Why does the steering wheel light stay on and the car won't start?

1 Answers
StHarmony
07/25/25 3:11pm
This indicates that the vehicle's emergency anti-theft system has been activated. The anti-theft system is a car security lock designed to immobilize the steering wheel, consisting of a lock rod, lock body, and lock handle. Engine immobilizer system: Each key contains an embedded transponder. When the driver inserts the key into the ignition switch cylinder and turns it to the "ON" position, the electronic anti-theft ECU communicates with the key via radio frequency. If the key is verified as legitimate, the anti-theft ECU will then perform password authentication with the engine ECU. If the password is correct, the engine will be allowed to start. Classification of vehicle anti-theft systems: Mechanical anti-theft, electronic anti-theft, and network-based anti-theft.
Was this review help?
19
0
Share
More Forum Discussions

What is the replacement standard for brake disc wear?

The replacement standard for brake disc wear is when the wear exceeds 2 millimeters. The replacement steps are as follows: 1. Open the engine compartment and check if the brake fluid level is at the normal position to avoid overflow during the brake pad replacement process; 2. Use a jack to align with the support points under the car, raise the car until the tire is completely off the ground, and then remove the tire; 3. Use a wrench with a socket to remove the bolts of the brake caliper and directly take off the brake pads; 4. Push the brake piston back to its original position and install the new brake pads; 5. After installation, check the brake fluid level, press the brake pedal firmly several times, and then add brake fluid again to ensure the fluid level is at the max mark.
8
0
Share

What Causes Acceleration Shaking?

Acceleration shaking is caused by excessive carbon buildup in the throttle body, intake tract, and valve areas, which leads to an overly rich air-fuel mixture during engine idling, resulting in unstable idle. Solutions for acceleration shaking: 1. Severe carbon buildup in the engine or idle control valve - clean the fuel system; 2. Ignition system issues - check if spark plugs have excessive carbon buildup and replace them if necessary; 3. Unstable fuel pressure - inspect fuel pressure and replace corresponding components; 4. Aging engine components - replace worn parts. Functions of the engine: 1. Fully burn the fuel introduced into the cylinders to generate power; 2. Determine the vehicle's power performance, fuel economy, stability, and environmental friendliness.
9
0
Share

What Gear Should an Automatic Car Be in When Waiting at a Red Light?

When waiting at a red light, an automatic car should be shifted into N (Neutral) gear. The correct usage methods for an automatic transmission are: 1. The vehicle can only be started in P (Park) or N (Neutral) gear. To shift out of P gear, the brake must be pressed. Turn on the power, press the brake, shift to N gear, and after ignition, shift to D (Drive) gear to move forward directly; 2. When switching between N, D, and 3 gears, there is no need to press the shift button. However, shifting from 3 gear to lower restricted gears requires pressing the shift button, while shifting from lower to higher gears does not; 3. Do not shift into N gear while driving to coast; 4. Never push into P gear while driving; 5. After driving, the engine must be turned off and shifted into P gear before the key can be removed.
5
5
Share

What are the reasons why the Great Wall H6 cannot start with one-key ignition?

The reasons why the Great Wall H6 cannot start with one-key ignition are: 1. The low-intensity radio waves in the key are interfered with: often placing the car key near electronic devices such as computers or TVs, or in areas with strong radio waves, such as TV towers, airports, or power plants; 2. The car key battery is dead: the key shows symptoms like shortened remote control distance or reduced sensitivity; 3. Vehicle malfunction: issues such as fuel system problems, dead battery, or short circuits in electronic components. Solutions for the failure to start include: 1. Replace the key battery; 2. Charge the battery promptly or replace it with a new one to avoid insufficient power; 3. Park the car in a warm environment; 4. Use engine oil suitable for the current temperature conditions; 5. Increase the frequency of car use to expel accumulated water in the exhaust pipe with stronger exhaust force; 6. Add antifreeze; 7. Regularly remove carbon deposits from the valves; 8. Clean the spark plugs; 9. Clean the fuel system.
3
3
Share

Where is the qr25 engine produced?

qr25 engine is produced in Japan. The functions of the engine: 1. Fully combust the fuel input into the cylinder to generate power; 2. Determine the vehicle's power, fuel economy, stability, and environmental performance. Engine maintenance methods: 1. Use qualified engine oil; 2. Use qualified coolant; 3. Regularly clean the water tank scale; 4. Regularly remove carbon deposits from the engine; 5. Replace the vehicle's air filter, oil filter, and fuel filter on time; 6. Check the condition of the spark plugs; 7. Maintain normal engine speed. The working principle of the engine: 1. Mix air and gasoline in a certain proportion to form a combustible mixture; 2. The intake stroke draws the mixture into the cylinder, where it is compressed, ignited, and burned to produce thermal energy; 3. The high-temperature and high-pressure gas acts on the top of the piston, pushing the piston to perform reciprocating linear motion, and the mechanical energy is output externally through the connecting rod, crankshaft, and flywheel mechanism.
19
0
Share

How to Use the Lights on Arrizo 5

To use the lights on the Arrizo 5: 1. Activate automatic headlights: Turn the knob at the end of the control lever to 'off' to turn off all lights, then turn it to 'auto'. 2. Turn on the turn signals: Push the lever counterclockwise past the resistance point for the left turn signal to flash, or clockwise past the resistance point for the right turn signal to flash. For lane changes, quickly push the lever left or right without passing the resistance point, and the turn signal will flash 3 times before turning off. 3. Turn on the parking lights and low beams: Turn the knob at the end of the control lever up one position to activate the parking lights and license plate lights, and up two positions to activate the low beams. 4. Turn on the high beams: When the low beams are on, push the control lever away from the steering wheel past the resistance point to switch to high beams. Pulling the lever toward the steering wheel and holding it will keep the high beams on, while releasing it will return to low beams. 5. Turn on the fog lights: With the low beams or parking lights on, turn the inner knob on the control lever up one position to activate the rear fog lights.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.