Why is the dash cam not recording?

Will highways only accept ETC in the future?

Highways do not exclusively use ETC. Vehicles without ETC can still access highways. According to regulations by the State Council, vehicles without ETC will not enjoy toll discounts and must pay fees through manual lanes. Additionally, newly installed ETC devices cannot be used immediately—they must be activated before functioning normally. During free holiday periods, vehicles can still use highways. For users with activated ETC, passing through ETC lanes will not incur charges. ETC Deduction Principles: Highways feature one or more ETC lanes. The system relies on dedicated short-range microwave communication between the vehicle's on-board electronic tag (installed on the windshield) and the microwave antenna in the ETC lane. This connects to bank backend settlement via computer networking, enabling vehicles to pay tolls without stopping at toll stations—all based on a "pass first, deduct later" principle. Benefits of Installing ETC: Time-saving: Eliminates waiting in queues. Green & eco-friendly: Reduces noise and exhaust emissions by avoiding idling at toll booths. Cost-efficient: Lowers vehicle wear and fuel consumption by minimizing frequent stops and starts. Enhanced efficiency: ETC lanes theoretically process vehicles 2-3 times faster, making traditional ETC more advanced, faster, and high-tech. Compared to license plate payment, ETC technology is more mature and advantageous. Policy Support: The State Council's "13th Five-Year Plan for Modern Integrated Transportation System Development" explicitly aims to "achieve interoperability of transport cards in major city clusters and significantly increase ETC adoption by 2020," with a target of "50% ETC usage rate for road passenger vehicles by 2020" under key transport development indicators. Future Possibilities: Beyond improving ETC convenience and passenger vehicle adoption, future plans include promoting ETC for trucks and integrating ETC systems with vehicle-to-vehicle communication, vehicle-road coordination, and smart transportation initiatives. This will provide comprehensive travel services, expanding ETC application scenarios.

15

5

Share

What are the differences between the GL8 and GL8 ES?

The differences between the GL8 and GL8 ES are: 1. Different powertrains: The GL8 offers a choice between a 2.5L and a 2.0T engine, while the GL8 ES only has a 2.0T engine. 2. Different trunk volumes: The GL8 has a trunk volume of 475 to 1605L, whereas the GL8 ES has a trunk volume of 521 to 1650L. 3. Different suspensions: The standard GL8 uses a torsion beam non-independent suspension (solid axle), while the GL8 ES uses a multi-link independent suspension. Taking the 2021 GL8 as an example, its body dimensions are 5238mm in length, 1878mm in width, and 1776mm in height, with a wheelbase of 3088mm. This model is equipped with a 2.0T turbocharged engine, with a maximum torque of 350Nm and a maximum power of 174kW, paired with a 9-speed automatic transmission.

6

5

Share

Starting and Shutting Down Steps for the 2019 Sagitar

19 Sagitar starting and shutdown steps are as follows: 1. To start, press the brake pedal and push the start button to ignite the engine. 2. For parking and shutdown, first press the brake to bring the vehicle to a complete stop, then shift into P gear, and finally engage the handbrake. Below is relevant information about the Sagitar: The Sagitar is a compact sedan under the Volkswagen brand, equipped with two turbocharged engines across its lineup - a 1.2L turbocharged engine and a 1.4L turbocharged engine. The 1.2L turbocharged engine delivers a maximum horsepower of 116 HP and peak torque of 175 N·m, with maximum power output achieved at 5000-6000 rpm and maximum torque available between 1500-4500 rpm. The 1.4L turbocharged engine produces 150 HP maximum horsepower and 250 N·m peak torque, reaching maximum power at 5000-6000 rpm and maximum torque within 1750-3000 rpm.

1

3

Share

How to Replace Coolant More Thoroughly?

Here is the method for replacing car coolant: 1. Unscrew the radiator cap, open the radiator drain valve located at the bottom of the car, and drain out the coolant. 2. Clean the cooling system by continuously pouring clean water into the engine cooling system. During the flushing process, keep the engine idling to maintain the flow of clean water inside until clear water comes out from the radiator. 3. Stop adding water, wait for the water to drain completely, and then close the drain valve. 4. Fill with new coolant until the liquid level is between the max and min marks. 5. Close the cap, start the car, and let the engine idle for two to three minutes. The cooling system will expel internal air, causing the coolant level to drop slightly. Top up the coolant again if necessary.

14

4

Share

How to Obtain the Annual Inspection Sticker?

Below is a detailed introduction to applying for the annual inspection sticker: 1. Check for any traffic violation records. If there are any, they must be handled at the traffic police station. 2. Prepare the "Compulsory Traffic Accident Liability Insurance Policy," vehicle license, and ID card. 3. Staff will require vehicle photos and inspections. After passing, pay the relevant fees to receive the inspection sticker. 4. Apply online via the 12123 app by uploading photos of the insurance policy and vehicle tax certificate. Below are the precautions: 1. Vehicles exempt from inspection can obtain the sticker if they are non-commercial cars (including large cars) and other small or mini passenger vehicles registered within 6 years. 2. Excludes minivans, 7-seater, and vehicles with more than 7 seats. 3. Excludes vehicles that have not been registered for over 4 years since the manufacturing date. 4. The vehicle must not have been involved in any injury-causing traffic accidents.

3

4

Share

Where is the engine of the Besturn B70 produced?

The production location of the Besturn B70 engine is in Changchun, Jilin, China, and it is also manufactured by FAW Corporation. According to the official introduction of FAW Besturn, the Besturn B70 offers two engine options: a 2.0-liter naturally aspirated engine and a 1.8-liter turbocharged engine, both of which are independently developed by FAW Besturn. Below is some information about the Besturn B70: (1) The Besturn B70 is equipped with Mazda MZR series all-aluminum engines, including the 2.0-liter LF type and the 2.3-liter L3 type. (2) The MZR series engines feature technologies such as S-VT variable valve timing control system, VIS variable intake manifold system, TSCV variable swirl control system, and electronically controlled throttle. (3) The Besturn B70 has a relatively high ownership rate, but its discounts are similar to those of Japanese cars, with significant discounts, resulting in a lower retention rate.

18

3

Share

Why is the dash cam not recording?

Will highways only accept ETC in the future?

What are the differences between the GL8 and GL8 ES?

Starting and Shutting Down Steps for the 2019 Sagitar

How to Replace Coolant More Thoroughly?

How to Obtain the Annual Inspection Sticker?

Where is the engine of the Besturn B70 produced?

How to Handle Scrapping an Old Car?

How to Replace the Battery in a Volkswagen Lavida Car Key?

What brand are the original tires of the Buick Excelle?

What brand is GOFORM tires?