Why does the Geely Binyue require 6 liters of engine oil?

1 Answers
LeOscar
09/08/25 2:22am
Geely Binyue's 1.5T engine requires approximately 5.5 liters of engine oil, but since there are no oil packages available in this exact specification, a full 6 liters must be used at a time. Precautions for adding engine oil to the Binyue: When adding engine oil, ensure that the oil level is between the min and max marks on the dipstick. The oil level should neither be below the min mark nor exceed the max mark. If it is below the min mark, it may lead to insufficient lubrication, which can accelerate engine wear. If it exceeds the max mark, it can increase the engine's operational resistance, resulting in reduced power and higher fuel consumption. Functions of engine oil: Lubrication to reduce wear: Between the engine's pistons and cylinders, as well as between the main shaft and bearings, there is rapid relative sliding, which can cause wear. High-quality engine oil forms a sufficiently thick oil film between these sliding surfaces, separating the moving parts and thereby reducing wear. Cooling: Engine oil carries heat back to the oil pan and dissipates it into the air, assisting the radiator in cooling the engine. Cleaning: Good engine oil can circulate carbon deposits, sludge, and worn metal particles from engine components back to the oil pan, flushing away contaminants generated on the working surfaces of the parts through the flow of the lubricant.
Was this review help?
12
5
Share
More Forum Discussions

Where is the coolant temperature gauge on the Rena?

The Rena does not have a coolant temperature gauge, only a temperature warning system is retained. Taking the 2020 Rena as an example, it belongs to the subcompact car category with body dimensions of: length 4300mm, width 1705mm, height 1460mm, wheelbase 2570mm, fuel tank capacity 43L, and curb weight 990kg. The 2020 Rena features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.4L naturally aspirated engine producing maximum power of 95PS (70kW) and maximum torque of 132.4Nm, paired with a 5-speed manual transmission.
14
0
Share

How to Identify Car Gears?

P (Park), R (Reverse), N (Neutral), D (Drive), S (Sport Mode), L (Low Gear). Below is a detailed introduction to car gears: 1. P Gear is the Parking Gear: When the gear lever is in the P position, the transmission is in neutral internally, but the output shaft is mechanically locked. At this time, the car will stop in place even without stepping on the brake, and it is generally used for long-term parking of the car. When engaging the P gear, the car must be completely stationary. Do not engage the P gear when the car is not fully stopped, and always apply the handbrake. When parking on a slope, you need to apply the handbrake first and then engage the P gear. 2. R Gear is the Reverse Gear: When the gear lever is in the R position, the rotation direction of the transmission output shaft is opposite to that of the engine, allowing the car to move backward. When engaging the R gear, the car must be completely stationary. Do not engage the R gear when the car is not fully stopped. 3. N Gear is the Neutral Gear: When the gear lever is in the N position, the gears inside the transmission are in an idle state, and the clutch is not engaged. The load on the transmission is minimal at this time. The N gear is generally used for short-term parking, such as waiting at a red light, and the transmission should also be in the N gear when the car is being towed. 4. D Gear is the Driving Gear: When the gear lever is in the D position, the gears inside the transmission automatically switch between the lowest and highest gears according to the set shifting rules, based on factors such as vehicle speed and throttle opening. In most cases, you can drive using the D gear.
7
0
Share

Are Automatic Transmissions Prone to Failure?

Automatic transmissions do not easily fail during daily use. Here are some relevant details: 1. The internal structure of an automatic transmission is relatively more complex compared to a manual transmission, which means it requires more attention to maintenance during daily use. The primary aspects of maintaining an automatic transmission include ensuring the quality of the lubricating oil and avoiding operation under overload conditions to prevent overheating and aging of internal components. Due to its complex structure, transmission fluid plays an even more critical role. 2. In daily vehicle use, most automatic transmission failures stem from issues with the transmission fluid. Besides lubrication and cooling, automatic transmission fluid also assists in power transfer. If the fluid is not replaced for extended periods, impurities and sludge can accumulate, reducing its lubrication effectiveness and increasing wear on components like gears.
5
4
Share

What to Do When Mercedes-Benz Seat Adjustment Fails?

Reasons for Mercedes-Benz seat adjustment failure: 1. Electric seat jamming or seizing up. The seat adjustment linkage needs lubrication. 2. Wiring issues. Check the fuse first, then inspect if the seat motor is functioning properly. 3. Adjustment linkage or slide rails are blocked or lack lubrication. Automotive seats should meet the following requirements: 1. The arrangement of seats within the entire cabin should be reasonable, especially the driver's seat must be in the optimal position. 2. The seat's design must comply with human physiological functions, ensuring comfort while striving for aesthetics. 3. Seats must be safe and reliable, with sufficient strength, stiffness, and durability, featuring a compact structure and minimizing weight as much as possible. 4. Various adjustment mechanisms designed for passenger comfort must have reliable locking devices to ensure safety.
17
0
Share

Can a sedan be equipped with a roof rack?

Sedans can be equipped with roof racks. The installation method for roof racks is as follows: 1. Choose a suitable roof rack; 2. Thoroughly clean the roof surface. If there are no pre-installed screws on the roof, adhesive-type roof racks can be installed; 3. Find symmetrical and suitable positions, ensuring balance both front-to-back and side-to-side; 4. Slowly peel off the adhesive backing of the roof rack, stick it to the roof, and press firmly for more than 10 minutes to allow the adhesive to bond properly. Precautions for using roof racks include: 1. Ensure cargo is tightly secured or properly fixed on the rack and evenly distributed; 2. Use non-elastic ropes to tie down the luggage; 3. Pay special attention when carrying large items on the roof rack.
20
1
Share

Why Are Car Bumpers Made of Plastic?

The reasons why car bumpers are made of plastic are: 1. Consideration for pedestrian safety; 2. Practical usage considerations; 3. Facilitation of vehicle design and production. The car bumper is a safety device designed to absorb and mitigate external impacts, protecting the vehicle body and passenger safety. Plastic bumpers are manufactured using polyester and polypropylene materials through injection molding. They consist of an outer panel, cushioning material, and a crossbeam. The outer panel and cushioning material are made of plastic, while the crossbeam is formed by stamping cold-rolled thin steel sheets (approximately 1.5mm thick) into a U-shaped channel. The outer panel and cushioning material are attached to the crossbeam, which is then bolted to the vehicle frame's longitudinal beams, allowing for easy removal when necessary.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.