Why is the brake light of Dongfeng Fengguang 580 always on?

1 Answers
DiJosephine
07/30/25 12:08am
If the brake light of Dongfeng Fengguang 580 remains constantly illuminated, it indicates a potential system malfunction. It is recommended to use an automotive diagnostic scanner at a repair shop, where technicians will perform corresponding repairs based on the fault codes. Below are relevant details: 1. Possible causes: During driving, the force applied to the brake pedal is transmitted through the master cylinder piston, which sends brake fluid to each wheel's brake cylinder. This action causes the brake pads to contact the wheels, thereby achieving braking. Insufficient brake fluid is often accompanied by noticeably reduced braking power, and in severe cases, complete loss of braking force may occur. Low brake fluid levels can cause the brake pedal to sink, keeping the brake switch continuously energized and resulting in constant illumination of the brake light. 2. Powertrain: The Fengguang 580 is equipped with two engine options: a 1.8L naturally aspirated engine and a 1.5L turbocharged engine. The 1.8L naturally aspirated engine delivers 139 horsepower with a maximum torque of 187 N·m, featuring multi-point fuel injection technology, and utilizes an aluminum cylinder head with cast iron cylinder block.
Was this review help?
11
0
Share
More Forum Discussions

Why is the engine warning light constantly on in the new Regal?

The engine warning light may illuminate due to the following 7 main reasons: Sensor malfunction: This includes sensors such as coolant temperature, crankshaft position, air flow, intake air temperature, and oxygen sensors. When these sensors are damaged, have poor contact, or experience signal interruption, the vehicle's ECU cannot accurately obtain engine data, triggering the warning light. Fuel/oil quality issues: Failure to use fuel and engine oil as specified by the manufacturer may cause engine wear, leading to warning light activation. Poor fuel mixture combustion: This can cause engine carbon buildup or knocking. When detected by oxygen sensors and reported to the ECU, the warning light activates. Causes include spark plug failure, ignition coil issues, fuel pump malfunction, or fuel line blockage. Turbocharging problems: Issues with intake boost pipes or turbochargers (most commonly turbocharger damage) can trigger the light. Symptoms may include oil leaks, excessive oil consumption, power loss, metallic noises, or blue/black exhaust smoke. Intake system issues: Air intake problems may lead to engine pipe blockage, potentially causing the warning light. Dirty air filters or lack of regular cleaning can cause intake issues. Exhaust system problems: Exhaust faults (often involving the rear oxygen sensor, catalytic converter, or exhaust camshaft bearings) may activate the warning light. Common causes include using leaded gasoline, improper lubricant additives, physical damage to the catalytic converter, or fuel system malfunctions. Anti-theft system failure: Malfunctions in the electronic anti-theft system or mismatches between the anti-theft controller and engine ECU can prevent normal engine operation and trigger the warning light. When the engine warning light illuminates, follow these steps: 1. First check if the engine operates normally. If there's shaking, smoke, etc., avoid restarting - especially if the red warning light is on. 2. If the engine starts, turn it off for 5-10 minutes. Then without pressing the brake, press the start button or turn the key halfway to ON position (without depressing clutch). After 5-10 seconds of self-check, observe if the warning light turns off. 3. If the light remains on, visit a service center promptly. Technicians can use diagnostic tools to read trouble codes and perform targeted repairs.
9
3
Share

BYD Song: Should I Use 92 or 95 Octane Gasoline?

According to the official vehicle manual recommendation, the BYD Song should use 92 octane gasoline. In addition to checking the appropriate gasoline grade in the vehicle manual, you can also find this information on the fuel tank cap, which is usually labeled. Typically, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with a compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. However, with the application of new technologies, the compression ratio alone cannot determine the gasoline grade, as high-compression engines can also be tuned to use lower-octane gasoline. This is because, besides the compression ratio, other factors such as ignition timing, turbocharging technology, and Atkinson cycle technology also play a role. Generally, the higher the gasoline grade, the higher the octane number and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If you occasionally use the wrong gasoline grade in your BYD Song, simply switch back to the correct grade after the current tank is used up. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower-octane gasoline, using higher-octane gasoline will not cause damage, but the increased octane number can alter the fuel's ignition point, leading to delayed combustion in the engine. This reduces the engine's power output and thermal efficiency, resulting in poorer performance. For vehicles recommended to use higher-octane gasoline, using lower-octane gasoline can cause engine knocking. Due to the significantly lower octane number, the gasoline's ignition point decreases, causing premature ignition during the compression stroke. If combustion occurs before the spark plug fires during the compression stroke, resistance will arise during the upward stroke. This resistance makes the engine run very unstably. If the knocking is mild, it may only increase noise without obvious engine damage. However, noticeable knocking indicates severe engine conditions, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, and in severe cases, cylinder scoring.
13
5
Share

How to resolve the engine warning light issue in Mercedes-Benz C260?

If the engine warning light is on in your Mercedes-Benz C260, you can follow these steps to address the issue: First, check if the engine is running normally and whether there are issues such as shaking or emitting black smoke. If these symptoms are present, avoid restarting the engine. Particularly, if the red light is on, do not attempt to start the engine under any circumstances. If the engine can be started, turn it off and wait for 5-10 minutes. Without pressing the brake pedal, simply press the start button once, or turn the car key halfway to the 'on' position without depressing the clutch. The car will perform a self-diagnosis upon powering up. Wait for 5-10 seconds and observe whether the warning light on the dashboard turns off. If the warning light remains on, visit a service center as soon as possible to identify the cause. The service center can use a portable diagnostic tool to read the fault codes, obtain fault information, and perform targeted repairs. The engine warning light is shaped like a water drop icon and comes in two colors: yellow and red. A yellow light indicates a warning, while a red light signifies a prohibition. When the yellow warning light is on, it means certain system parameters may have exceeded the set range, but the car can still be driven, albeit with some functions limited. When the red warning light is on, the car must be stopped immediately, the engine turned off, and further driving prohibited until the fault is checked. Common causes for the engine warning light to illuminate include: sensor failure, oil quality issues, poor combustion of the air-fuel mixture, turbocharging problems, intake issues, exhaust problems, and anti-theft system malfunctions.
10
2
Share

How to Fix Honda ABS Solenoid Valve Failure?

Open the brake fluid reservoir cap, then use a fluid extractor tool to clean the brake fluid. When preparing to use tool No.11 and tool No.14 to disconnect the hydraulic lines. Use tool No.11 to remove the four hydraulic lines on the ABS pump. After removing the screws from the bracket, create space, and finally pull out the two lines. After removing the entire ABS pump, take off the ABS pump mounting bracket.
18
2
Share

How to adjust the time on Peugeot 3008?

Press the MENU button on the display above the center console. Navigate to DISPLAY-ADJUST and press OK to enter. Use the MENU button to switch between year, month, day, hour, minute, 12-hour or 24-hour format. Press OK to enter and modify each setting. After repeatedly pressing the OK button to adjust the values, wait 10 seconds for the changes to take effect. Alternatively, press ESC to cancel and return.
5
4
Share

How to Defog a Mercedes-Benz on Rainy Days?

In fact, the air conditioning system not only provides cooling but also dehumidification, achieving the fastest defogging effect. For rainy days with lower temperatures, you can switch the air conditioning to heating mode. Let the warm air dry out the moisture inside the vehicle. The most effective method to prevent fogging is to use a professional anti-fog spray, applying it evenly on the cleaned glass surface.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.