Why is the Buick's power generation higher than 15V?

1 Answers
StAnna
07/30/25 9:21am
The reason why the Buick's power generation is higher than 15V is generally due to a problem with the regulator, such as a loose connection in the magnetic field wire or a loose terminal on the generator. The fault may result in damage to the voltage regulator, rendering the car unable to drive. The generator is typically composed of components such as the stator, rotor, end cover, and bearings. The stator of the generator: It consists of the stator core, winding coils, frame, and other structural parts that fix these components. The function of the stator is to generate alternating current. The rotor of the generator: It consists of components such as the rotor core (or magnetic pole, yoke) winding, retaining ring, center ring, slip ring, fan, and shaft. The function of the rotor is to generate a magnetic field. It is installed inside the stator.
Was this review help?
1
2
Share
More Forum Discussions

Where is the Buick Regal water temperature gauge sensor located?

The water temperature gauge sensor of the Regal is located directly above the junction of the engine and transmission, on the side of the cylinder head. Damage to the water temperature gauge sensor can cause the gauge to remain at the same level, leading to incorrect judgments by the driver. A faulty water temperature sensor should be replaced promptly, as it can affect driving safety. Solutions for excessively high water temperature are as follows: 1. Insufficient coolant in the cooling system causing engine overheating: Park the car and add coolant after the engine cools down; 2. Loose or broken water pump or fan belt causing engine overheating: Visit a repair shop to replace the relevant parts; 3. Radiator guard mesh or radiator core ventilation duct blocked by debris: Resulting in poor heat dissipation and engine overheating. Replace the radiator guard or clean the debris; 4. Insufficient engine oil or substandard oil quality: Causing engine overheating. Simply replace with high-quality oil.
12
0
Share

How long does it take for a tire to bulge after rubbing against a curb?

Generally, bulging occurs when driving quickly over uneven road surfaces, and rubbing against a curb usually does not cause bulging. The following are the types of tire bulging: 1. Crown separation: The "crown" mainly manifests as delamination at the top of the tread surface (referred to as the crown). 2. Bead separation: Mainly occurs in radial truck tires. It primarily shows as separation around the rim. Issues during the bead wire closing process can cause the wire ring to crack and delaminate. The rubber around the bead wire ring may age and delaminate due to high temperatures or problems with the rubber compound itself. 3. Sidewall bulging: Mainly occurs in radial passenger car tires when driving too fast over potholes, curbs, or road debris, causing the rim and road surface to squeeze the tire sidewall, leading to broken sidewall cords and localized bulging.
18
2
Share

What is the reason why the rear light of Corolla is always on and cannot be turned off?

First, check whether the switch has been triggered, and then consider the issue of the car light circuit failure. Here is some additional information: 1. Three modes of car lights: ON is the always-on mode. When this switch is turned on, the ceiling light will stay on and will not turn off even after the car is locked. DOOR mode means the light will only turn on when the door is opened. OFF is the off mode. Selecting this mode will keep the ceiling light off and it will not light up. 2. Other reasons: If the always-on mode is accidentally activated, the rear seat light will stay on after the vehicle is turned off. If the rear seat light remains on even after the switch is turned off, it could also be due to the vehicle door not being closed properly when getting out of the car, which can cause the interior light to stay on.
17
2
Share

Should I Replace One or Both Front License Plates If One Is Lost?

If the front license plate is lost, you should replace both. Below are the functions of license plates: 1. Identifying the vehicle's region: The primary function is to determine the vehicle's region of registration. 2. Facilitating inquiries: The license plate can also be used to look up the vehicle's owner and registration details. In most countries, any vehicle driven on public roads must display license plates, with strict regulations on size, font, and color. Additionally, in some countries, motorcycles and exempted vehicles may only need to display one license plate.
12
5
Share

Will a novice be penalized for stalling at a traffic light and not moving?

Failure to proceed when the light turns green will result in penalties and fines. According to regulations: a red light indicates prohibition of passage, a green light indicates permission to proceed, and a yellow light serves as a warning. Driving against traffic signal instructions will incur a fine and a deduction of 3 points. When encountering traffic congestion at an intersection ahead, motor vehicles must wait in line outside the intersection and must not enter it. Below are common traffic violations: 1. Running a red light: This is the most common violation. Since the new traffic regulations were implemented, running a red light results in an immediate deduction of 6 points. 2. Driving without a license: If a driver continues to drive while their license is suspended, they will face a fine and 15 days of detention. Driving without a license or with a revoked license will result in 15 days of detention and a fine. 3. Overloading or overcrowding: For passenger vehicles exceeding the rated capacity by less than 20% or freight vehicles exceeding the rated load by less than 30%, a fine will be imposed. Exceeding these thresholds will result in higher fines. 4. Drunk driving: Driving under the influence of alcohol will result in a 3-month suspension of the driver's license and a fine. Driving a commercial vehicle under the influence will also result in a 3-month suspension and a fine. 5. Speeding: Exceeding the speed limit by more than 50% will result in a fine and revocation of the driver's license.
3
4
Share

Must the driver's license photo have a white background?

The background color of the driver's license photo should be white. Specific requirements: the background color must be white, no red clothing (affects stamping), women should not wear earrings, no photos with draped hair during shooting, men's hair should not be too long, the headshot must be clear with a natural expression. The photo size should be 32mm×22mm, with a head width of 14mm-16mm and a head length of 19mm-22mm. Documents required for applying for a driver's license: 1. The "Motor Vehicle Driver's License Application Form" filled out as per regulations; 2. Medical institutions at or above the county level designated by the provincial health bureau or military; 3. Original and photocopy of the applicant's identity proof; 4. Original and photocopy of the applicant's foreign driver's license (if applicable); 5. Six photos of the driver.
9
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.