Why does the Haval M6's door not lock and the car light keeps flashing?

1 Answers
StZoey
07/30/25 3:19am
It indicates that the trunk is not properly closed. The flashing will stop after getting out of the car and closing it properly. When the lock button on the smart key is pressed, the car's anti-theft system will activate, and then the anti-theft light will flash. This serves as a reminder that the vehicle's anti-theft system is activated and the vehicle is in a secured state. The car's anti-theft light: If the car engine's anti-theft light flashes at a frequency of once every 1 to 2 seconds, it is normal. This indicates that the car's engine has entered the anti-theft state, and the engine anti-theft system has started working. This is a normal phenomenon, and the owner does not need to deactivate it. Moreover, the power consumption is minimal, and it poses no problem to the battery. The battery may be dead; If the battery is dead, the vehicle's anti-theft system will lock the vehicle, making it impossible to deactivate the anti-theft system, open the door, or start the engine via the remote control. You need to use the mechanical lock to open it and either jump-start or replace the battery.
Was this review help?
4
0
Share
More Forum Discussions

What is the Difference Between Honda Hybrid and Toyota Hybrid?

Honda Hybrid and Toyota Hybrid differ in the following aspects: Different Systems: Honda's hybrid system utilizes electric drive technology, which minimizes intermediate conversion processes during operation to maximize power output. Compared to Toyota's hybrid model, Honda's hybrid vehicles offer stronger power and better fuel efficiency, achieving both environmental friendliness and fuel economy. While many drivers may not notice the difference during daily use, a side-by-side comparison reveals significant disparities. Driving Methods: Their driving methods differ, but the outcomes are the same—both reduce exhaust emissions, mitigating atmospheric pollution and slowing the depletion of petroleum resources. Each of these two brands' hybrid models has its own unique advantages, and the choice ultimately depends on the owner's personal preference.
9
0
Share

What Causes Wind Noise from Car Windows Without Actual Air Leakage?

Wind noise from car windows without actual air leakage can be attributed to the following reasons: Loose Door Seals: It is highly likely that the wind noise is caused by loose door seals. For this issue, it is recommended to thoroughly inspect the sealing performance of the door rubber seals to check for any deformation or improper installation that might compromise the seal. Such issues can be addressed with free repairs during the vehicle's warranty period. Therefore, it is advisable to promptly visit a 4S dealership for further on-site inspection and diagnosis by a technician. Solution: Lower the window glass and press down on the upper right corner of the seal near the door frame. A small hole will appear, and this is where the wind enters, causing the wind noise. Roll 3M double-sided tape into small xylitol-sized pieces and gradually fill the hole until it is completely packed. This should resolve the issue.
17
0
Share

What is the reason for not hearing the fuel pump sound when turning the key?

The reasons for not hearing the fuel pump sound when turning the key are as follows: Fuel pump damage: The fuel pump is damaged. The fuel pump does not start, and no oil pressure is established. During secondary ignition, the crankshaft sensor forcibly starts the pump. The function of the fuel pump is to draw gasoline from the fuel tank and press it through the pipeline and fuel filter to the float chamber of the carburetor. Insufficient fuel: First, check whether the fuel level is sufficient and see if the fuel pump can draw fuel. If the fuel level is sufficient, check the fuel pump fuse. If the fuse is not broken, it is recommended to go to a 4S service station to check the fuel line, not the clogged fuel filter.
8
5
Share

What is the problem when the rear car cannot stop?

The reason why the rear car cannot stop may be due to a lack of necessary maintenance of the braking system, or mechanical failure caused by improper operation. Brief introduction to the causes of brake failure: There are many reasons for brake failure. First, it could be due to a lack of necessary maintenance of the braking system, such as excessive impurities in the brake master cylinder, poor sealing, failure of the vacuum booster, dirty brake fluid or the formation of vapor locks when different types of brake fluid are mixed and heated, leakage in the brake master cylinder or wheel cylinders, or air leaks in the air reservoir or pipeline connections. Second, improper operation may lead to mechanical failure, such as prolonged downhill driving causing the brake pads to overheat, carbonization of the brake drums, and complete loss of braking function. Third, severe overloading increases the vehicle's inertia due to gravitational acceleration, directly resulting in brake failure. How to handle brake failure while driving: Control the direction according to the road conditions and speed, disengage the high gear, and quickly rev the engine once to shift from high gear to low gear. This will create significant engine braking resistance, rapidly reducing the vehicle's speed. Additionally, while shifting to low gear, use the handbrake in combination, but be careful not to pull it too tightly or too slowly. Pulling it too tightly may cause the brake disc to "lock up," potentially damaging the transmission components and losing braking ability. Pulling it too slowly may cause excessive wear and overheating of the brake disc, rendering it ineffective. Use the vehicle's rigid parts, such as the bumper or body, to rub or collide with natural obstacles on the roadside (rocks, large trees, or slopes) to force a stop and minimize accident losses.
1
1
Share

What are the reasons for a heavy steering wheel in the Teana?

The reasons for a heavy steering wheel in the Teana are as follows: Power steering pump failure: When the pump pressure of the power steering pump fails to meet the standard value, the steering wheel will feel heavy during use. It is necessary to inspect the flow control valve. If there is leakage in the flow control valve or safety valve during driving, it can be repaired by grinding. Then, check whether the spring of the safety valve has failed. Steering gear failure: When the hydraulic pressure of the steering gear is low, the steering will feel heavy. If the steering wheel becomes heavy due to the hydraulic pressure of the steering gear, it is necessary to seek professional repair from a specialized manufacturer. It is not recommended for the car owner to handle it themselves. Lack of oil or air in the power steering system: When there is air in the car's steering system, not only will the steering feel heavy, but there will also be noise during steering. This needs to be addressed promptly to avoid greater losses. Clogged return oil filter in the oil reservoir: If the return oil filter in the oil reservoir is not maintained or replaced for a long time, it can easily become clogged, leading to poor circulation of the power steering oil and a heavy steering wheel.
6
5
Share

What Are the Procedures for Professional Car Washing?

Professional car washing consists of four procedures. Vacuuming and tidying up interior items: The first step of cleaning should be to remove dust from the interior of the car, sweep away large debris, and then use a vacuum cleaner to suck up dust from the carpets and gaps between seats. Cleaning the control compartment: The dashboard and steering wheel are mostly made of plastic and leather, which easily attract dust but are also relatively easy to clean. It is important to note that since the dashboard is exposed to sunlight for long periods, it is prone to aging and becoming brittle. Therefore, it is best to choose a high-quality dashboard wax to spray, then wipe it clean with a dry cloth to properly protect the dashboard. Cleaning the air conditioning ducts: Remove the air conditioning vents, insert the thin tube of the air conditioning cleaner into the ducts, and spray an appropriate amount of cleaner. Then close the vents, turn on the air conditioning's internal circulation, start the engine, and let it idle for about 10 minutes. Also, clean the air conditioning filter. Cleaning the seats: When cleaning seats made of velvet or other fabric materials, spray high-efficiency foam cleaner onto the stains, let it sit for a while, and after the foam is completely absorbed, wipe carefully with a clean dry towel repeatedly until the stains are removed.
10
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.