Why is the right side always too narrow or out of line when reversing into the right parking space?

1 Answers
GenesisLee
07/29/25 5:28pm
The reasons and solutions for the right side always being too narrow or out of line when reversing into the right parking space are as follows: Turning the steering wheel too early: After starting to reverse into the parking space, turning the steering wheel for the first time too early will result in the left side being too wide and the right side too narrow; next time when practicing reversing into the parking space, turn the steering wheel a bit later at the original point. Solutions: Control the driving speed by using first gear or reverse gear idle speed throughout the process, maintaining the same speed as when starting. Control the timing of steering by observing carefully during the reversing process, mastering the key points of steering and turning at the right time. Control the driving route during the test, as the car's route mainly depends on the speed of turning the steering wheel and the driving speed. When reversing, aim accurately at the side lines and correct the direction in time to keep the car straight when entering the parking space.
Was this review help?
7
0
Share
More Forum Discussions

How to Remove and Install the Door Panel of an Audi Q5?

The steps to remove and install the door panel of an Audi Q5 are: 1. Pry out the trim panel on the inner handle row; 2. Remove the screws under the inner armrest and the screws under the door trim panel, then lift upwards to remove the panel; 3. Install by following the reverse order of the removal steps. The body dimensions of the Audi Q5 are: length 4753mm, width 1893mm, height 1659mm, wheelbase 2908mm, and fuel tank capacity 73 liters. The Audi Q5 is equipped with a 2.0-liter turbocharged engine with a maximum power of 169 kW. Its drive system is front-engine four-wheel drive, with a five-link independent suspension at the front and a trapezoidal link independent suspension at the rear.
20
0
Share

How to Replace the Battery in a Besturn B70 Key?

Besturn B70 key battery replacement method is: 1. Press the white button at the top to eject the mechanical metal key; 2. Locate the hidden section and pry open the key along the seam; 3. Remove the old battery and insert a new one. Taking the 2021 Besturn B70 as an example, its body dimensions are: length 4810mm, width 1840mm, height 1455mm, with a wheelbase of 2800mm and a fuel tank capacity of 50l. The 2021 Besturn B70 is equipped with a 1.5T turbocharged engine, delivering a maximum power of 124kW and a maximum torque of 258Nm, paired with a 6-speed manual transmission.
5
4
Share

Where is the car air conditioning installed?

The car air conditioning is installed in the following locations: 1. The compressor is mounted on the engine and driven by the engine crankshaft belt; 2. The condenser is installed behind the front grille of the car for heat dissipation; 3. The expansion valve and evaporator are installed under the car dashboard. The components of the car air conditioning system include: compressor, condenser, expansion valve, and evaporator. The functions of the car air conditioning are: 1. To adjust and control the temperature, humidity, air cleanliness, and airflow inside the cabin to an optimal state; 2. To provide a comfortable environment for passengers, reducing travel fatigue; 3. To create good working conditions for the driver, ensuring driving safety.
4
3
Share

What Causes the Abnormal Noise at Idle That Disappears When Depressing the Clutch?

Abnormal noise at idle that disappears when depressing the clutch is caused by: 1. Loose release bearing on the clutch producing the noise; 2. Loose transmission input shaft bearing, transmission gear failure, or transmission fork malfunction. Idle refers to an operating condition of a vehicle where the engine runs in neutral gear, and the engine speed during idle is called idle speed. The clutch is a component that ensures smooth vehicle starting and seamless gear shifting. Its working principle is: 1. When starting the vehicle, depressing the clutch separates the pressure plate from the friction disc, at which point the pressure plate and flywheel are completely disengaged; 2. During normal driving, the pressure plate is tightly pressed against the flywheel's friction disc, creating significant friction between them, maintaining relative static friction between the input and output shafts, which then rotate at the same speed.
17
0
Share

How to Turn Off the Headlights of a Mercedes-Benz?

To turn off the headlights of a Mercedes-Benz, follow these steps: 1. Start the vehicle; 2. Locate the vehicle light adjustment button on the lower left side of the steering wheel; 3. Turn the light button to 'auto' to turn off the headlights. Taking the Mercedes-Benz C260 as an example, its body dimensions are: length 4704mm, width 1810mm, height 1454mm, wheelbase 2840mm, and fuel tank capacity 66L. The Mercedes-Benz C260 is equipped with a 1.5T turbocharged engine, with a maximum power of 135kW and a maximum torque of 280Nm, paired with a 9-speed automatic transmission. It adopts a multi-link independent suspension system for both front and rear suspension.
8
5
Share

Does the Lavida have an engine guard?

Lavida does not have an engine guard, only an anti-rust treatment for the chassis when leaving the factory. Lavida is a model under the Volkswagen brand, with body dimensions of: length 4670mm, width 1806mm, height 1474mm, wheelbase 2688mm, fuel tank capacity 51l, and body structure as a 4-door 5-seater sedan. The Lavida is equipped with a 1.4T turbocharged engine, with a maximum power of 110kW and a maximum torque of 250Nm, paired with a 7-speed dual-clutch transmission. The front suspension type is MacPherson independent suspension, and the rear suspension type is torsion beam non-independent suspension.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.