Why is it difficult to start the car in hot weather?

1 Answers
DeKing
07/29/25 12:09pm
Hot weather makes it difficult to start the car mainly because the engine's air-fuel mixture is not properly matched, resulting in a mixture that is either too rich or too lean. Common causes include the following situations: 1. The fuel evaporation system is used to collect fuel vapor from the fuel tank. The fuel vapor is then introduced into the cylinder at the appropriate time to participate in combustion, thereby preventing the fuel vapor from being directly discharged into the atmosphere and causing pollution. Common issues are caused by the fuel evaporation solenoid valve or activated charcoal canister; 2. Failure of the fuel supply system. For example, poor performance of the fuel pump, clogged filter, or dirty fuel injectors; 3. Failure of the ignition system. For example, poor ignition performance of spark plugs or damaged ignition coils; 4. Sensor problems. For example, issues with the water temperature sensor, camshaft position sensor, oxygen sensor, etc.
Was this review help?
18
2
Share
More Forum Discussions

How to Charge a Tesla?

Tesla charging methods: You can charge through a home charging station or Tesla Supercharger. Superchargers are typically built along major highways, allowing you to take a short break and quickly replenish your battery before continuing your journey. Every Tesla model comes with a home charging station, which can be installed for home charging, providing up to approximately 80 kilometers of range per hour of charging. A full charge consumes only about 68 to 80 kWh of electricity. Tesla is an American electric vehicle and energy company, primarily manufacturing and selling electric vehicles, solar panels, and energy storage equipment. The fastest Tesla model, the P100D, can accelerate from 0 to 100 km/h in just 2.7 seconds and has a maximum range of 570 kilometers. All new Tesla models come equipped with driver-assistance features and full self-driving hardware, allowing for wireless updates via the internet.
10
5
Share

How does the car air conditioner cool?

The main methods for car air conditioning cooling are: 1. Insert the key into the ignition slot and turn it to start the vehicle. 2. Turn on the car air conditioning knob, which can be adjusted to four levels: 1, 2, 3, and 4. The higher the level, the greater the airflow. 3. Adjust the air conditioning to the cooling setting, which is the blue area shown in the figure below. The lower the setting, the stronger the cooling effect. 4. Press the A/C button and adjust the air conditioning to the cooling setting. The car air conditioner will blow cold air. Additional information: 1. The car air conditioning system is a device that cools, heats, ventilates, and purifies the air inside the vehicle cabin. 2. It provides a comfortable environment for passengers, reduces driver fatigue, and improves driving safety. The air conditioning system has become one of the indicators for measuring whether a car is fully equipped.
4
0
Share

How to eliminate the ABS light?

The method to eliminate the ABS light is: go to a professional institution or 4S shop to read the fault code, and then carry out targeted repair. ABS is the anti-lock braking system, whose function is to automatically control the size of the braking force of the brake during car braking, so that the wheels are not locked and are in a state of rolling and sliding, to ensure that the adhesion between the wheels and the ground is at the maximum. During braking, ABS can quickly determine the locking state of the wheels based on the speed signals transmitted by the speed sensor of each wheel, close the normally open input solenoid valve on the wheel that is starting to lock, and keep the braking force unchanged. If the wheel continues to lock, the normally closed output solenoid valve is opened, and the braking pressure on this wheel rapidly decreases due to the pipeline that directly connects to the brake fluid storage tank, preventing the wheel from being completely locked due to excessive braking force.
11
2
Share

What is the correct method for waxing a car?

The correct method for waxing a car is: 1. Rinse the car thoroughly, preferably using a dedicated car wash solution for a complete clean; 2. After rinsing, use a clean cloth to dry the car completely, as water on the paint surface makes waxing difficult. Then, move the car to a shaded area to prepare for waxing; 3. Use a round sponge specifically designed for solid car wax to apply the wax evenly on the paint surface. Do not apply too thick—a thin layer is sufficient. During application, use the sponge to draw circles uniformly on the car body, creating a fish-scale effect with the wax on the paint; 4. After application, wait 5 to 10 minutes to allow the wax to dry completely. Seal the remaining wax for future use; 5. Use a microfiber towel to polish the paint surface, similar to shining shoes, removing excess wax until the car shines like new. This concludes the entire waxing process.
18
1
Share

What are the differences between the Swift and the Swift Sport?

The difference between the Swift and the Swift Sport is that the Swift Sport is fully imported from Japan, while the Swift is domestically produced. The Swift Sport has more power than the Swift. The new Swift Sport has a larger body size, being 60mm longer than the Swift model currently sold in China. Here are more details about the Swift and the Swift Sport: Different transmission configurations: The Swift is equipped with a 5-speed manual transmission, while the Swift Sport has a 6-speed manual transmission. Different body dimensions: The Swift measures 3765mm in length, 1690mm in width, and 1510mm in height, with a wheelbase of 2390mm. The Swift Sport measures 3890mm in length, 1695mm in width, and 1510mm in height, with a wheelbase of 2430mm. Different powertrains: The Swift is equipped with a 1.5L naturally aspirated engine, while the Swift Sport has a 1.6L naturally aspirated engine. Different origins: The Swift is domestically produced, while the Swift Sport is fully imported. The M15A engine in the Swift features a 16-valve DOHC design with WVT continuous variable valve timing technology, delivering a maximum power of 76 kW and a maximum torque of 138 Nm at 4000 rpm. The base model of the Swift Sport is equipped with a K12C 1.2L naturally aspirated engine, producing a maximum output of 67 kW (91 PS) and a peak torque of 118 Nm, paired with a 5MT/CVT transmission. The 1.0T model features a 1.0L turbocharged engine with an output of 75 kW (102 PS) and a peak torque of 150 Nm, matched with a 6-speed automatic transmission. The hybrid version comes with a 1.2L engine + electric motor hybrid system, paired with a CVT transmission, achieving a fuel consumption of 3.64L/100km. In terms of exterior design, the Swift Sport comes with a full sports kit, including a honeycomb front grille that runs from top to bottom. Compared to the Swift, the Swift Sport has a slightly lower body height, more angular front bumper, and horizontal triple fog light accents. The interior differences between the Swift Sport and the Swift are minimal.
9
4
Share

Why is there no sound after successful Bluetooth pairing in the car?

The reasons why there is no sound after successful Bluetooth pairing in the car are: 1. The volume on the phone or the car navigation system is not turned on; 2. The car system is not on the Bluetooth media audio playback interface and is still playing the last media audio source, resulting in no sound when playing music; 3. The Bluetooth driver on the computer is not properly installed. The solution is: Go to the Bluetooth settings interface on the phone, where there are two options: phone audio and media audio. After connecting to the car Bluetooth, both options are turned on by default. You need to turn off the media audio and keep the phone audio, so as to ensure that the three functions of Bluetooth calls, car music playback (or radio), and phone navigation voice announcements do not interfere with each other.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.