Why is the ABS light on in the Tiggo 3?
3 Answers
When the ABS light is displayed on the car, it means there is a fault in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, making it difficult for the driver to slow down or adjust the vehicle's trajectory, posing significant safety risks. There are several states in which the ABS light may illuminate, each with different causes and solutions, as detailed below: State 1: ABS warning light stays on constantly (most common). Cause 1: The ABS speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle's speed or the wheel's slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the dirt from the speed sensor and adjust the gap between the speed sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections in the system wiring or poor contact in the ABS relay, leading to system failure. Solution: Check the wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases, the voltage rises, and the ABS light turns off. This may also occur if the ABS system's power supply voltage is too low, such as due to poor contact in the wiring or grounding. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wiring connector; ABS computer failure. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light illuminates during high-speed driving. Cause: At high speeds, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal, push the brake switch linkage down fully with your finger, then release the brake pedal to complete the self-setting position; replace the brake light switch if necessary.
Bro, if the ABS light on your Tiggo 3 dashboard comes on, I've encountered this a few times. It's usually not a big deal, but you should address it promptly. The most common cause is dirt or damage to the speed sensor near the tires—road debris can block the sensor, causing the system to falsely report a fault. It could also be a minor issue with the module, like moisture in the control unit or aging, loose wiring. If the light stays on and you notice abnormal braking, like wheels skidding during hard stops, this is a safety concern—don't delay. Try disconnecting and reconnecting the battery terminals to see if the light goes off. If that doesn't work, take it to a proper shop to check the fuses and sensors. It won't take much time but is the safer option.
When the ABS light comes on, don't rush to drive fast! This system controls the anti-lock braking function. If the light is on, it means the system isn't fully operational, making it easier to lose control in emergencies. With years of driving experience, I know common triggers: false sensor readings, blown fuses, or wiring issues; occasionally, it could be a module failure. Safety first is my advice: when the light comes on, slow down and pull over. If the brakes still work, drive slowly to get it checked. During inspection, a professional technician can use a diagnostic tool to pinpoint which wheel sensor is faulty—replacing or cleaning it usually solves the problem. Don't skip regular maintenance, especially after driving through muddy areas, as sensors tend to get dirty.
