Why is there a processing fee for Subject 3?

1 Answers
ChaseMarie
07/29/25 12:10pm
Driver's license processing fees are usually only required for license replacement. The Subject 3 exam fee applies when you haven't obtained a driver's license yet - there's no fee for initial license issuance, only for retakes or replacements. The Subject 3 exam fee is typically paid by the driving instructor and included in the tuition. If you fail the test, the student needs to pay the retake fee. Here's an introduction to the Subject 3 exam content: The road driving skills test for Subject 3 generally includes: vehicle preparation, light simulation test, starting, straight-line driving, gear shifting operations, lane changing, pulling over, going straight through intersections, left turns at intersections, right turns at intersections, crossing pedestrian crossings, passing school zones, passing bus stops, meeting vehicles, overtaking, U-turns, and night driving. The safe and civilized driving knowledge test generally includes: requirements for safe and civilized driving operations, safe driving knowledge in adverse weather and complex road conditions, emergency handling methods for situations like tire blowouts, and post-accident handling knowledge.
Was this review help?
7
3
Share
More Forum Discussions

How to Add Freon to a Land Rover Velar?

The methods for adding Freon to a Land Rover Velar are: 1. High-pressure side filling: Suitable for filling after leak detection and vacuuming; 2. Low-pressure side filling: Involves adding gas and is used for replenishing refrigerant. The Land Rover Velar is an SUV under the British brand Land Rover. Taking the 2020 Range Rover Velar P250 as an example, its body dimensions are: length 4811 mm, width 2032 mm, height 1685 mm, with a wheelbase of 2874 mm. The 2020 Range Rover Velar P250 is equipped with a 2.0T 250 horsepower L4 engine, with a maximum power of 184 kW and a maximum torque of 365 Nm.
9
4
Share

Does Using the Heater in Winter Increase Fuel Consumption?

Using the heater in winter does not increase fuel consumption. The warm air comes from the heat generated by the engine during operation. After the engine's cooling system dissipates heat from the engine, a fan directs this heat into the car's interior. The steps to turn on the heater are: 1. Press the recirculation button; 2. Adjust the temperature to the heating mode; 3. Set the airflow direction to blow forward and toward the feet. The functions of the car's air conditioning system are: 1. To regulate and control the temperature, humidity, air cleanliness, and airflow inside the car to optimal conditions; 2. To provide a comfortable environment for passengers, reducing travel fatigue.
18
3
Share

What are the effects of a car wading through water?

The effects of a car wading through water are: 1. Residual water can prevent the brake discs and brake pads from fully engaging, causing the car to lose braking power; 2. Rainwater on the road is dirty and contains various debris. When a vehicle wades through water, these debris can easily adhere to the gaps in the chassis, leading to rust over time; 3. When a vehicle wades through water, water can enter the headlights, forming mist inside them, which affects the light transmission and directly impacts driving safety; 4. There are many wiring harnesses and circuits in the engine compartment. When a vehicle wades through water, the interfaces of the wiring harnesses can get wet, causing short circuits; 5. Water entering the cabin floor or exhaust pipe can cause engine damage.
15
3
Share

How to Remove the Wiper Blades on the New Excelle?

The steps to remove the wiper blades on the New Excelle are: 1. Lift and remove the wiper arm; 2. Stand the wiper upright, adjust the blade angle to form a 90-degree angle with the wiper arm; 3. Lift the wiper blade to expose the locking hook, then detach the entire blade. Taking the 2021 Excelle as an example, it is a compact car under SAIC-GM Buick with body dimensions of 4609mm in length, 1798mm in width, 1464mm in height, and a wheelbase of 2640mm. It features front-wheel drive, with a front MacPherson strut suspension and a rear multi-link independent suspension.
3
4
Share

How to Deal with Fog Inside the Car?

Solutions for fog inside the car include: 1. Keep a damp towel in the car and wipe away the fog when it appears; 2. If fog is caused by a significant temperature difference between the inside and outside of the car, open the windows to equalize the temperatures; 3. When the windshield fogs up, switch the air circulation system to external circulation; 4. Turn on the automatic climate control; 5. Spray an anti-fog agent on the windshield to form a protective film; 6. Turn on the air conditioner's cold air. Reasons for fog inside the car are: 1. Under certain humidity conditions, when the window temperature is below the dew point, condensation forms on the window surface; 2. A temperature difference on either side of the window causes the saturated vapor pressure on the cooler side to be lower than the surrounding environment's vapor pressure; 3. Moisture gathers on the glass surface, forming tiny water droplets that create fog.
7
1
Share

What Causes Engine Piston Slap Noise?

The reasons for engine piston slap noise are: 1. Excessive clearance between piston and cylinder; 2. Incorrect piston installation direction or piston deformation; 3. Bent or twisted connecting rod; 4. Excessive carbon deposits in combustion chamber increasing diesel engine compression ratio; 5. Clogged lubricating oil passages; 6. Overly rapid combustion of air-fuel mixture. The solutions for engine piston slap noise are: 1. When engine temperature is normal but knocking sound exists, avoid high-speed operation and perform disassembly and repair as soon as possible; 2. Check whether the cylinder is severely out-of-round or scratched, and whether the piston-to-cylinder clearance is too large - replace cylinder liner, piston, and piston rings promptly if needed.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.