···
Log in / Register

Why is the fuel consumption of Refine so high?

5 Answers
MacJackson
07/24/25 4:03am

There are many factors that can lead to excessive fuel consumption, such as driving habits (sudden acceleration, sudden braking, coasting in neutral, speed and gear mismatch), low tire pressure, use of low-quality fuel, ignition system failure, and electronic control system failure. These issues will all increase the vehicle's fuel consumption. The specific reasons for high fuel consumption are as follows: 1. Idling: When the car is idling, fuel continues to be consumed while the mileage does not increase, inevitably leading to higher fuel consumption. 2. Warm-up time: The fuel injection volume is very large during idle warm-up. Prolonged warm-up before driving in winter will cause an increase in fuel consumption. 3. Driving conditions: Frequent starts and stops in traffic jams will inevitably lead to wasted fuel. Choosing a good driving route is an effective way to reduce fuel consumption. 4. Driving habits: Poor driving habits have a significant impact on fuel consumption. Sudden acceleration and braking waste a lot of fuel and increase the wear on brake pads and discs.

Was this review help?
5
4
Share
PrestonFitz
08/10/25 10:12pm

As a veteran driver who has been driving the Refine for many years, I can relate to the frustration of high fuel consumption. The main issue lies in the somewhat outdated engine design, especially in older models where the powertrain isn't very efficient, leading to noticeably higher fuel usage during acceleration. Additionally, the vehicle's weight is significantly heavier than typical sedans. When fully loaded with passengers or cargo, the engine has to work much harder, causing fuel consumption to spike. From my daily driving experience, regular maintenance is crucial—things like a dirty air filter or underinflated tires can increase fuel consumption by over 10%. On highways, the high wind resistance also drives up fuel usage. Overall, using better engine oil or maintaining speeds between 60-80 km/h can help somewhat, but it still consumes more fuel compared to newer models.

Was this review help?
7
3
Share
Expand All
NorahLynn
09/24/25 5:01am

I just bought a used Refine not long ago, and the high fuel consumption really surprised me. I mainly drive in the city, often braking and accelerating sharply, and the dashboard frequently shows the fuel consumption exceeding the standard. Plus, I use the air conditioning frequently, which makes it even more fuel-hungry in summer. I feel that maintenance needs attention—checking if the tire pressure is too low, whether the engine oil has been changed, as these directly affect fuel efficiency. Additionally, the car often carries the whole family or loads; the Refine is inherently an MPV with a heavy design, slow to start and with high wind resistance. I suggest keeping a record of the mileage per tank of gas and driving more smoothly to save a lot of money. Using the cruise control system more often during highway driving can also help.

Was this review help?
20
0
Share
Expand All
LaOlivia
11/07/25 7:13am

The high fuel consumption of the Ruifeng is mainly related to its model. I noticed this when using the vehicle for cargo transport. The heavy body, weak power, and sluggish acceleration lead to increased fuel consumption, especially noticeable in stop-and-go city traffic. Poor aerodynamics and high wind resistance require more fuel to maintain speed. Additionally, as the vehicle ages, component efficiency declines—for example, a faulty oxygen sensor can cause incomplete combustion. On long trips, I use maps to choose flatter routes and avoid uphill sections, which helps slightly, but overall, as a multi-purpose vehicle, its fuel consumption is inherently high.

Was this review help?
14
0
Share
Expand All
FranciscoLee
12/29/25 2:10am

Having driven for many years, I pay close attention to fuel consumption issues. The high fuel consumption of the Refine may stem from multiple detailed factors. Poor engine maintenance, clogged air filters leading to excessive fuel injection, and aging circuits causing incomplete combustion are among the reasons. Heavy vehicle load and additional power consumption from the air conditioning system can also increase fuel consumption. In daily driving, I make sure to avoid frequent starts and high-speed emergency braking, opting instead for eco-mode. Additionally, checking tire wear and maintaining correct tire pressure can significantly reduce fuel consumption. Overall, it's a high-fuel-consumption model, so one should be mentally prepared when choosing it.

Was this review help?
9
2
Share
Expand All
More Forum Discussions

What are the effects of water in gasoline on the engine?

If there is water in the gasoline, it will affect the normal combustion of the gasoline in the cylinder, leading to symptoms such as abnormal engine shaking, poor acceleration, and difficulty starting. Below is some relevant information about automotive gasoline: 1. Overview: Automotive gasoline is a liquid fuel refined from petroleum, mainly used for cars and motorcycles. 2. Classification: In China, automotive gasoline is divided into unleaded and leaded types. The unleaded types have octane ratings of 90, 93, and 95 RON (Research Octane Number). The leaded types have octane ratings of 90, 93, and 97 RON. Among them, the lead content in 90 RON does not exceed 0.35g/L, while the lead content in 93 and 97 RON does not exceed 0.45g/L.
11
4
Share

What are the impacts of transferring a driver's license registration location?

