Why does the Tiida's collision avoidance system light flash?

1 Answers
ElliottLee
07/29/25 9:37am
Tiida's collision avoidance system light flashing is to remind the owner that there is an obstacle in front of the car, and it is necessary to pay attention to the speed not being too fast to avoid collision. The collision warning system can automatically detect the distance of obstacles ahead through sensors and estimate the possibility of a collision. If the system determines that the possibility of a collision is high, it will illuminate the collision warning system light through the sensors. Taking the Tiida TIIDA 2021 1.6L manual Ledong version as an example: the manufacturer of this car is Dongfeng Nissan, the level is compact car, the energy type is gasoline, the transmission is 5-speed manual, and the body type is 5-door 5-seat hatchback.
Was this review help?
17
0
Share
More Forum Discussions

What is the ground clearance of the new Bora?

The minimum ground clearance of the new Bora when fully loaded is approximately 122mm. The greater the minimum ground clearance, the stronger the vehicle's ability to pass over obstacles or uneven ground. Below is some information about minimum ground clearance: 1. Minimum ground clearance refers to the distance between the lowest protruding part of the vehicle's chassis and the level ground when the vehicle is fully loaded, reflecting the vehicle's ability to pass over obstacles or uneven ground without collision. 2. The greater the minimum ground clearance, the stronger the vehicle's ability to pass over obstacles or uneven ground, but the higher the center of gravity, which reduces stability. 3. The smaller the minimum ground clearance, the weaker the vehicle's ability to pass over obstacles or uneven ground, but the lower the center of gravity, which can increase stability.
11
3
Share

How to Set the Car Remote Control Lock Sound?

Depending on the car model, some models cannot adjust the sound volume when locking with the remote key, while others can set the sound to silent mode. The method to set the car remote key sound is as follows: 1. If the remote key has four buttons, there is usually an additional silent mode button. Pressing it will result in only the hazard lights flashing when locking the car, without the horn sound. 2. If the remote key has three buttons, you can try pressing the lock button. After the car beeps once, simultaneously hold down the unlock and lock buttons. The car will beep again, then press the unlock button, and the car will enter silent mode with only the hazard lights flashing and no horn sound.
12
4
Share

What Causes Car Gear Grinding?

The following are the reasons that cause car gear grinding: 1. Forcing the gear into place without depressing the clutch, or forcing the gear out without depressing the clutch. 2. Completely releasing the clutch before the gear shifting is completed, which will result in a gear grinding noise. 3. Try to avoid this as much as possible, as it will wear out the gears. 4. Clutch failure, which is a mechanical failure of the clutch that prevents it from disengaging properly, causing the gears to make a rattling noise. 5. Operational reasons, which means the clutch is not used correctly. In this case, attempting to engage the gear will result in a clicking noise and failure to engage. Shifting gears under these conditions can cause damage to the transmission.
9
0
Share

What is the reason why the Jaguar XEL does not beep when locking?

Jaguar XEL does not beep when locking may be due to accidentally pressing the mute button on the key or the lock mute function being enabled. Accidentally pressing the mute button on the key: When the owner presses the mute button, the vehicle will not have any prompt sound whether unlocking or locking. At this time, just press the lock mute button on the key again to enable the lock prompt sound. How to set the lock beep sound: Step on the brake pedal to start the vehicle, shift the gear to the P position and pull up the vehicle's handbrake; close all four doors and the trunk of the vehicle; press the mute button on the key inside the car, and the vehicle will have a lock prompt sound the next time it is locked.
13
0
Share

Are Bestune and Great Wall from the same manufacturer?

Bestune and Great Wall are not from the same manufacturer. FAW-Volkswagen Automotive Co., Ltd.: (Abbreviation: FAW-Volkswagen) was established on February 6, 1991. It is a large passenger vehicle production enterprise jointly operated by China FAW Group Corporation, Volkswagen AG, Audi AG, and Volkswagen (China) Investment Co., Ltd. It is the first modern passenger vehicle industrial base in China constructed according to economic scale. Bestune: FAW Car Co., Ltd. (Abbreviation: FAW Car) is a holding subsidiary of China FAW Group Corporation, established through the restructuring of high-quality assets primarily engaged in the production of Hongqi sedans and their components by FAW Group Corporation. As a brand parallel to "Hongqi" under FAW Car, Bestune made its debut on May 18, 2006.
1
3
Share

Where is the CD player installed in the Volkswagen Touareg?

The CD player in the Volkswagen Touareg is located in the drawer in front of the passenger seat. There is a yellow clip on it, and you can pull it down. Functions of the CD player buttons: BAND - Radio band, CENTER - Front center (speaker), MODE - Mode selection, LOUD - High volume, SETUP - Settings, MUTE - Mute, TITLE - Title. Precautions for using the CD player: Since the mechanism of the built-in CD player is relatively delicate, the space is small, and the precision is high, improper use can easily cause the CD to get stuck, especially in built-in multi-disc CD players. Of course, with proper use, the CD player is not so prone to getting stuck.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.