Why is the Haval network not working?

1 Answers
DelZoey
07/29/25 11:35pm
Here are the reasons and solutions for the Haval network not working: 1. Poor network coverage around the vehicle: Driving into an underground garage or traveling in remote areas with weak signal coverage can cause the vehicle to lose network connection or have a weak signal. The network connection will automatically restore once the vehicle moves out of the area with insufficient coverage, requiring no special handling. 2. Signal interference: Driving near military management zones or similar areas can cause interference with the vehicle's network signal, leading to unstable or interrupted connections. The network signal will return to normal once the vehicle leaves the restricted area, requiring no special handling. 3. The infotainment system needs an upgrade: If the vehicle has not been on the market for long, the infotainment system might not be fully optimized, leading to unstable program operations. When the system is handling multiple tasks, it may experience lag or errors, causing abnormal network functionality, intermittent connections, or complete disconnections. In such cases, the owner can consider upgrading the infotainment system to improve its performance. Start the infotainment system and check for any new software version updates when the network connection is stable. If an update is available, proceed with the upgrade. This can be done via OTA (Over-The-Air) updates by the owner at no cost. 4. Data traffic is turned off: If the data traffic is disabled, the infotainment system will not have network access. The owner can check whether the data traffic switch is turned off and manually reactivate it through the infotainment system without any additional cost.
Was this review help?
20
5
Share
More Forum Discussions

Should You Use Internal or External Air Circulation When Sleeping in the Car?

When sleeping in the car, you should use external air circulation to ensure proper air flow inside the vehicle. If the surrounding environment has poor air circulation and the car is left idling while you sleep, carbon monoxide produced during idling can accumulate and fail to dissipate, potentially leading to carbon monoxide poisoning inside the car, which can have severe consequences. External circulation mode uses a fan to draw outside air into the car, meaning the air passages between the outside and inside of the car are open. The air blown by the fan comes from outside, and even if the fan is not turned on, air will still be drawn into the car while driving, replenishing the fresh air inside. Sometimes, you may feel airflow even when the fan is off, which is because the external circulation mode is set.
9
4
Share

What causes the ticking sound after the engine shuts off?

The reason for the ticking sound after the engine shuts off is that the engine cooling system is still working, which is the sound of the electric fan operating. Precautions for using car engines are as follows: Avoid driving in neutral: The engine itself has a fuel cut-off function during deceleration, and driving in neutral is not conducive to fuel economy. Pay attention to observation when using the vehicle: If oil is found on the ground, determine whether there is an engine oil leak and communicate with the car 4S store in time to eliminate potential safety hazards. Do not turn off the engine immediately: For cars equipped with turbochargers, do not turn off the engine immediately after high-speed driving or climbing a slope. Let the engine idle for 10 minutes before shutting it off. Cars with turbochargers accumulate carbon deposits several times faster than naturally aspirated cars.
9
0
Share

What Causes the Rear Door to Not Lock?

The rear door not locking is likely due to damage. Below is relevant information about vehicle emission standard inquiries: Methods to check vehicle emission standards: The vehicle's model number will be indicated on the nameplate. Visit the Motor Vehicle Environmental Protection website, enter the fuzzy condition (vehicle model number) in the input box, input the correct verification code, and click 'Query' to retrieve the vehicle's information, including the emission standard. How to locate the vehicle nameplate: There is usually a nameplate under the front passenger door. Other possible locations include the lower left corner of the windshield, the driver's door pillar, the left side of the dashboard, the engine compartment, adhesive labels on the side doors, the base of the door frame, or inside the glove box, where you may find relevant labels displaying the vehicle model number.
17
3
Share

How often should the timing belt of the new Focus be replaced?

Mocha hybrid fuel consumption: It is generally recommended to replace the timing belt at around 120,000 to 130,000 kilometers. Common issues that may arise: Abnormal noise, insufficient tension, which can easily cause the belt to skip teeth. Installation method of the timing belt for the new Focus car engine: Turn the intake and exhaust camshafts of the car to the horizontal position, fix the crankshaft pulley to the front cover, and the timing belt installation is complete. The Focus car uses a timing belt system, so it performs better in terms of noise and engine transmission compared to the timing chain system. Components such as the timing belt tensioner, tensioner, and water pump will experience varying degrees of wear and aging, so regular maintenance of the timing belt is necessary.
8
0
Share

Does the Audi A6 have auxiliary braking when the start-stop is activated?

Audi A6 still has auxiliary braking when the start-stop is activated. Conditions for the automatic start-stop system to work: The driver's door must be closed, the driver must fasten the seat belt, the engine hood must be closed, and during use, the vehicle must be braked to a standstill and the brake must be pressed. Automatic start-stop troubleshooting: When the vehicle is temporarily parked or stops before a traffic light, the engine shuts off by itself for a short time. When resuming driving, there is no need to operate the ignition key, and the engine will start again. While driving, when the vehicle encounters congestion or a red light, the driver presses the brake until the vehicle stops and keeps the brake pressed without releasing it. At this point, the engine automatically shuts off and then restarts.
20
5
Share

Does Changing Brake Pads on a Mercedes Require Decoding?

Mercedes does not require decoding when changing brake pads. Method for replacing rear brake pads on a Mercedes: First, open the engine compartment cover of the brake fluid reservoir and observe the brake fluid level. Prepare the new brake pads for replacement, then remove the old brake pads and check for excessive wear or cracks. During the removal process, be careful to avoid scratching the rims. Procedure for replacing rear brake pads on a Mercedes: Use the X-431PADIII device, select the special function and click to enter. After connecting, choose the Mercedes model, select automatic scanning, turn on the ignition switch as prompted, and then click OK to proceed.
17
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.