Why haven't I received my driver's license after passing Subject 4?

1 Answers
StLola
07/29/25 11:38pm
It may be due to low efficiency at the local DMV. The time to receive the license after passing Subject 4 varies: in some areas, you can get it immediately after passing the exam; in others, it may take about a week; in less efficient areas, it might take up to 15 days. On-the-spot issuance: This is a common method of receiving the driver's license. After passing Subject 4, you wait in a designated lounge, and the licenses are issued collectively. Mailing to the individual: If the DMV is far away and inconvenient to reach, the license may be mailed to you. This is especially convenient for students who take driving lessons during holidays and may need the license when school starts. Pickup at the driving school: In some areas, the licenses are handed over to the driving schools, which then distribute them to students. This is convenient for students who live closer to the driving school than the DMV. Self-pickup at the DMV: In some regions, the licenses are issued a certain period after passing Subject 4, and students need to pick them up at the DMV themselves.
Was this review help?
16
5
Share
More Forum Discussions

Which One is the Accelerator and Brake in a Car?

In cars, the accelerator and brake pedals are arranged differently depending on the vehicle type: 1. Manual transmission: The accelerator and brake are located below the driver's compartment, arranged from left to right as clutch, brake, and accelerator; 2. Automatic transmission: The accelerator and brake are located below the driver's compartment, arranged from left to right as brake and accelerator. The braking system consists of a vacuum booster pump, master brake cylinder, brake caliper, brake pads, and brake discs. The accelerator pedal does not directly control fuel injection. When the accelerator pedal is pressed, it directly controls the throttle valve, increasing its opening to allow more air into the engine. At this point, the ECU commands the fuel injection system to inject more fuel, thereby increasing the engine's RPM and accelerating the vehicle.
12
4
Share

How Often Should You Drive a Car to Avoid Battery Drain?

It is recommended to start the vehicle once a week and drive it every two weeks, covering a distance of three to five kilometers each time. When storing a car for an extended period, pay attention to the following: 1. Pre-storage preparation: Clean the exterior and interior of the car thoroughly before parking it. Applying wax or a protective coating can help prevent corrosion of the paint. If possible, store the car in a garage. If parking outdoors, at least cover the car with a car cover to protect it from sun, rain, and damage from falling leaves and other debris. 2. Brake discs: For vehicles parked for a long time, avoid engaging the handbrake tightly. The brake system, when left unused for extended periods, can react with moisture and oxygen in the air, leading to rust on the brake discs and pads. This can cause them to stick together, affecting braking performance. Upon restarting, this may result in wheel lock-up. 3. Tires: To prevent tire deformation, inflate them to a higher pressure than usual, around 2.8 bar, which is a common practice at 4S shops. Additionally, choose a flat surface for parking to minimize tire damage. Parking on uneven surfaces for long periods can cause tire deformation. 4. Battery: Even when not in use, a car battery discharges internally. A good-quality battery may deplete in about three months, while lower-quality ones may discharge even faster. Therefore, start the engine every one to two weeks to prevent the battery from draining completely and to avoid rust inside the engine. If managing the battery is not feasible, consider disconnecting it or removing the battery cables to slow down the discharge rate.
14
4
Share

Where to Buy Motorcycle Sports Cars?

Motorcycle sports cars can be purchased at motorcycle flagship stores in various cities. Sports motorcycles, also known as sports cars, are designed primarily for leisure and vacation use. They serve as an entertaining means of transportation and a recreational tool to experience the joys of life. The following are the main criteria for identifying a sports motorcycle: 1. High-performance engine, tuned for high-rev power output. 2. Lightweight frame with a focus on sports performance. 3. Fully enclosed fairing (streamlining cover). 4. Low and forward-positioned split handlebars. 5. A horizontally forward-leaning riding posture, which can cause fatigue during long rides.
9
3
Share

Does the Dashboard Need a Protective Film?

Applying a protective film to the dashboard is recommended, as it helps prevent scratches and aging. The specific steps for applying a dashboard film are as follows: 1. Wipe the dashboard with an alcohol pad. 2. Use a dry cloth to wipe the dashboard again. 3. Clean the dashboard with a dust-absorbing sheet. 4. Spray a layer of water onto the dashboard. 5. Peel off the protective film. 6. Spray a layer of water onto the film. 7. Finally, apply the film onto the dashboard. Here are some advantages of dashboard films: 1. You won't have to worry about scratching the dashboard during car washes, maintaining its aesthetic appeal. 2. When the film becomes severely worn after prolonged use, simply replace it with a new one.
7
0
Share

Where is the fuel tank switch located on the Buick Excelle?

The fuel tank switch on the Buick Excelle varies depending on the model: 1. For older models, the fuel cap switch is located between the A and B pillars in the driver's compartment, near the pedals. Press the fuel cap switch to open it. 2. For newer models, simply press lightly around the fuel cap to open it. The Buick Excelle is equipped with: a 1.5L naturally aspirated engine (multi-point fuel injection) paired with an automatic transmission; a 7.0-inch central control screen supporting CarPlay and CarLife; six airbags, tire pressure monitoring, ESP system, and a rearview camera. Dimensions: length 4609mm, width 1798mm, height 1486mm, wheelbase 2640mm.
18
2
Share

How to adjust the valves of a 465 engine?

465 engine valve adjustment method: 1. Align the crankshaft to the top dead center of the first cylinder piston stroke, then adjust the first and second valves on the opposite side of the intake manifold. 2. Next, adjust the first and third valves on the side of the exhaust manifold, then rotate the engine crankshaft one more turn. 3. Then adjust the first and second valves on the intake manifold side counting from the rear. 4. Finally, adjust the first and third valves on the exhaust side. The following is an introduction to valves: The function of valves is to specifically input air into the engine and expel the exhaust gases after combustion. Structurally, they are divided into intake valves and exhaust valves. The intake valve's role is to draw air into the engine to mix with fuel for combustion, while the exhaust valve's role is to expel the burned exhaust gases and dissipate heat.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.