Why does the one-button start motor of the new Tiida not start?

What to Do When Turn Signals and Hazard Lights Don't Work?

If both the turn signals and hazard lights are not working, it is recommended to promptly check the vehicle's light switch and wiring harness for any short circuits. If necessary, visit a 4S shop for repairs as soon as possible. The solutions for non-functioning turn signals and hazard lights are as follows: 1. Check if the power line terminal of the flasher relay has electricity. If there is no power, inspect whether there is a break in the line to the power source. 2. If there is power, use a screwdriver to connect the two terminals of the flasher relay. If the turn signals light up, it indicates a fault in the flasher relay, which should be replaced. If they do not light up, inspect the flasher relay. Open the flasher relay cover and check if the coil and resistor are intact. If the resistor heats up and the contacts cannot close, press the movable contact; if the turn signals light up at this point, it indicates a fault in the relay. Adjust the contact gap if it is too large. If the turn signals still do not light up when pressing the movable contact to close the contacts, use a screwdriver to short-circuit the contacts. If the lights turn on, it indicates oxidation of the contacts. 3. If the turn signals do not light up when short-circuiting the two terminals of the flasher relay with a screwdriver, the issue may lie with the turn signal switch. During inspection, use a screwdriver to connect the power line of the turn signal switch to the left and right light line terminals separately. If the lights turn on, it indicates a fault in the turn signal switch, which should be removed for repair or replacement.

16

3

Share

How to Set Up the Anti-Pinch Feature for BMW 5 Series Windows?

First, turn on the ignition switch, then lift each window switch to the top and hold for more than 3 seconds, then lower it to the bottom and hold for more than 3 seconds. Below is some relevant information about the BMW 5 Series: 1. The programmable instrument panel, B&Q premium audio system, upgraded third-generation iDrive, iPhone voice interaction system, and mocha and ivory white Nappa leather seats are among the interior changes in the new 5 Series. These changes are mainly focused on details, with little overall variation. 2. The new BMW 5 Series has upgraded its ConnectedDrive system, with features like lane departure warning, frontal collision warning, pedestrian collision protection, and a night vision system with animal recognition, all enhancing the car's safety. The newly added convenient opening and closing function for the trunk also improves the ease of use for the trunk.

4

1

Share

Is the Fit from Dongfeng Honda or GAC Honda?

The Honda Fit is a compact hatchback under GAC Honda and does not belong to Dongfeng Honda. Here is an introduction to the third-generation Fit: 1. The third-generation Honda Fit was launched on May 29, 2014, as a compact hatchback introduced by Guangzhou Honda, positioned as the "Cool Hatchback" in its third generation. The third-generation Fit was the first to be equipped with Honda's new (Earth Dreams Technology) engine. 2. The new 1.5L direct-injection engine delivers a maximum power of 96kW/6600rpm and a maximum torque of 155N·m/4600rpm, ranking first in its class in terms of power performance. It is paired with a new CVT continuously variable transmission.

15

1

Share

How to Use a Prado During the Break-in Period?

During the break-in period of a Prado, it is essential to start in a low gear and avoid sudden acceleration. Shift to a higher gear promptly after starting. Do not drive in first gear or high gear for extended periods. Avoid pushing the engine speed and vehicle speed to their limits in any gear. It is best to keep the engine speed below 3,000 RPM and the speed under 120 km/h. Additional Information: Precautions During the Break-in Period: 1. Warm Up Before Starting: Before starting, turn the key to the second position and wait for 5-10 seconds before ignition. This is because the fuel pump begins working when the ignition is turned on, adjusting fuel pressure and injection volume. Starting after a few seconds helps protect the new engine. 2. Avoid Emergency Braking: Emergency braking not only shocks the braking system during the break-in period but also increases the impact load on the chassis and engine. It is advisable to avoid emergency braking within the first 300 kilometers of driving. 3. Avoid Overloading: Overloading a new car during the break-in period can damage components. Therefore, within the first 1,000 kilometers, domestic cars should not exceed 75%-80% of the rated load, and imported cars should not exceed 90% of the rated load. Additionally, choose smoother road surfaces to reduce stress on the body and powertrain, avoiding vibrations, collisions, or emergency braking. 4. Avoid High-Speed Driving: New cars have speed limits during the break-in period. Domestic cars are generally limited to 40-70 km/h, while imported cars are limited to 100 km/h. When the throttle is fully open, the speed should not exceed 80% of the maximum speed. Monitor the engine tachometer and speedometer to ensure the engine and vehicle operate at moderate speeds. Typically, the engine speed during the break-in period should be between 2,000-4,000 RPM.

6

1

Share

Differences Between SUVs and Sedans

Differences between sedans and SUVs: 1. Chassis: Sedans have a lower chassis, which results in a lower center of gravity, leading to smaller vehicle tilt angles during turns; SUVs have a higher chassis, allowing them to adapt to various road conditions. 2. Seat comfort: SUVs lean towards a sporty style, so their seats are designed to be firmer; sedans prioritize passenger comfort, hence their seats are generally softer. 3. Fuel consumption: SUVs often consider off-road capabilities, making them heavier in design compared to sedans, and they typically have larger engine displacements, resulting in higher fuel consumption under similar conditions.

18

0

Share

What to Pay Attention to When Making a Left Turn While Driving

Precautions for making turns while driving: 1. Wide turning radius: When making a left turn, try to turn as widely as possible. To avoid hazards such as obstruction or collision, aim to turn into a farther point. 2. Check the rearview mirror: Always check the rearview mirror before turning to ensure there are no vehicles or pedestrians on the side or behind you. 3. Watch for blind spots: Beginners often focus only on the front or left side while turning, neglecting blind spots, which may lead to hitting the curb or causing a scrape. Always check for obstacles below the rearview mirror, and if necessary, open the door to take a look before turning. 4. Control the steering wheel: Proper steering wheel control is crucial when turning. For sharp turns, turn the wheel as much as needed and gradually straighten it after completing the turn. For wide turns, steer slowly and steadily.

16

5

Share

Why does the one-button start motor of the new Tiida not start?

What to Do When Turn Signals and Hazard Lights Don't Work?

How to Set Up the Anti-Pinch Feature for BMW 5 Series Windows?

Is the Fit from Dongfeng Honda or GAC Honda?

How to Use a Prado During the Break-in Period?

Differences Between SUVs and Sedans

What to Pay Attention to When Making a Left Turn While Driving

What to Do When the Highlander Won't Start?

Is there a difference between the high and low power versions of Volkswagen's 1.4T engine?

Why does the antifreeze level decrease during use?

How much fuel is needed to fill up the Audi Q3's fuel tank?