Why is water dripping under the front of the car?

1 Answers
DeLane
07/29/25 10:09am
There are two possible reasons for water dripping under the front of the car: air conditioning system drainage and radiator leakage. The details are as follows: Air conditioning system drainage: In summer, the outdoor temperature is high while the temperature inside the car with air conditioning on is low, creating a temperature difference that causes water to drip from the chassis. The low-pressure pipes of the car's air conditioning system are not wrapped with thermal insulation foam, making the pipe surfaces prone to condensing moisture from the air. Water droplets will also condense and gather at the lowest point of the pipes, then drip down. Radiator leakage: The radiator is located next to the car's engine. If the radiator connections become loose, leakage can occur. In this case, the dripping water will be colored, usually red or green.
Was this review help?
18
4
Share
More Forum Discussions

Is It Harmful for Car Tires to Soak in Water?

Short-term soaking of car tires in water is not harmful. However, if car tires are soaked in water for a long time, or if the car is parked in stagnant water where the water level reaches the wheel hub, the impact on the wheel hub and brake components can be significant. Since wheel hubs and brake components are mostly made of metal, soaking in water can cause oxidation reactions, leading to rust on the wheel hub and brake parts, which in turn affects the car's braking performance. Tires are rubber products and are insoluble in water. They are vulcanized, offering high corrosion resistance and heat resistance, so short-term soaking in water is acceptable. However, prolonged soaking in water can still have some effects. Due to friction with the ground, the tire surface develops indentations, allowing some pollutants to enter the tire. When these pollutants come into contact with water, chemical reactions may occur, potentially damaging the tire. Things to note if car parts rust after soaking in water: If rust does occur, it can be resolved by lightly sanding with fine sandpaper. However, if the corrosion is severe, replacement is necessary. Even if the rusted parts are sanded off as much as possible, it can still affect braking performance (e.g., steering wobble during braking, unusual noises, etc.). Moreover, wheel hubs and brake components are different—they are made of metal and can undergo oxidation reactions with standing water. Over time, this can corrode the metal parts (rusting), significantly impacting the car's braking performance. For daily tire maintenance, pay attention to the following: Regularly inspect the tire surface for cracks, deformations, or other defects. Due to driving wear, the tread grooves gradually become shallow. If the tread wears out completely, it loses its water drainage and anti-slip functions, greatly reducing the car's performance. Small cracks can also become hazards for tire blowouts at high speeds. Additionally, promptly remove pebbles stuck in the grooves. Park on flat ground whenever possible. Avoid parking on roads with thick, sharp, or pointed stones. Do not park near or in contact with petroleum products, acids, or other materials that can deteriorate rubber. After parking, avoid turning the steering wheel, as this accelerates tire wear. Do not splash water to cool tires. In hot weather or during high-speed driving, tires can overheat, increasing air pressure. In such cases, park to allow the tires to cool naturally. Avoid releasing air to reduce pressure or splashing water to cool them, as this can cause abnormal aging of the tread rubber. Avoid sudden braking. Try to minimize frequent or hard braking to prevent accelerated tread wear from dragging against the ground.
1
3
Share

Why Does Porsche Brake Squeak?

Porsche brake squeaking can be caused by hard particles entering the brake disc or poor brake disc fixation. Below are detailed explanations and solutions: 1. Hard particles entering the brake disc: Sometimes, hard particles like sand or stones can get into the gap between the brake disc and the brake pad, causing noise. This usually occurs during the initial driving phase and can generally be ignored. Solution: Clean the brake disc. 2. Poor brake disc fixation: Poor fixation of the brake disc can also lead to brake noise and may cause uneven wear. Solution: Replace the brake disc.
7
4
Share

How to Fix Incorrect Ignition Timing Angle?

There are two methods to correct incorrect ignition timing angle: the correction coefficient method and the corrected ignition timing angle method. Below is an expanded introduction: 1. Main correction items: coolant temperature correction, idle stability correction, and air-fuel ratio feedback correction. 2. Introduction to correction values: Since there are many parameters that affect engine operation, some parameters have a greater impact on engine performance, while others have relatively minor effects. However, to ensure that the engine operates with maximum power, minimal fuel consumption, and the lowest emissions of harmful gases under various conditions, it is necessary to monitor these relatively minor parameters and use them as auxiliary adjustment parameters. These parameters are referred to as correction values.
17
1
Share

Why does a BMW shake a few times after ignition and then stall?

The reasons why a BMW shakes a few times after ignition and then stalls include cylinder misfire and severe carbon buildup in the cylinders. Below are detailed explanations of the causes and solutions: 1. Cylinder misfire: This is the most common cause of engine shaking. The issue lies with the engine ignition coil or spark plugs. If the ignition coil malfunctions or the spark plugs fail to fire for some reason, the car will experience shaking. Solution: Replace the engine ignition coil or spark plugs. 2. Severe carbon buildup in the cylinders: If severe carbon buildup in the cylinders causes the engine spark plugs or valves to become clogged, the engine will also shake. Solution: If the car's acceleration performance has deteriorated and the shaking is persistent, consider cleaning the engine cylinders.
10
5
Share

What is the real range of Tesla Model-Y?

The vehicle's low-speed range energy consumption this time was 19.9kWh/100km. Here is the relevant introduction about Tesla Model-Y: 1. Exterior: The actual Tesla Model-Y features a blue body with a very grand and sporty appearance, adopting a simple body style. The front face design is very minimalist and fashionable, with rounded headlights that exude a refined feel. The side profile boasts clean and full body lines, with a roofline design that gives it a coupe-like SUV style, complemented by sporty wheel designs. The rear end presents a bold and simple shape, featuring three-dimensional line designs. 2. Interior: The interior dashboard design is very minimalist, with a center console screen that is both grand and full of technological appeal.
6
4
Share

What is the function of the ES button on a Mercedes-Benz car?

Mercedes-Benz car's ES button is the switch button for the Mercedes-Benz economy mode. The following is detailed information about Mercedes-Benz: 1. Related to models: Mercedes-Benz is the oldest car manufacturer in the world, famous for producing high-quality, high-performance luxury cars. Mercedes-Benz is also one of the top ten car companies in the world, ranking first in Germany by sales revenue and second by sales volume. 2. Function: The ES button can shift gears earlier, which is more fuel-efficient but has weaker acceleration. The ES switch button on an automatic transmission means that it can switch between sport mode and economy mode. The ES switch button can be switched at any time, just press it directly.
14
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.