···
Log in / Register

Why is there no air blowing from the front windshield?

3 Answers
CamilaLynn
08/28/25 3:37am
Reasons for no air blowing from the front windshield: blower failure, clogged air filter. Blower failure: The car blower is a crucial component of the car's air conditioning system. If the air conditioning compressor fails during use, the car's air conditioning will definitely not blow air. Overheating damage to the internal coil or capacitor failure of the blower are significant causes of blower malfunction. You can turn the car's air conditioning to the maximum and listen for the sound of the blower. If it is confirmed to be a blower failure, it needs to be addressed at a 4S shop as it is difficult to resolve on your own. Clogged air filter: The air filter is a common and significant reason for the air conditioning not blowing air. During operation, the car's air conditioning system absorbs many impurities from the air, leading to clogging of the air filter. If the air conditioning is not blowing air, you can remove the air filter and check if it is clean. If the air filter is too dirty, it needs to be replaced promptly. You can go to a 4S shop or a repair shop, or you can replace it yourself.
Was this review help?
17
1
Share
McBethany
09/10/25 2:12am
That day on my way home from work, it suddenly started pouring rain, and the windshield fogged up instantly. I pressed the defroster button but got no airflow at all—I was really panicked! Recalling past experience, the first common cause is incorrect AC mode selection: if the knob isn't turned to the windshield defrost position, air will flow through other vents. Quickly check and adjust this. If the issue persists, the fan speed switch might be set too low or turned off; try manually setting it to maximum and listen for any sound. Clogged vents are also very common, especially when parked—dust or small leaves can fall in and block the passage; a simple wipe and clean might help. If all these are fine, the problem could be deeper, like a blown fuse or faulty fan motor. In such cases, don't risk driving—safely pull over and call for roadside assistance or visit a repair shop for diagnosis. Safety first. Regular maintenance with vent cleaning can prevent such troubles.
Was this review help?
14
2
Share
Expand All
LeReed
10/24/25 3:01am
I enjoy tinkering with cars in my spare time, and when I encounter issues like no air coming from the front defroster, I can usually figure out the problem myself. First, check the AC settings: make sure the knob is set to defrost mode, not mistakenly set to foot or face vents. Next, test the fan speed—turn it up and listen for the fan noise; if there's no sound, check the corresponding fuse in the fuse box (usually under a small cover on the driver’s side). If it's blown, just replace it. If the vents are clogged, you can use a vacuum or small tools to clean them out. Last time, my car’s vents were completely blocked by dust buildup, and clearing them fixed the issue. For deeper problems like a stuck air blend door actuator or a faulty fan, you’ll need to carefully disassemble with wrenches. As part of regular maintenance, I use compressed air to periodically clean the vents to prevent dust accumulation.
Was this review help?
11
5
Share
Expand All
More Forum Discussions

What is the operation method of wheel alignment?

The wheel alignment operation process is as follows: 1. Drive the vehicle onto the four-post alignment lift and check the tire pressure and vehicle height. 2. Lift all four wheels off the ground for the next step of inspection. 3. Check the tires for irregular wear, deformation, etc. If the wear reaches the acceptable minimum standard, data can be measured. 4. Inspect the upper and lower suspension, stabilizer bar, subframe, and chassis for any deformation or looseness. 5. Check the rear axle, lateral control rod, and rear tie rod for deformation and whether the rubber bushings are loose. 6. After confirming no abnormalities, lower the vehicle and shake it several times to ensure the suspension system is in normal condition. Then, remove the wheel alignment locking pins. 7. Turn on the computer and prepare for the detection process. Secure the steering wheel, install the wheel alignment sensors, connect the cables, and enter the wheel alignment detection system. Follow the computer's operating sequence to read the data. 8. Based on the deviation of the alignment angle data, determine whether adjustment or replacement of parts is necessary. 9. Adjust the alignment angles starting from the rear wheels to the front wheels. The front wheel toe angle should be adjusted last, as adjustments to other alignment angles can align the thrust angle with the vehicle centerline, which will affect the front wheel toe. 10. Rear wheel camber adjustment: Install the camber adjustment tool on the shock absorber and tighten or loosen it according to the required alignment angle. 11. Adjust the rear wheel toe: The toe can be increased or decreased by adjusting the length of the lateral control rod.
17
0
Share

Why can't I play music when my Lynk & Co is connected to Bluetooth?

