Why is there a small light flashing continuously when the car is locked?

2 Answers
VanJesse
07/28/25 7:30pm
It is normal for a small light to flash after the car is locked. This is the car's anti-theft light, and its flashing indicates that the car has entered the anti-theft state. Here are some explanations about the car's anti-theft light: 1. The car's anti-theft light generally serves as a warning. When the light is on, it reminds the owner that the vehicle has entered the anti-theft state, and the owner does not need to worry. 2. If the car's engine anti-theft light flashes at a frequency of once every 1 to 2 seconds, it is a normal phenomenon, indicating that the car's engine has entered the anti-theft state and the engine anti-theft system is working. If the anti-theft light does not light up, it is usually caused by a malfunction of the vehicle's anti-theft device or the anti-theft light.
Was this review help?
11
2
Share
ErinRose
08/12/25 12:32am
When you lock the car and notice a small light flashing continuously, it reminds me of a similar situation I've encountered. That small light is usually the indicator for the anti-theft system. A regular blinking pattern typically means the system is activated, protecting the vehicle from theft. For example, in my car, a few flashes per second indicates everything is normal, designed to warn potential thieves that the car has security measures in place. However, if the light flashes unusually fast, too brightly, or without interruption, there might be a minor issue—the most common causes being a door not properly closed or the key left inside the car, which the sensors failed to detect. Check if all doors are securely locked and the key is removed; sometimes, a low battery can also cause abnormalities, as the anti-theft system requires stable voltage. I recommend first consulting the manual to confirm the specific function of the light. If that doesn’t help, visit a professional shop to inspect the electrical circuit to rule out any potential security vulnerabilities. Addressing it promptly can prevent misunderstandings or potential risks.
Was this review help?
19
5
Share
Expand All
More Forum Discussions

Can the Fit use 95-octane gasoline?

The Fit can use 95-octane gasoline. This vehicle requires a minimum of 92-octane gasoline. Gasoline is a volatile, flammable hydrocarbon mixture liquid distilled or cracked from petroleum, used as fuel. The Fit is a hatchback launched by GAC Honda, with a body length of 4065mm, width of 1695mm, height of 1525mm, and a wheelbase of 2530mm. The Fit is equipped with a 1.5L direct-injection DOHC i-VTEC engine, delivering a maximum power of 96kW and maximum torque of 155Nm, paired with a CVT transmission. It features direct fuel injection technology and uses an aluminum alloy cylinder head and block.
8
3
Share

How to Check Fuel Level on a Mercedes-Benz Fuel Gauge?

The fuel gauge shows the fuel level in the vehicle's tank. When the needle points to 0, it indicates that the fuel tank is low on fuel. When the needle points to 1, it means the fuel tank is full. If the needle is between 0 and 1, it indicates that the tank is half full. Based on the fuel level, it is recommended to add fuel in a timely manner and not wait until the fuel warning light comes on. Here is some relevant information about the vehicle's fuel tank: 1. Introduction: The automotive fuel tank is the full name of the car's fuel container. Currently, with the development of the automotive industry and the revitalization of the domestic automobile sector, the demand for automotive fuel tanks from major automobile manufacturers has shown a significant upward trend. 2. Design Principle: The design utilizes the heat energy generated by the engine during operation, incorporating a thermal circulation system between the engine, fuel tank, and radiator. The original single fuel tank is redesigned into a combined fuel tank consisting of a main tank and an auxiliary tank.
1
2
Share

Mustang: Should You Use 92 or 95 Octane Fuel?

