Why Should Brake Fluid Be Replaced?

1 Answers
Russell
07/25/25 2:08am
Failure to replace brake fluid for an extended period can lead to its deterioration, which may result in brake system failure. Generally, brake fluid should be replaced every 2 years or approximately 60,000 kilometers. The following points should be noted during the use and replacement of brake fluid: 1. If mineral oil is mixed into the brake fluid, the entire brake fluid should be replaced. For example, if gasoline, diesel, or engine oil accidentally mixes into a brake system that uses synthetic brake fluid, the incompatibility of the fluids may significantly reduce braking effectiveness. 2. If water is mixed into or absorbed by the brake fluid, or if impurities or sediments are found in the brake fluid, do not proceed with the injection. In such cases, the brake fluid should be replaced or carefully filtered; otherwise, insufficient brake pressure may occur, affecting braking performance. 3. For vehicles equipped with a brake fluid level warning device, always monitor whether the warning indicator light is flashing and whether the warning sensor is functioning properly. If the brake fluid level is low, it should be replenished promptly. The stored brake fluid should be maintained between the marked minimum and maximum capacity lines. 4. During normal driving, if the braking force becomes inconsistent (sometimes light, sometimes heavy), the brake fluid should be replaced. Before replacement, the brake system should be thoroughly cleaned with alcohol.
Was this review help?
12
0
Share
More Forum Discussions

What Causes the Santana's Air Conditioning Not to Cool?

Here are the reasons why the Santana's air conditioning is not cooling: 1. Lack of refrigerant: The loss of refrigerant is mainly due to leakage. If the car's air conditioning performance is poor, and it becomes poor again after refilling the refrigerant, then attention should be paid. 2. Air in the air conditioning system: Once air enters the air conditioning system, it will cause excessive pressure in the refrigerant pipes, and poor refrigerant circulation will also lead to insufficient cooling. This type of fault is mainly due to the deterioration of the sealing of the refrigeration system. 3. Damage to the air conditioning compressor, throttle valve, or expansion valve: There is a saying in the air conditioning compressor circle: 'Low pressure high, high pressure low, replace the compressor.' The probability of damage to the air conditioning compressor is not high, while faults in the expansion valve and throttle valve directly lead to poor air conditioning cooling.
8
3
Share

What is the speed for shifting from third gear to fourth gear?

The corresponding speed for shifting from third gear to fourth gear is between 30-60km/h. Below is additional information about gear shifting: 1. RPM: The optimal gear shift timing for most cars is when the engine reaches 2000r/min, preferably not exceeding 2500r/min. For some high-displacement, high-power engines, the maximum efficiency range may be slightly delayed, so shifting around 3000r/min can be considered. 2. Engine: Different vehicles have engines and transmissions that perform differently. Drivers can determine the shift timing by listening to the engine sound. Generally, if the engine sound is dull, it indicates that it's time to upshift.
7
4
Share

Is the Han EV a hybrid?

BYD Han EV offers both hybrid and pure electric versions. Here is an introduction to BYD-related content: 1. Brand History: BYD Company Limited was founded in 1995, starting with a team of just over 20 people. By 2003, it had grown into the world's second-largest rechargeable battery manufacturer and established BYD Auto in the same year. Originating as a battery manufacturer, BYD's venture into automobile production was akin to playing the role of an 'outsider.' However, leveraging its 'independent intellectual property rights' and the acquisition of Qinchuan Auto, BYD gained a first-mover advantage over other newcomers. 2. Brand Introduction: BYD Auto adheres to a development path of independent R&D, production, and branding, committed to creating truly affordable and high-quality vehicles for the public. The product designs not only incorporate advanced international trends but also align with the aesthetic values of Chinese culture.
4
5
Share

Why does the 2010 Yuexiang have high fuel consumption?

The reasons for the high fuel consumption of the 2010 Yuexiang are: 1. Engine issues: Generally, it is necessary to first check the ignition system, such as replacing the spark plugs, and also inspect the fuel supply system, such as cleaning the fuel injectors. 2. Sensor failure: A diagnostic tool is needed to read the data stream and analyze whether there is a sensor malfunction or incorrect signal. 3. Transmission and chassis problems: Issues like transmission slippage or high body resistance can also lead to increased fuel consumption. Below is more information about the Yuexiang: 1. The Changan Yuexiang is a compact car produced by Changan. The differences between the luxury and comfort models lie in the additional features of the luxury version. 2. Main configurations include aluminum alloy wheels, front passenger airbag, rear door child safety locks, 60/40 split-folding rear seats, trunk light, front passenger vanity mirror, electric exterior rearview mirrors (manual folding), chrome steering wheel logo, and sunglasses storage box.
2
5
Share

Should the Haval H2 use 92 or 95 octane gasoline?

According to the official vehicle manual recommendation, the Haval H2 should use 92 octane gasoline. In addition to checking the suitable gasoline grade in the vehicle manual, you can also find it on the fuel tank cap, which will also be marked. Generally, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should choose 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should opt for 95 octane gasoline. If the compression ratio is higher, 98 octane gasoline should be selected. However, with the use of some new technologies nowadays, the gasoline grade cannot be solely determined by the compression ratio. A high compression ratio can also be tuned to use lower octane gasoline because, apart from the compression ratio, other factors such as ignition timing, turbocharging technology, and Atkinson cycle technology also play a role. Generally, the higher the gasoline grade, the higher the octane number and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If the Haval H2 occasionally uses the wrong gasoline grade, simply switch back to the correct grade after using it up. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower octane gasoline, using a higher octane grade will not cause damage, but the increase in octane number will alter the fuel's ignition point, leading to delayed combustion in the engine. This means both the engine's power output and thermal efficiency will decrease, resulting in poorer performance as experienced in practice. For vehicles recommended to use higher octane gasoline, using a lower octane grade can cause engine knocking. Because the octane number is too low, the gasoline's ignition point decreases, causing it to ignite prematurely during the compression stroke. If combustion occurs before the spark plug ignites during the compression stroke, resistance will arise in the upward stroke. This resistance makes the engine run very unstably. If it's mild knocking, it only increases noise without significant damage to the engine. However, if noticeable knocking occurs, it indicates severe engine conditions. The vibrations not only affect driving stability but also cause abnormal wear on the pistons and cylinders, and in severe cases, can lead to cylinder scoring.
1
4
Share

What is the most feared substance entering an engine?

The most feared are granular impurities, as they can render the engine ineffective. Specific details are as follows: 1. Automotive engine: It is the device that provides power for a car, serving as the heart of the vehicle, determining its power, fuel efficiency, stability, and environmental friendliness. Depending on the power source, automotive engines can be classified into diesel engines, gasoline engines, electric vehicle motors, and hybrids, among others. 2. Working principle: A four-stroke gasoline engine mixes air and gasoline in a certain proportion to form a good combustible mixture, which is drawn into the cylinder during the intake stroke. The mixture is compressed, ignited, and burned to generate thermal energy. The high-temperature and high-pressure gas acts on the top of the piston, pushing it to perform reciprocating linear motion, thereby outputting mechanical energy externally through the connecting rod and crankshaft flywheel mechanism. A four-stroke gasoline engine completes one working cycle during the intake stroke, compression stroke, power stroke, and exhaust stroke.
15
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.