Why doesn't the window go down when pressed?

1 Answers
Steph
07/30/25 12:07am
Possible reasons generally include: 1. The window's mud slot is deformed or damaged. 2. The screws fixing the window regulator are loose. 3. The window regulator is damaged. 4. There is a deviation in the installation position of the guide rail. General solutions for car window glass lifting failure: 1. Turn on the ignition switch, hold the switch up and keep it pressed. 2. After the glass reaches the top, continue to hold the switch for more than 3 seconds, then release and immediately press and hold it again. 3. Let the glass descend to the bottom and wait for more than 3 seconds, then repeat the upward action once more. 4. The initialization procedure is completed, and the window lifting function is restored.
Was this review help?
9
0
Share
More Forum Discussions

What are the symptoms of a bad engine timing chain?

When the timing chain is faulty, it can cause engine noise, high fuel consumption, increased oil consumption, failure to start the car, lack of power, and severe exhaust emissions. The symptoms of timing chain failure and when it needs to be replaced are as follows: Symptoms of timing chain failure: Engine produces abnormal noise; High fuel consumption; Increased oil consumption; Car fails to start; Lack of power; Severe exhaust emissions. When the timing chain needs to be replaced: Check the elongation of the chain, replace if it exceeds the usable length; Inspect the wear of the car's camshaft and crankshaft sprockets, replace if it exceeds the usage limit; Examine the elongation, wear, or breakage of the timing chain, replace if damaged; Measure the thickness of the tensioner and chain damper, replace if it exceeds the usage limit.
3
3
Share

Where is the cabin air filter located in the BYD S6?

The cabin air filter in the BYD S6 is located beneath or inside the glove compartment on the passenger side. Failure to properly maintain the cabin air filter can lead to accumulation of dust and dirt on the filter screen, radiator, evaporator, and fin surfaces, resulting in airflow blockage. This may cause reduced cooling/heating efficiency, increased power consumption, noise issues, and shortened service life of the air conditioning system. Functions of the cabin air filter: 1. Adsorbs moisture, soot, ozone, odors, carbon oxides, SO2, CO2, etc. in the air; 2. Ensures clean cabin air free from bacterial growth, creating a healthy environment; 3. Effectively filters out solid impurities like pollen and abrasive particles, preventing allergic reactions that could compromise driving safety.
12
2
Share

What is the problem when a car revs by itself without stepping on the accelerator?

When a car revs by itself without stepping on the accelerator, it is mostly due to an issue with the idle motor. It is recommended to check the idle motor and clean the throttle body at the same time. If the car revs on its own without pressing the accelerator, the cause should be analyzed based on different situations. For electronic throttle systems, focus on checking the throttle and accelerator pedal. For cable-operated throttles, inspect the throttle cable and idle motor. Throttle issue: The throttle cable may not be returning properly, possibly due to insufficient lubrication. Solution: Remove the cable, pour lubricating oil from the upper end of the cable, and allow the oil to slowly penetrate into the cable tube. Idle motor problem. For example, the idle motor may be stuck or have lost its memory. Solution: Clean or replace it and then recalibrate. This requires initialization using a diagnostic computer.
4
5
Share

What to Do When Taking the Subject 2 Driving Test on a Rainy Day?

When taking the Subject 2 driving test on a rainy day, pay attention to the following: 1. Control your speed. Drive slower than your usual practice speed during rainy conditions. The examiner will also be concerned about driving safety, so prioritize safety over passing the test. 2. Maintain a safe distance. Keep a proper distance from the vehicle ahead during the test and avoid sudden braking. Instead, use gentle or intermittent braking to prevent test failure due to harsh stops. 3. Remember to turn on the windshield wipers. During practice, you might not use them often as the weather is usually good, but don’t forget to activate them on rainy test days. The wiper switch is located on the lower right side of the steering wheel, opposite the turn signal switch on the left. Adjust the wiper speed according to the intensity of the rain. 4. Stay calm. If you encounter rain during the Subject 2 test, adjust your mindset and remain composed, avoiding any negative impact from the weather.
11
2
Share

What are the causes of high pressure in car air conditioning?

The causes of high pressure in car air conditioning: 1. System blockage, mostly due to expansion valve blockage or malfunction, the solution is to replace the expansion valve; 2. Excessive refrigerant, the exhaust port feels hot to the touch and the suction port feels warm, normally these areas should feel cool, the compressor may occasionally make liquid impact sounds, the solution is to completely evacuate and quantitatively recharge the refrigerant; 3. Poor cooling of the condenser, the temperature of the pipeline from the condenser outlet to the expansion valve inlet feels hot to the touch, normally this section should feel warm, the solution is to clean the condenser and radiator grille of dirt, replace if necessary; 4. Expansion valve failure, the low-pressure pipe will have a large number of dew drops or frost, the solution is to check if the expansion valve is installed correctly, if correct, replace the expansion valve; 5. Other faults, such as cooling fan failure, engine overheating, excessive or insufficient refrigeration oil.
18
4
Share

The Impact of China VI Emission Standards on Used Cars

"China VI", fully known as the "China 6th Stage Emission Standard for Light-Duty Vehicles", is an emission standard system independently developed by China based on referencing emission standard systems from other countries and regions, combined with its own development realities. Due to its complexity and difficulty surpassing the "China V" standard, "China VI" is also referred to as the "world's strictest" emission standard within the industry. According to relevant regulations, the implementation of the "China VI" standard is divided into two phases: a and b. The first phase, starting from July 1, 2020, prohibits the sale, registration, and licensing of vehicles that do not meet the "China VIa" emission standard. The second phase, starting from July 1, 2023, prohibits the sale, registration, and licensing of vehicles that do not meet the "China VIb" emission standard.
20
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.