Why Don't Car Experts Buy Japanese Cars?

1 Answers
Cynthia
07/30/25 2:08am
Some people might think that car experts don't buy Japanese cars, but this view isn't entirely objective. Here's a breakdown: 1. Technical Analysis: Japanese cars are actually less sophisticated than European models in terms of engine structure. This is because Japanese automakers typically only incorporate technologies that have undergone extensive testing into mass-produced vehicles, meaning they predominantly use well-established, mature technologies. 2. Parts Supply: The parts supply chain also contributes to the durability and reliability of Japanese cars. Currently, apart from Europe, most top-tier component suppliers are concentrated in Japan. Additionally, Japanese automakers hold shares in these parts companies, allowing them to directly control part quality while maintaining low costs.
Was this review help?
3
2
Share
More Forum Discussions

How to Deal with Small Dents on Car Paint?

First, clean the dented area thoroughly, then load the special glue into the glue gun and plug it in to preheat for about 7 minutes. Next, select an appropriate backing plate, noting that larger dents require larger backing plates, as the larger the backing plate, the greater the traction force. Then, evenly apply the melted glue from the glue gun onto the backing plate, quickly press it onto the dented area, and hold it gently until the special glue sets firmly before releasing. Align the hole in the middle of the traction bridge with the backing plate, place the nut over the screw rod of the backing plate, and tighten it. Continue turning the nut until the dent is pulled out and leveled. After the repair is complete, remove the tools, spray alcohol on any residual glue on the car body, and finally clean it off with a scraper.
5
0
Share

What are the causes of steering system failure in BYD Qin?

Steering system failures are caused by issues such as steering gear malfunction and power steering pump failure. Specific faults: Oil leakage from the steering gear at the upper cover, side cover, and the connection point of the steering shaft arm, abnormal noises during steering, and oil leakage at the rear cover of the power steering pump can all lead to steering system failure. Solutions: The upper cover, side cover, and steering shaft are equipped with sealing rings. Replacing the oil seals and sealing rings can resolve steering gear issues. Oil leakage at the rear cover of the power steering pump is typically due to damaged sealing rings, which can be fixed by replacing the rear cover sealing ring. Abnormal noises during steering are often caused by damaged thrust bearings in the steering column. During inspection, turning the steering wheel left and right to locate the source of the noise can help identify the issue for disassembly and repair.
11
5
Share

What is the purpose of polishing?

The following are the functions of automotive polishing: 1. Used to reduce the surface roughness of the car, obtaining a bright and smooth surface. 2. Removes issues affecting the paint appearance such as the oxidation layer on the paint surface, shallow scratches, and loss of gloss caused by oxidation. Below are the methods for polishing different automotive issues: 1. Defect removal: Spray a small amount of water on the paint surface, use P1500 pyramid sandpaper with a dry grinder to sand the entire surface once in all directions (up, down, left, right) until the paint surface becomes matte; after sanding, use a rubber squeegee to scrape off the white foam on the surface, observe the paint surface to identify prominent defects, then spray a small amount of water on the sanding disc to remove the defects. 2. Overly fine paint surface: Use a dry grinder with P3000 pyramid sanding disc and a dry sanding soft pad to finely sand the overly fine paint surface, spray a certain amount of water on the sanding disc and paint surface, and sand the entire paint surface twice in each direction (up, down, left, right) at a faster speed. After sanding, use a rubber squeegee to scrape off the surface water and white foam. Quality standard: The paint surface should be free of defects such as oxidation layers and scratches. 3. Coarse wax polishing: Further removes surface sanding marks after sandpaper grinding, restoring the paint surface's smoothness and initial gloss. Apply wax evenly on a certain area of the paint surface, with the polisher speed controlled between 1200-2000 RPM. Initially, apply medium to high pressure to the polishing pad to polish the paint surface at a uniform speed. Observe the paint surface, and once the sanding marks are significantly removed, reduce the pressure to remove the wax marks, restoring some gloss to the paint surface. After polishing, use a microfiber cloth to clean off any residual coarse wax and dust from the paint surface.
9
3
Share

Driving Test Subject 3 Lighting Mnemonic Table?

Subject 3 lighting test mnemonic: 1. Driving at night without street lights and under poor lighting conditions; (high beam) 2. Meeting non-motor vehicles on narrow roads at night; (low beam) 3. Following vehicles closely in the same direction at night; (low beam) 4. Meeting motor vehicles at night (low beam) 5. Passing over arch bridges and pedestrian crossings at night; (alternate between high and low beams) 6. Passing sharp curves and slopes at night; (alternate between high and low beams) 7. Passing intersections without traffic signals at night; (high and low beams) 8. Vehicle breakdown on the road at night, obstructing traffic and difficult to move. (width lights, hazard warning lights) 9. Driving in foggy weather (fog lights, hazard warning lights) Summary: No lights turn on high beam, following or meeting vehicles use low beam, the word 'passing' means alternate between high and low beams.
4
0
Share

What to Do if There's a Small Cut on the Sidewall of a Tire?

If the sidewall of a tire is scratched, it must be replaced as soon as possible to avoid the risk of a high-speed blowout. If the damage on the contact surface exceeds 4mm, the tire should also be replaced immediately, as both internal and external repairs pose potential dangers. It is not recommended to use the vehicle before the tire is inspected and repaired (especially if the front tire is damaged). It is advisable to remove the tire to check for internal punctures. Considering safety, if this area is punctured, it is not recommended to repair it—replacement is necessary. The following five habits can extend tire life: 1. Develop the habit of checking tire pressure regularly. Air pressure is key to extending tire life—if tire pressure frequently exceeds the normal level by 20%, tire life will decrease by 10%; if it is frequently 30% below normal, tire life will be reduced by 52%. 2. Maintain consistent air pressure. Tire pressure is the life of a tire. If pressure is too low, the tire body deforms more, leading to cracks on the sidewalls and excessive heat generation, which accelerates rubber aging, fatigue of the cord layer, and cord breakage. 3. Regularly remove foreign objects from the tire. While driving, small stones often get lodged in the tread grooves. If not removed promptly, these stones can puncture the tire over time, causing leaks or blowouts. 4. Adopt scientifically sound driving habits. When driving on roads with significant curvature, try to stay centered to avoid and reduce vehicle weight shifts, which can increase uneven tire wear due to uneven load distribution. 5. Maintain accurate wheel alignment. Front-wheel alignment greatly impacts tire lifespan, with toe-in and camber being the primary factors. Excessive camber accelerates shoulder wear (uneven wear), while incorrect toe-in mainly accelerates wear on the inner and outer edges of the tire.
17
1
Share

What causes odors inside an Audi A4?

Audi A4 interior odors may be caused by sound insulation cotton, vibration damping pads, and interior materials. Solutions are as follows: Ventilation method: For the first six months after purchasing a new car or after decoration, develop the habit of moderately opening windows while driving to maintain fresh air circulation inside the vehicle. Chemical product method: Herbal formaldehyde remover, a general term for plant-based solutions, can be sprayed on floor mats and seats to decompose new car odors. Activated charcoal method: Place activated charcoal inside the new car. Higher-quality options include using Ye Guangni material, which can be reused. Vinegar method: When the car is not in use, place a small bucket of water with some vinegar inside the vehicle. The water can absorb formaldehyde while the vinegar helps stabilize it.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.