Why is the Hyundai Verna consuming high fuel?

1 Answers
VanAlina
07/28/25 4:12pm
There are several reasons why the Hyundai Verna may have high fuel consumption: 1. Check if the spark plug gap is too large. If there is an issue with the spark plugs, the ignition circuit will not function properly, leading to higher fuel consumption. Consider replacing the spark plugs. 2. Clogged fuel lines or excessive carbon buildup. Carbon deposits can block the fuel lines, resulting in higher fuel consumption. Use a fuel system cleaner to clean the fuel injectors and throttle body. 3. Inspect the tire wear. Excessive tire wear can also increase fuel consumption. It is advisable to replace the tires. 4. Check for fuel injector leaks. Leaking fuel injectors can cause high fuel consumption. Consider replacing the fuel injectors. 5. Excessive carbon buildup on the valves. Too much carbon on the valves can lead to higher fuel consumption. It is recommended to clean the throttle body and perform an engine carbon cleaning.
Was this review help?
7
5
Share
More Forum Discussions

What does roz/ron90-98 mean?

roz/ron90-98 represents the gasoline octane rating, indicating that this type of gasoline can be used within the octane value range of 90 to 98. Gasoline is a volatile and flammable hydrocarbon mixture liquid derived from the distillation and cracking of petroleum. Relevant information about gasoline additives is as follows: 1. Introduction: A gasoline additive is a liquid that enables complete combustion of automotive gasoline, typically added directly to the fuel tank along with gasoline. 2. Function: Using gasoline additives to clean the fuel system and regularly employing them to control carbon deposit formation can consistently maintain the engine in optimal condition.
6
0
Share

Where is the tire pressure display located on the 2021 Classic Sylphy?

The tire pressure of the 2021 Classic Sylphy is displayed on the vehicle's dashboard. The Classic Sylphy model uses an alarm system for tire pressure and does not display specific numerical values. When the tire pressure is insufficient, a warning light will appear on the dashboard to alert the driver. Functions of the Sylphy's tire pressure monitoring system: 1. Prevent accidents. The tire pressure monitoring system is a type of active safety device that can alert the driver in time when there are signs of danger in the tires, prompting the driver to take appropriate measures, thereby avoiding serious accidents. 2. Extend tire lifespan. With the tire pressure monitoring system, we can ensure that the tires always operate within the specified pressure and temperature range, reducing tire damage and extending their lifespan. Data shows that driving with insufficient tire pressure reduces tire lifespan by 15% when the pressure is 10% below the normal value. 3. Improve fuel efficiency. When the tire pressure is too low, the contact area between the tire and the ground increases, leading to higher friction resistance. When the tire pressure is 30% below the standard value, fuel consumption increases by 10%. 4. Reduce wear on the suspension system. Overinflated tires reduce the tire's own shock absorption effect, increasing the burden on the vehicle's suspension system. Long-term use can cause significant damage to the engine chassis and suspension system. Uneven tire pressure can also lead to braking deviation, increasing wear on the suspension system.
13
5
Share

How to switch between D gear and S gear in a car?

To switch between D gear and S gear in a car, simply push the gear lever directly. Below are some related introductions about D gear and S gear: 1. The automatic D gear refers to the manual mode of a manual-automatic transmission, which allows manual control of gear shifting (both upshifting and downshifting). When using D gear, there is no need to press the brake or release the accelerator. 2. S gear is the sports mode of a car. The transmission can shift freely, but the shifting timing is delayed, keeping the engine at high RPM for a longer time. This allows the car to run at low gear and high RPM for an extended period, resulting in greater torque output and acceleration.
10
0
Share

How long does it take to fully charge a car battery after jump-starting the vehicle?

After a car battery runs out of power, the vehicle's engine needs to maintain a speed of over 2000 RPM, and the car must be driven for at least 4 hours to fully recharge the battery. If the engine speed cannot reach 2000 RPM, the charging time will be even longer. The alternator in the car requires a speed of over 2000 RPM to operate at full capacity, at which point its power generation reaches the nominal value specified on the nameplate. Here are some car battery maintenance tips: 1. Avoid using in-car electrical devices for extended periods while the engine is off. 2. Avoid continuous attempts to start the vehicle. 3. Always turn off the lights after parking. 4. Do not leave the car unused for long periods without starting it.
19
5
Share

Which gear should an automatic transmission car be in when parked with the air conditioning on?

When parking an automatic transmission car with the air conditioning on, it is best to shift to neutral. Here are the relevant details: 1. Precautions: If you want to use the air conditioning after the car has stopped, you must start the car engine to avoid draining the battery, which could make it difficult to start the car later. 2. P gear: The P gear is the most common gear in automatic transmission cars, usually located at the front of the gearshift console, before the R gear, and is designed to lock the axle when the car is stationary on a slope. The car must be started in neutral (N) gear, and the air conditioning should be turned on only after the engine has stabilized at idle speed.
19
0
Share

How to Adjust the Rearview Mirrors on a Lavida Car?

Lavida car rearview mirror adjustment method is as follows: The Volkswagen Lavida rearview mirror adjustment switch is located on the driver's side door. For the left side exterior rearview mirror, adjust by turning the knob at the L position up, down, right, or left; for the right side exterior rearview mirror, adjust by turning the knob at the R position up, down, right, or left. Extension: The left side rearview mirror of the car has better visibility with a smaller blind spot, allowing for a larger adjustable observation range. Position the horizon in the middle of the rearview mirror. It's best to have a view that covers the rear of the car, making driving and reversing more convenient. Key points for adjusting the left rearview mirror: Place the horizon at the midline position of the rearview mirror, then adjust the edge of the car body to occupy 1/4 of the mirror's image.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.