If you cannot listen to music after connecting your Lynk & Co 03 to Bluetooth, it may be because the Bluetooth volume on your phone or the car's audio system is not turned on, or the connection between the car's Bluetooth and your phone's Bluetooth is not properly established. Here are other reasons why there might be no music when connected to Bluetooth: Incompatible pairing code: If the sound is turned on but you still can't play music, it might be due to an incompatible pairing code between the music playback program and the car. In this case, you can still answer calls but cannot play music. It is recommended to change the car's Bluetooth playback audio settings; after changing, the music playback function should work normally. Music option not enabled: If you are playing music on your phone but there is no sound in the car, it is likely because the music option on the car's audio system is not turned on. Once enabled, the music should play.
5
4
Share

What type of transmission fluid is used for the Mazda CX-4?

The Mazda CX-4 uses ATF-FZ transmission fluid. Types of transmission fluid: Transmission fluids are generally divided into three types: manual transmission fluid (commonly known as gear oil), automatic transmission fluid (commonly known as ATF), and continuously variable transmission fluid (commonly known as CVTF). Performance and maintenance methods of transmission fluid: Transmission fluid reduces friction and wear, controls clutch friction and synchronizer performance. It also bears loads (low-speed high torque, vibration loads), dissipates heat, reduces vibration and noise, and cleans contaminants from gear meshing (cleaning function). Additionally, it prevents corrosion, pitting, and surface metal tearing, isolates metal surfaces, and prevents direct metal-to-metal contact. When experiencing body shaking, gear-shift hesitation, or a transmission high-temperature warning on the dashboard, the transmission fluid should be replaced promptly.
2
4
Share

What are the reasons for the loud engine noise in the Trumpchi GS4?

The reasons for the loud engine noise in the Trumpchi GS4 are: 1. Insufficient engine oil or cold engine oil not yet warmed up, leading to inadequate oil pressure; 2. Presence of impurities or excessive dirt in the engine oil, preventing effective regulation of oil pressure; 3. Mechanical interference in the engine or blockage in the lubrication circuit. The Trumpchi GS4 is a compact SUV under GAC Motor, equipped with a 1.5T turbocharged engine delivering a maximum horsepower of 169 PS, a maximum power of 124 kW, and a maximum power speed of 5000 rpm. It features a MacPherson independent front suspension and a multi-link independent rear suspension.
1
4
Share

How to Turn on the Heating in BYD S6?

To turn on the heating in a BYD S6, rotate the temperature control knob to the red zone and then turn on the fan speed switch. Taking the 2014 BYD S6 Manual Flagship model as an example, it is a mid-size SUV with body dimensions of 4810mm in length, 1855mm in width, and 1725mm in height, a wheelbase of 2720mm, and a fuel tank capacity of 72 liters. The 2014 BYD S6 Manual Flagship is equipped with a 1.5L turbocharged engine, delivering a maximum power of 113 kW at 5200 rpm, paired with a 6-speed manual transmission.
11
5
Share

Where are the Mazda 6 sunroof drainage outlets located?

The Mazda 6 sunroof has one drainage outlet at each of the four corners of the sunroof. When you open the sunroof, you can easily see four small holes, each connected to a hose that leads to the front and rear of the car. If these drainage holes at the four corners become blocked, water cannot drain properly and may seep into the interior. The hazards of blocked drainage outlets and cleaning methods are as follows: Hazards of blocked drainage outlets: If the drainage holes at the four corners are blocked, water cannot drain properly and may seep into the interior. In severe cases, water may flow along the roof to the sunroof motor inside the car. If the sunroof motor is used while powered on, it may short-circuit and burn out. Cleaning methods: Initially, blockages occur at the entrance of the drainage holes, which can be easily seen and cleaned by opening the sunroof. Over time, debris may enter the drainage hoses and move further inside, making it harder to clear. In such cases, it is best to visit a 4S shop and have a professional technician perform the cleaning.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.