 are as follows: 1. Severe leakage in the cooling system or insufficient water volume: Overheating caused by insufficient coolant due to severe leakage in the cooling system can be diagnosed directly through observation and the fault can be eliminated smoothly. There are two reasons for engine overheating due to the cooling system's water capacity being lower than the standard capacity: (1) Excessive scale: This mainly occurs in engines that have used water as coolant for a long time. As the mileage increases, the scale on the water jacket walls and inside the radiator tubes in contact with the cooling water will gradually thicken, especially in high-temperature areas, severely affecting the radiator's heat dissipation efficiency. The heat generated by the engine's operation becomes difficult to dissipate in time, leading to overheating. (2) Radiator clogged by debris: The radiator may be filled with sludge, scale, cotton yarn, and other debris, blocking many core tubes and causing the radiator's actual capacity to be far below the standard capacity. After removing the debris from the engine, the overheating phenomenon will disappear. 2. Abnormal water pump operation: If the discharge indicator or charging light comes on while driving and the engine overheats at the same time, it is usually due to a broken water pump belt. If the water pump belt is in good technical condition and has proper tension, then consider whether the water pump has failed, interrupting the circulation of cooling water and causing engine overheating. 3. Thermostat failure: This fault is mainly manifested by the thermostat's main valve not opening fully or the thermostat being stuck between large and small cycles. Other issues include aging of the thermostat and poor sealing causing leakage of the expansion body. These faults can all lead to poor circulation of cooling water in the large cycle after the engine temperature rises, resulting in engine overheating.
13
1
Share

How to Tell if a Car is Refurbished?

Here are methods to identify a refurbished car: 1. When purchasing a car, choose an authorized 4S dealership to ensure the vehicle's source is reliable, minimizing the chance of getting a refurbished car. 2. Check the car's certificate of conformity, manufacturing date, odometer reading, and VIN (Vehicle Identification Number) for any irregularities or signs of tampering. If found, be cautious as it might indicate a refurbished car. Note that the odometer value should only be taken as a reference. 3. Inspect the brake discs. Normal brake pads should appear slightly shiny, while overly smooth ones suggest excessive wear from frequent use, raising concerns about the car being refurbished. 4. Examine the engine nameplate for the production date. If the date is significantly old, it may not be a best-selling model. A gap of several years warrants checking for refurbishment. 5. Observe the engine's mounting screws. Scratches or signs of removal indicate repairs, suggesting the car isn't new or at least has been repaired. 6. Inspect the car's exterior. Uneven paint spots or color inconsistencies likely point to a refurbished car, as new cars wouldn't have such issues.
15
3
Share

Why is the steering wheel on the left side?

China's traffic regulations require driving on the right side of the road. If the steering wheel were on the right side, the driver would have difficulty seeing the traffic and road conditions behind them, hence it must be positioned on the left. Additional information about road traffic directions is as follows: 1. The direction of road traffic is an important aspect of traffic regulations worldwide, specifying which side of the road vehicles should drive on to prevent confusion and accidents. 2. Road traffic directions can be divided into two categories: left-hand traffic and right-hand traffic. 34% of countries drive on the left side, while 66% drive on the right side. 3. The side of the road vehicles drive on depends on long-established traffic rules, which have led to more detailed and strict road traffic regulations. Many countries have legally defined the direction of vehicle traffic.
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.