According to the official vehicle manual recommendation, the Mustang should use 95 octane fuel. In addition to checking the appropriate fuel grade in the vehicle manual, the Mustang owner can also find this information on the fuel tank cap, which is usually labeled. Generally, the fuel grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane fuel, while those with a compression ratio between 10.0-11.5 should use 95 octane fuel. However, with the application of new technologies, the compression ratio alone cannot determine the fuel grade—high compression ratios can still be tuned to use lower octane fuel. This is because other factors, such as ignition timing, turbocharging technology, and Atkinson cycle technology, also play a role. Generally, the higher the fuel octane number, the higher the octane value and the better the anti-knock performance. 92 octane fuel contains 92% isooctane and 8% n-heptane, while 95 octane fuel contains 95% isooctane and 5% n-heptane. If the Mustang occasionally uses the wrong fuel grade, simply switch back to the correct grade after consumption. However, long-term use of the wrong fuel grade can have the following effects: For vehicles recommended for low-octane fuel, using higher octane fuel will not cause damage, but the increased octane value alters the fuel's ignition point, leading to delayed combustion in the engine. This reduces both the engine's power output and thermal efficiency, resulting in poorer performance. For vehicles recommended for high-octane fuel, using lower octane fuel can cause engine knocking. Due to the significantly lower octane value, the fuel ignites prematurely during the compression stroke. If combustion occurs before the spark plug fires, resistance is generated during the upward stroke. This resistance makes the engine run very unevenly. If the knocking is mild, it may only increase noise without obvious engine damage. However, severe knocking indicates critical engine conditions, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, and in extreme cases, cylinder scoring.
3
0
Share

What is the tire model of BYD Han?

BYD Han's tire model is 245/45R19. The first number 245 indicates the tire width is 245MM, 45 means the aspect ratio of the tire section is 45%, that is, the section height is 45% of the width, and 19 represents the rim diameter is 19 inches. The middle letters or symbols have special meanings: "X" denotes high-pressure tires; "R", "Z" indicate radial tires; "-" represents low-pressure tires. BYD Han can accelerate from 0 to 100 km/h in 7.9 seconds. In addition to the model, tires are also marked with the following common data: Tire cord material: Represented by Chinese pinyin, such as M-cotton cord, R-rayon cord, N-nylon cord, G-steel cord, ZG-steel radial cord. Speed rating: Indicates the maximum speed at which the tire can carry a specified load under specified conditions. Letters A to Z represent certified speed ratings from 4.8km/h to 300km/h. Common speed ratings include: Q: 160km/h; H: 210km/h; V: 240km/h; W: 270km/h; Y: 300km/h; Rim specification: Shows the rim size compatible with the tire for practical use, such as "Standard Rim 5.00F".
13
1
Share

How to Replace the Battery in a Kia K5 Key Fob?

Method for replacing the battery in a Kia K5 key fob: 1. Remove the mechanical key, then insert a flat-head screwdriver into the slot marked by the red circle and pry it open with force; 2. Once a gap is created, use both hands to pull the key fob apart; 3. After opening, you will see one half containing the circuit board and the other half with the coin cell battery, where the positive side of the battery faces down; 4. Use the screwdriver to pry out the coin cell battery. When installing the new battery, ensure the side with the text faces downward. After replacing the battery, snap the two halves of the key fob back together. The Kia K5 is a mid-size sedan under Dongfeng Yueda Kia, with body dimensions of 4845mm in length, 1835mm in width, 1455mm in height, and a wheelbase of 2795mm.
13
1
Share

Should You Release the Handbrake or Shift to D Gear First When Starting an Automatic Transmission Car?

When starting an automatic transmission car, first shift to D gear and then release the handbrake. It is essential to keep the brake pedal pressed. The order can be reversed without major issues, but it is crucial not to forget to release the handbrake. Starting with the brake pedal pressed can easily burn out the brake pads. If you're a beginner and not yet accustomed to the process, you can release the handbrake first to avoid forgetting it after starting. Whether it's a manual or automatic transmission car, the most important step when starting is to shift into gear first and then release the handbrake. The handbrake serves as the final safety measure. Only after fully engaging the gear and before moving should you release the handbrake—this practice is very safe. When shifting gears, move quickly from P to D to avoid passing through R, which can cause a backlash and harm the transmission. If you engage the gear but do not release the handbrake, all the power output from the engine will be absorbed by the torque converter, causing its temperature to rise sharply. Prolonged exposure to this condition can burn out the torque converter. For dual-clutch transmissions, after engaging the gear, the clutch friction plates will remain in a semi-engaged state. Prolonged semi-engagement can lead to burning out the friction plates, so it's necessary to start moving as soon as possible. Generally, if you don't press the brake pedal before starting an automatic transmission car, it can negatively impact the vehicle's transmission and gear structure. This effect is even more pronounced when the car is parked on an incline.
6
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.