Why is the car key light flashing on the Mazda dashboard?

What is the fuel tank capacity of the GLE?

The fuel tank capacity of the Mercedes-Benz GLE is 85 liters, as officially announced. Owners who have purchased the Mercedes-Benz GLE can also check this information on the vehicle's configuration sheet. The Mercedes-Benz GLE requires 95-octane fuel, with a fuel consumption of 8.9L per 100 kilometers. A full tank can cover a distance of approximately 955km. During daily driving, it is important to always monitor the remaining fuel level. This is typically done by observing the fuel gauge inside the vehicle. If there are no other issues, the fuel level will be accurately reflected on the gauge. The fuel gauge usually has 5 to 6 segments, and it is advisable to refuel when only 2 segments remain to avoid running out of fuel midway. During actual refueling, the amount of fuel added may exceed the marked capacity. This is because the manufacturer's specified fuel tank capacity is measured from the bottom of the tank to the safe fill limit. There is additional space from the safe fill limit to the tank opening, designed to allow for fuel expansion due to temperature increases without causing overflow. If fuel is filled up to the tank opening during refueling, the actual amount of fuel added may exceed the marked capacity.

10

4

Share

What does 'Yield right to left, left to straight, turn to straight' mean?

Left turn yields to straight: In the process of road driving, vehicles turning left should, in principle, give way to vehicles going straight. Right turn yields to left turn: In the process of road driving, vehicles turning right should, in principle, give way to vehicles turning left. Below is the relevant content introduction: Relevant regulations: 'Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China' stipulate that when motor vehicles pass through intersections without traffic signal control or traffic police command, in addition to complying with the provisions of Article 51, paragraphs 2 and 3, it is clearly specified that when motor vehicles pass through intersections without traffic signal control or traffic police command, when traveling in opposite directions, right-turning motor vehicles must yield to left-turning vehicles first; when both are going straight, adhere to the principle of yielding to the right; turning vehicles must yield to straight-going vehicles first.

20

3

Share

How to Solve the Problem of Frequent Stalling During Hill Start in Subject 2?

The solution to frequent stalling during hill start in Subject 2 is to master brake-assisted starting and precise clutch control. Each stall deducts 10 points, and some candidates fail because they don't brake in time, causing the car to roll back more than 30cm. If the car stalls during the test, don't panic—it only deducts 10 points and doesn't result in immediate failure, leaving room for recovery. Below are some key points to note for the Subject 2 test: 1. Adjust the seat properly: Before starting, adjust the seat and fasten the seatbelt before fingerprint verification. 2. Follow test rules: Each test section is monitored by GPS, and the control line (yellow dotted line) marks the test area. Once the front of the car crosses the control line, the test begins, and the rules must be followed strictly. 3. Correct mistakes promptly: If an error occurs, correct it immediately to ensure accuracy and minimize point deductions.

14

1

Share

Where is the car accelerator located?

The car accelerator is installed beneath the throttle pedal. Here are some details about the accelerator: 1. Amplifying throttle signal to enhance static response: The so-called 'acceleration' of an electronic throttle accelerator is primarily achieved by increasing throttle response sensitivity, amplifying the input throttle signal by 50%. 2. Amplifying throttle signal rate to improve dynamic response: When the throttle pedal is pressed, the accelerator calculates the rate of change in the throttle signal based on the degree and duration of the press. The faster the change, the stronger the acceleration demand. The throttle accelerator will then amplify this rate of change, ultimately resulting in better dynamic response during acceleration.

12

1

Share

What does the 6x4 drive configuration mean?

Drive configuration 6x4 indicates that the vehicle has six wheels, with four of them being drive wheels. The drive configuration of trucks is typically represented by the total number of wheels multiplied by the number of drive wheels. The number before 'x' represents the number of tire (groups), and the number after 'x' represents the number of drive wheel (groups). Below is a related introduction: Introduction to the 6x4 drive configuration: 6x4: A common arrangement for many heavy-duty trucks. One front axle is a steering support axle, and two rear axles are drive axles. An axle, also known as a shaft, is connected to the frame or load-bearing body via suspension, with wheels installed at both ends. Its function is to transmit forces and moments between the frame or load-bearing body and the wheels in all directions. The control device of the traction control system is a computer that monitors the speed of all four wheels and the steering angle of the steering wheel. When the vehicle accelerates, if the computer detects a significant speed difference between the drive wheels and non-drive wheels, it immediately determines excessive driving force and sends a signal to reduce the engine's fuel supply, thereby lowering the driving force and reducing the slip rate of the drive wheels. Advantages of the 6x4 drive configuration: The advantage of the 6x4 drive configuration is having four drive wheels, which provides stronger driving force and better road adaptability, especially on slippery surfaces like winter snow and rain, enhancing vehicle stability and reducing the risk of skidding or loss of control. The downside is that on roads with good conditions, tire wear and fuel consumption are relatively higher. The drive axles are also heavier and more complex in structure compared to load-bearing axles, resulting in a higher vehicle weight and purchase cost.

19

5

Share

What are the differences between escape1 and escape2?

1. Transmission components: Escape2 uses an 8-speed M310 groupset with an aftermarket chainring. Escape1 uses a complete Shimano groupset with M370 front derailleur, M430 rear derailleur, M391 chainring, and M355 hydraulic disc brakes, which is one level higher than Escape2's configuration. 2. Cost-performance ratio: Escape2 offers better value for money. For beginners, Escape2 is recommended. During continuous riding and learning, you can upgrade the bike according to your actual needs.

15

2

Share

Why is the car key light flashing on the Mazda dashboard?

What is the fuel tank capacity of the GLE?

What does 'Yield right to left, left to straight, turn to straight' mean?

How to Solve the Problem of Frequent Stalling During Hill Start in Subject 2?

Where is the car accelerator located?

What does the 6x4 drive configuration mean?

What are the differences between escape1 and escape2?

What is the Refund Policy for 5 Days of Subject 2 Training?

How Many Kilometers Can You Drive with 2 Small Fuel Bars?

What is the detailed explanation of the tenth-generation Civic dashboard?

Why does the Camry's AUTO headlight turn on during the day?