Why does the Kia K5 suddenly fail to start?

1 Answers
StAndres
07/30/25 4:35am
Kia K5 suddenly failing to start is due to a dead battery. A battery generally refers to all chemical energy batteries that can be recharged and reused after being discharged to a certain extent. The Kia K5 has a length, width, and height of 4855mm, 1835mm, and 1475mm respectively, with a wheelbase of 2805mm and a minimum ground clearance of 145mm. This car is equipped with a 2.0L naturally aspirated engine, with a maximum power of 115kW and a maximum torque of 189Nm, paired with a 6-speed automatic manual transmission. It adopts a front suspension type of MacPherson independent suspension and a rear suspension type of multi-link independent suspension.
Was this review help?
19
5
Share
More Forum Discussions

Where is the memory card for the Binyue dash cam located?

The memory card for the Binyue dash cam is located under the front passenger seat. The Binyue is a compact 5-door, 5-seat SUV with the following dimensions: length 4330mm, width 1800mm, height 1609mm, wheelbase 2600mm, and a fuel tank capacity of 45 liters. The Binyue is equipped with a 1.4T turbocharged engine and a 6-speed manual transmission, delivering a maximum power of 104 kW at 5200 rpm and a maximum torque of 235 N·m between 1600 to 4000 rpm. It features front-wheel drive, with a MacPherson strut independent front suspension and a torsion beam non-independent rear suspension.
13
4
Share

Should car maintenance follow the maintenance manual or the 4S shop?

Car maintenance should follow the maintenance manual. Below are relevant introductions about car maintenance: 1. First maintenance: Some manufacturers will determine the first maintenance based on time or mileage. The specific and accurate first maintenance time should be based on the vehicle user manual or warranty manual. The first maintenance is very important and free, so be sure to remember to do it to avoid missing the first maintenance and affecting the car's three-guarantee issues. 2. Maintenance items: The main maintenance items for car maintenance include replacing engine oil, oil filters, transmission oil, spark plugs, air conditioning filters, air filters, brake fluid, etc. However, not all items need to be replaced every time, as it depends on their service life. In addition, maintenance also involves inspection and maintenance of dozens of items across multiple systems such as the engine, transmission, air conditioning system, steering system, braking system, suspension, body, and tires.
10
5
Share

Where is the computer port of Citroen c4l?

Citroen c4l computer port is above the USB port in the center console. Citroen c4l is a compact 4-door 5-seater sedan with a body size of 4675mm in length, 1780mm in width, 1500mm in height, a wheelbase of 2710mm, and a fuel tank capacity of 60 liters. The Citroen c4l is equipped with a 1.6T turbocharged engine and a 6-speed automatic manual transmission, with a maximum power of 123 kilowatts and a maximum torque of 245 Newton meters. It adopts front-wheel drive, with front suspension using McPherson independent suspension and rear suspension using torsion beam non-independent suspension.
6
1
Share

What are the components of a drive axle?

The components of a drive axle include the main reducer, differential, wheel transmission device, and drive axle housing. The drive axle is a mechanism located at the end of the transmission system that changes the speed and torque from the transmission and transmits them to the drive wheels. The functions of the drive axle are: 1. To transmit the engine torque from the universal drive device to the drive wheels through the main reducer, differential, and half-shafts, achieving speed reduction and torque increase; 2. To change the direction of torque transmission through the bevel gear pair of the main reducer; 3. To enable differential action between the two wheels through the differential, ensuring that the inner and outer wheels turn at different speeds; 4. To bear loads and transmit torque through the axle housing and wheels.
17
3
Share

Where is the best place to install an ETC device?

For small cars, the ETC device is generally installed in the upper middle part of the front windshield, while for large vehicles such as trucks and buses, the installation position is in the lower middle part. The appropriate installation position should be no less than 1.2 meters and no higher than 2.5 meters in height, with an installation angle between 30 and 90 degrees. For vehicles with anti-explosion film or those that have it installed later, which may affect the signal transmission of the microwave communication link, the device should be installed in the microwave skylight strip. ETC stands for Electronic-Toll-Collection, meaning electronic toll collection system. To apply for ETC, the vehicle owner needs to provide original and photocopies of their valid ID card and vehicle registration certificate. If the application is not made by the owner themselves, the agent must also bring their valid ID card. The photocopy of the vehicle registration certificate should include the page with the most recent annual inspection seal. Additionally, a bank card for deducting highway tolls is required, and the vehicle must be registered under an individual aged between 18 and 60. Here are some precautions for installing ETC: Do not obstruct the view; it is best to install it behind the rearview mirror: Many car models have windshields with a large rearward tilt angle, which can reduce the driver's field of vision. If this is not considered during ETC installation, it may increase the driver's blind spots. Installing it behind the rearview mirror on the right side can help avoid obstructing the view. Do not interfere with charging: The ETC electronic tag consumes power but generally does not require charging or battery replacement because it has a solar panel on the back that can charge itself. Therefore, during installation, avoid the black areas on the windshield and positions that may block the solar panel. Once installed, do not remove it arbitrarily: The button in the middle of the adhesive is an anti-removal lever connected to a switch. After the electronic tag is installed, the windshield will press the anti-removal lever in. If the tag is removed arbitrarily, the lever will pop out and trigger the switch, locking the electronic tag and rendering it unusable. In such cases, you will need to visit an ETC service point to unlock it. This mechanism is designed to prevent multiple vehicles from sharing one device. When using ETC, note the following: The ETC transaction sensing range is 8 meters. To prevent the ETC device of the vehicle in front from malfunctioning, maintain a distance of more than 10 meters from the vehicle ahead to avoid automatic toll payment for the front vehicle. The ETC lane recognition speed is 20 kilometers per hour; driving too fast may result in failure to read the vehicle's device information and thus failed toll deduction. When using a debit card linked to ETC, insufficient balance may also cause toll deduction failure.
11
2
Share

How to Adjust the Rearview Mirror on a BMW 5 Series?

To adjust the rearview mirror on a BMW 5 Series, simply toggle the mirror adjustment switch to the left or right. Taking the 2021 BMW 525li as an example, it is a mid-to-large-sized 4-door 5-seater sedan with the following dimensions: length 5106mm, width 1868mm, height 1500mm, and a wheelbase of 3105mm. The 2021 BMW 525li is equipped with a 2.0T turbocharged engine and an 8-speed automatic transmission, delivering a maximum power of 135 kW and a maximum torque of 290 Nm. It features a rear-wheel-drive layout, with a double-wishbone independent suspension at the front and a multi-link independent suspension at the rear.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.