Why is there no license renewal service on 12123?

1 Answers
LilahRose
07/29/25 9:51pm
12123 does not offer the license renewal service because the renewal period is not within 90 days. Below is relevant information about license renewal: 1. Renewal method: Bring the required documents and medical examination report to the vehicle management office. After filling out the "Motor Vehicle Driver's License Application Form," you can renew your license for free. 2. Handling expired licenses: If the license has been expired for less than a year, it can be renewed normally; if expired for more than one year but less than three years, the license will be canceled, but it can be renewed by passing the subject one test; if expired for more than three years, the license becomes invalid and cannot be renewed; driving with an expired license is treated as driving without a license and may result in a 200 yuan fine.
Was this review help?
16
1
Share
More Forum Discussions

What Happens When the Clutch Switch Fails?

Symptoms of a faulty clutch switch: 1. Transmission slippage during rapid acceleration. This is primarily caused by excessive wear of the clutch disc. If the clutch disc is too thin, it can easily slip and spin against the friction plate, especially noticeable during sudden acceleration. 2. Inability to shift gears when the clutch is depressed. This can occur due to a broken clutch cable or a malfunction in the hydraulic system. The clutch cable is responsible for pulling the clutch pressure plate; if it breaks, the clutch cannot disengage, making gear shifting impossible. 3. Difficulty in shifting gears. A manual transmission can only shift gears when the clutch disc and friction plate are fully separated. If the clutch fails to disengage completely after being depressed by the driver, shifting gears becomes very difficult.
4
1
Share

How to Repair Car Tires?

About the methods of car tire repair are as follows: 1. Traditional plug method. This is a rather primitive method. The principle is to first use a sharp tool like an awl to enlarge the puncture hole, then fill the hole with a rubber strip coated with glue. It's simple to operate, very low cost, takes little time, and doesn't require separating the tire from the rim or performing wheel balancing. The downside is obvious: using an awl to enlarge the hole increases the damaged area, and this repair method is not very durable, often leading to air leaks. 2. Patch repair method. This is the most common method, used by most tire repair shops. First, separate the tire from the rim, then sand the damaged area inside the tire to help the glue adhere better. Clean up the sanding debris, apply some special tire repair glue to the damaged area and its surroundings, stick the repair patch onto the damaged area, press it firmly, and then apply another layer of glue. 3. Mushroom plug repair. The mushroom plug is currently the most advanced tire repair method, belonging to the internal repair category. It requires separating the tire from the rim, and wheel balancing must be performed after the repair is completed. The difference between the mushroom plug and the patch repair method is that the mushroom plug can effectively fill the gaps in the puncture hole, preventing further expansion of the damaged area.
5
0
Share

What does 'check' mean on a car display?

The 'check' light in a car is the engine indicator light, which is used to display the working condition of the engine. This indicator light shows the operational status of the engine. When you turn the ignition key, the light will illuminate during the vehicle's self-check and then turn off automatically. If it remains lit, it indicates that there is a fault with the engine, requiring inspection and repair. Below are descriptions of various lights on the car dashboard: 1. Door status indicator. This light shows whether the doors are fully closed. If a door is open or not properly closed, the corresponding light will illuminate to alert the driver. It turns off once the door is closed. 2. Parking indicator. This light comes on when the parking brake (handbrake) is engaged. It turns off automatically when the handbrake is released. In some models, this light may also indicate low brake fluid. 3. Battery indicator. This light displays the working status of the battery. It lights up when the ignition is turned on and turns off after the engine starts. If it doesn’t light up or stays on continuously, the generator and circuit should be checked immediately. 4. Fuel indicator. This light warns of low fuel. When it illuminates, it means the fuel is nearly depleted. Typically, the vehicle can still travel about 50 kilometers after this light comes on before running out of fuel.
17
3
Share

Why is the Vehicle Stability Control System Light On?

The illumination of the Vehicle Stability Control System light is primarily caused by a malfunction in the vehicle's electronic stability control system. In such cases, it is recommended to visit a 4S dealership to use a professional diagnostic scanner to read the fault codes, followed by repairs based on the identified codes. The Vehicle Stability System, also known as the ESP system, mainly consists of three components: sensors, actuators, and the electronic control unit. Below is an introduction to the related content: 1. The sensors mainly include wheel speed sensors, steering angle sensors, lateral acceleration sensors, yaw rate sensors, and brake master cylinder pressure sensors. The actuators primarily consist of traditional braking systems and hydraulic modulators. The electronic control unit works in conjunction with the engine management system, allowing for intervention and adjustment of the engine's power output. 2. The Vehicle Stability System is an active safety feature in automobiles that significantly enhances vehicle handling and safety. During sharp turns or sudden acceleration, the vehicle's sensors can quickly detect these conditions and take appropriate measures to control the tires accordingly while reducing engine power output to ensure vehicle stability. 3. The Vehicle Stability Control System also includes ABS and ASR. ABS prevents wheel lock-up during braking, and ASR prevents wheel spin during acceleration.
19
1
Share

What to Do When the Steering Wheel Shakes After Changing Tires?

The solution to steering wheel shaking after changing tires: perform dynamic balancing. More information about dynamic balancing is as follows: 1. The most widely used balancing methods are process balancing and on-site machine dynamic balancing. As an important branch of on-site machine dynamic balancing technology, online dynamic balancing technology is also in a period of vigorous development and shows great promise. 2. Dynamic balancing can not only eliminate the dynamic unbalance couple but also the centrifugal force caused by static unbalance. 3. Any method that can only determine the position of the rotor's unbalanced weight and the location and size of the balance weight to be added while the rotor is in motion is called dynamic balancing.
4
3
Share

What Does It Mean When the EPC Warning Light Comes On?

When the EPC warning light illuminates in a vehicle, it indicates the following: 1. A steady EPC light typically signifies a fault in the engine management system or electronic control, often accompanied by symptoms like unstable idle speed or engine shaking during cold starts. For most Chinese car owners, this is usually caused by poor fuel quality or a dirty operating environment. It's recommended to drive to a service station for inspection as soon as possible. In most cases, cleaning the throttle body can resolve the issue. 2. The EPC indicator lights up during the functional check when the ignition is turned on. If this light comes on while driving, it indicates a malfunction in the engine's electronic power control system, requiring immediate engine inspection. Common causes include a dirty throttle valve body, vacuum leaks in the intake system, faulty brake switches, or overdue engine software upgrades. 3. There are two other possible reasons for EPC illumination. One is a dirty throttle body that needs cleaning; the other is non-functioning brake lights, which can be fixed by replacing bulbs or checking the brake switch and wiring.
20
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.