Why Does the Instructor Get Angry When the Engine Stalls?

1 Answers
Holly
07/29/25 9:09pm
The reason the instructor gets angry when the engine stalls is due to frustration over unmet expectations. Below are relevant details about the driver's test: 1. Definition: The driver's test (motor vehicle driver's test) is a qualification examination organized by the Vehicle Management Office of the Public Security Bureau. Only by passing this test can one obtain a driver's license and legally operate a motor vehicle. 2. Test Content: The motor vehicle driver's test is divided into the following sections: Road Traffic Safety Laws, Regulations, and Related Knowledge Test (also known as the 'Theory Test', referred to as 'Subject 1'), Site Driving Skills Test (commonly known as 'Pole Test', referred to as 'Subject 2'), and Road Driving Skills and Safe & Civilized Driving Knowledge Test (commonly known as 'Road Test', referred to as 'Subject 3'). The test content and passing standards are uniform nationwide, with corresponding test items specified for different types of vehicles eligible for driving.
Was this review help?
8
0
Share
More Forum Discussions

What are the symptoms of a failed car charcoal canister?

The symptoms of a failed car charcoal canister are: 1. Weak acceleration; 2. Abnormal noises while driving; 3. Fuel leakage in the pipeline; 4. Difficulty starting the engine; 5. Engine stalling. The causes of a failed car charcoal canister are: 1. Overfilling the fuel tank; 2. The activated charcoal canister is installed under the car, where the chassis environment is harsh; 3. Poor quality of the activated charcoal canister or internal filter cotton. The car charcoal canister is a container filled with activated carbon, also known as the automobile fuel evaporation emission control device. Its functions are: 1. Adsorbing fuel vapor generated by the temperature difference between day and night in the fuel tank after parking; 2. Absorbing fuel vapor produced during refueling.
4
0
Share

How long is the Passat body?

The overall length of all Passat models is 4933 mm, with a width of 1836 mm, height of 1469 mm, and a wheelbase of 2871 mm. Below are the specific details of the Passat: 1. Introduction: This model is a sedan produced by SAIC Volkswagen. It is manufactured by SAIC Volkswagen Automotive Co., Ltd. It features four doors, five seats, a fuel tank capacity of 68.5 liters, and a trunk capacity of 521 liters. 2. Powertrain: The vehicle adopts a front-engine, front-wheel-drive layout. It uses a MacPherson strut independent suspension at the front and a multi-link independent suspension at the rear. The steering assistance is electric power steering, and it features a unibody construction. It is equipped with either a 1.4-liter turbocharged engine or a 2.0-liter turbocharged engine.
20
1
Share

What are the differences between Golf 6 and Golf 7?

The differences between Golf 6 and Golf 7 are: 1. Different body dimensions: The Golf 6 has a length, width, and height of 4199mm, 1786mm, and 1479mm respectively, with a wheelbase of 2578mm; the Golf 7 measures 4259mm in length, 1799mm in width, and 1476mm in height, with a wheelbase of 2637mm. 2. Different suspension configurations: The Golf 6 features an independent suspension, while the Golf 7 uses a torsion beam non-independent suspension. 3. Different powertrains: The Golf 6 is equipped with an EA111 engine, delivering a maximum power of 96 kW and a maximum torque of 220 Nm; the Golf 7 comes with an EA211 engine, offering a maximum power of 110 kW and a maximum torque of 250 Nm.
11
2
Share

What is the pin configuration of a car's OBD interface?

Taking the Volkswagen New Passat as an example, the OBD diagnostic interface has 16 pins. Pin 16 is the constant power line. Pins 4 and 5 are ground wires. Pin 1 is the 15a ignition switch control line. Pin 7 is the K diagnostic wire. Pins 2, 3, 6, and 8 are CAN high bus lines. Pins 9, 10, 11, and 14 are CAN low bus lines. Pin 15 is the airbag diagnostic line. Pins 12 and 13 are empty positions. More details are as follows: 1. OBD is the abbreviation for On-Board Diagnostics, which translates to "on-board automatic diagnostic system" in Chinese. 2. This system continuously monitors the engine's operating conditions to check if the vehicle's emissions exceed the standard. If they do, it will immediately issue a warning.
3
0
Share

How to Deal with Slightly Deformed Wheel Hubs?

The method to handle slightly deformed wheel hubs is to perform dynamic balancing for the vehicle. The steps are as follows: 1. Remove and clean the tire, then take off the old balancing weights; 2. Place the tire on the dynamic balancing machine and secure it with clamps; 3. Measure the required values for the dynamic balancing machine; 4. After the tire stops, the dynamic balancing machine will display the deviation value of the tire; 5. Rotate the tire by hand. When the dynamic balancing machine shows full bars on both the inner and outer sides, add balancing weights according to the corresponding values. Dynamic balancing refers to the operation of determining the position and size of the unbalanced amount generated when the rotor rotates and eliminating it. The unbalanced amount can cause lateral vibration of the rotor, subjecting it to unnecessary dynamic loads and adversely affecting its normal operation.
8
0
Share

What are the consequences of a faulty EGR valve in a common rail fuel injection system?

The consequences of a faulty EGR valve in a common rail fuel injection system are: 1. Difficulty in engine starting and weak acceleration; 2. Failure to meet emission standards; 3. Black smoke from the vehicle's exhaust pipe; 4. Unstable idle or stalling at idle; 5. Flashing of the malfunction indicator light; 6. Burning of engine oil. Methods to clean the EGR valve in a common rail fuel injection system are: 1. Spray carburetor cleaner into the intake passage; 2. Spray carburetor cleaner onto the throttle body. The EGR valve is a mechatronic product installed on diesel engines to control the amount of exhaust gas recirculated back to the intake system, located on the right side of the intake manifold near the throttle body.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.