Transferring a driver's license registration location has no impact on the individual. Below are the relevant details regarding changes to driver's license information: 1. Explanation: Within the jurisdiction of the vehicle management office, if the information of the motor vehicle driver recorded on the driver's license changes, the driver must apply for a replacement license at the vehicle management office that issued the original license within 30 days. When applying, the driver must fill out an application form and submit their identity proof and the original driver's license. 2. Notes: If the driver's household registration is moved out of the original vehicle management office's jurisdiction, they must apply for a replacement license at the new jurisdiction's vehicle management office. When applying, the driver must fill out an application form and submit the following documents: the driver's identity proof and the original driver's license.
20
1
Share

Is it necessary to opt for FSD when buying a Tesla Model 3?

It is not necessary to opt for FSD when buying a Tesla Model 3, as FSD cannot be legally used on Chinese roads. Here are the specific details about the Tesla Model 3: 1. Vehicle Positioning: The Model 3 is a mid-sized electric vehicle with a wheelbase of 2875 mm, and dimensions of 4694 mm in length, 1850 mm in width, and 1443 mm in height. 2. Powertrain: The Model 3 is available in both rear-wheel drive and all-wheel drive versions. The all-wheel drive version is a dual-motor model, while the rear-wheel drive version is a single-motor model. The total power output of the all-wheel drive version is 340 kW, with a total torque of 639 Nm. The rear-wheel drive version has a maximum power output of 202 kW and a maximum torque of 404 Nm. 3. Battery: The Model 3 is equipped with ternary lithium batteries across all variants, which offer higher energy density and are lighter in weight.
17
4
Share

What to Do When Car Window Fails to Roll Up or Down?

Window one-touch up/down malfunction can be restored by pulling up or pressing the corresponding window switch and holding it, raising the window glass to the top, then releasing the window switch and pulling up or pressing it again. Relevant details are as follows: 1. One-touch window refers to a system where the car window glass can be controlled to move up or down to position with one press. Cars equipped with one-touch windows have a two-stage window control switch. The first stage works like a regular power window. The second stage allows the window to fully open or close automatically with a single press and release. In contrast, regular power windows require holding the switch until the window reaches the desired position, then releasing to stop the movement. 2. Nowadays, most mid-to-high-end models are equipped with one-touch window functions, mainly for the convenience of drivers and passengers, avoiding distraction from operating windows and improving safety. One-touch windows generally feature an "anti-pinch" function to prevent the risk of pinching fingers.
4
3
Share

How to Turn on the High Beam in Lavida?

Lavida's high beam control switch is located on the combination light lever on the left side of the steering wheel. To turn on the high beam, first activate the low beam by rotating the light knob, then press the combination light lever downward to engage the high beam. The high beam indicator on the dashboard will illuminate simultaneously. Below are related instructions for Lavida's high beam: The procedure for replacing the high beam bulb in the Volkswagen Lavida is as follows: 1. After turning off the vehicle, wait for the engine to cool down completely before opening the engine hood to avoid burns from high engine temperatures. 2. After opening the hood, locate the dust cover of the headlight assembly, which is typically made of rubber. Remove the high beam dust cover to access the bulb base inside the headlight assembly, then disconnect the wiring harness connector. 3. Pinch the wire clip next to the base, and once the clip loosens, the bulb can be removed directly. 4. Install the new bulb, and please observe electrical safety precautions when handling electrical components.
6
3
Share

What are the effects if the heating wire breaks during film application?

Impurities left on the air conditioning filter can mold and breed bacteria, which may harm the health of drivers and passengers, and even induce respiratory diseases. The following is relevant information about electric heating films: 1. Introduction: Low-temperature electric heating film is a semi-transparent polyester film that generates heat when electrified. It is made by processing and hot-pressing conductive special ink and metal current-carrying strips between insulating polyester films. During operation, the electric heating film serves as the heating element, radiating heat into the space, warming the human body and objects first. Its overall effect is superior to traditional convection heating methods. 2. Heating Principle: The heating principle of electric heating films involves the carbon molecular clusters in the heating element producing "Brownian motion" under the action of an electric field. Intense friction and collisions occur between carbon molecules, generating thermal energy that is transmitted externally in the form of far-infrared radiation and convection, with an electricity-to-heat conversion rate of over 98%. The action of carbon molecules causes the system's surface to heat up rapidly. When the electric heating film heating system is installed on walls (or floors), thermal energy is continuously and evenly transmitted to every corner of the room.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.