Why Does the Engine Lose Partial Power?

1 Answers
StephenFitz
07/30/25 12:35am
Engine partial power loss occurs due to carbon deposit issues and partial fuel line blockages. Carbon Deposit Issues: Carbon deposit issues include cylinder carbon deposits, throttle carbon deposits, spark plug carbon deposits, intake carbon deposits, etc. When excessive carbon deposits accumulate inside the engine, the vehicle's ignition energy decreases, intake efficiency drops, ultimately leading to reduced engine power and symptoms of weak idling. Partial Fuel Line Blockages: Blockages in the fuel tank vent hole, fuel tank switch, fuel filter, or the fuel lines between the tank and carburetor can restrict the required fuel supply, resulting in an overly lean air-fuel mixture and sluggish engine acceleration. Air intake is one of the engine's power sources; a clogged air filter from prolonged use without cleaning restricts airflow, causing an overly rich combustible mixture that reduces engine power. Insufficient engine oil, inadequate engine coolant, or malfunctioning engine cooling systems can increase engine load. Engine overheating leads to poor lubrication, increased mechanical wear, and diminished engine power.
Was this review help?
10
4
Share
More Forum Discussions

Where is the car door unlock button located?

The car door unlock button is typically located on the driver's side door or the central control area of the vehicle. The central locking system is a control device that simultaneously manages the opening and closing of all car doors, enhancing safety during driving. Vehicle central locking systems first appeared in the 1970s and were initially installed in sedans. After decades of development, this feature has become widely adopted. Automotive central locking systems can be divided into two main categories, as described below: 1. Door Lock Switch: This type of central locking switch consists of two components - a master switch and subsidiary switches. The master switch is located on the driver's side door, while subsidiary switches are installed on each individual door. 2. Door Lock Actuator: This central locking component executes the driver's commands to lock or unlock doors, and can be classified into three types: a. Electromagnetic Type: This actuator features two coils responsible for door locking and unlocking respectively, normally remaining in a neutral position. b. DC Motor Type: More complex in design, this actuator employs a DC motor and transmission mechanism to achieve door locking/unlocking through mechanical force. c. Permanent Magnet Motor Type: Utilizing a permanent magnet stepper motor, this type differs significantly in structure from the previous two, though its function and operating principle remain fundamentally similar.
15
1
Share

What are the symptoms of gear misalignment in a manual transmission?

Gear misalignment in a manual transmission manifests when, under normal clutch conditions, the gear lever cannot engage the desired gear, or cannot return to neutral after engagement, or simultaneously engages two gears, which is referred to as transmission misalignment. The following are the causes of manual transmission misalignment: 1. Wear or detachment of the curved working surface at the lower end of the gear lever, or excessive wear of the gear lever ball head; 2. Loose or worn positioning pin of the gear lever head, or detachment of the positioning pin, or excessive wear of the gear lever ball head; 3. Excessive wear (exceeding 0.02mm) of the lock pin or lock ball in the interlock mechanism of the shift fork shaft, resulting in loss of interlock function. 4. In summary, the main cause of misalignment is the failure of the transmission control mechanism, leading to engagement of an unintended gear instead of the desired one. The following are the troubleshooting methods for misalignment: 1. First, shake the gear lever to check its swing angle. If it exceeds the normal range, the fault is caused by looseness between the gear lever's lower end ball head positioning pin and the positioning groove, or excessive wear of the ball head or ball hole. 2. If the gear lever swings 360°, the positioning pin is broken. If the swing angle is normal but the gear still cannot be engaged or disengaged, the fault is caused by the detachment of the gear lever's lower end from the groove (due to wear of the curved working surface or guide groove). If two gears are engaged simultaneously, the fault is caused by failure of the interlock device.
15
1
Share

What does ESP in a car mean?

ESP is a general term for systems or programs designed to enhance vehicle handling performance while effectively preventing loss of control when the car reaches its dynamic limits. The functions of ESP are as follows: 1. Under certain road conditions and vehicle load conditions, the maximum adhesion force that the wheels can provide is a fixed value, meaning that in extreme situations, the longitudinal force and lateral force on the wheels have an inverse relationship. The electronic stability program can independently control the longitudinal braking force of each wheel, thereby influencing the lateral force and improving the vehicle's handling performance. 2. When the longitudinal force reaches its extreme value, the lateral force becomes zero, at which point the vehicle's lateral movement becomes uncontrolled, leading to skidding. In such cases, the vehicle may not be able to change lanes or turn as the driver intends. The electronic stability program can detect and prevent vehicle skidding. When it detects that the vehicle is about to lose control, it applies braking force to specific wheels to help the vehicle move in the direction desired by the driver. 3. During turns, one feasible control strategy is: when the vehicle shows a tendency to understeer, the system can apply braking force to the inner rear wheel of the turn. Since the longitudinal force on this wheel increases, the available lateral force decreases, generating a torque that assists in turning the vehicle. When there is a tendency to oversteer, the system can apply braking force to the outer front wheel of the turn. As the longitudinal force on this wheel increases, the available lateral force decreases, generating a torque that resists turning the vehicle. This ensures driving stability.
15
3
Share

Do You Need to Press the Brake for Automatic Transmission Gear Shifting?

Automatic transmission cars require pressing the brake when shifting gears; failing to do so can damage the automatic transmission. When driving, shifting from D to D3 or D2 does not require pressing the brake. However, if you suddenly shift from D to a lower gear at high speed, the engine RPM will become very high, and the car body will experience significant jerking. When driving at low speeds, you can directly shift to a lower gear. Some cars also have S or M modes, which can be switched to from D mode while driving. Additional Information: 1. D Mode Gear Shifting: When preparing to start driving, after pressing the brake, push the gear lever forward to D mode, then fully release the handbrake, gently press the accelerator, and after the car moves forward a certain distance, release the brake and continue pressing the accelerator. At this point, the car will automatically shift between gears 1 to 4 based on speed. Under normal driving conditions on flat roads, the driver does not need to shift to other gears. 2. When going downhill for a long distance, since the D mode of an automatic transmission car does not have engine braking functionality, do not keep it in D mode. Otherwise, the speed will keep increasing, posing safety risks, and frequent braking will cause the brake pads to overheat and wear excessively. P Mode Parking Gear Shifting: When the vehicle needs to be parked for a long time, especially on a slope, shift to P mode. In this mode, the wheels are mechanically locked, ensuring the vehicle cannot move while stationary. 3. It is important to note that you should shift to P mode after turning off the engine and then remove the key. Shifting to P mode before turning off the engine can damage the transmission gears. Never shift to P mode while the vehicle is moving, as this can cause severe damage to the vehicle.
4
3
Share

How to Quickly Improve Driving Skills?

Methods to quickly improve driving skills are as follows: 1. Before driving; (1) Walk around the car to check the tire conditions and ensure there are no obstacles around the vehicle that may affect driving; (2) Familiarize yourself with various controls in the driver's cabin, such as seat adjustment, how to fasten the seatbelt, and the use of the gear lever. Additionally, you should be very familiar with various dashboard instruments, steering wheel, clutch, brake, accelerator, ignition switch, etc., and be able to operate them correctly. The most important among these is the brake—it's crucial to develop the awareness of pressing the brake under any circumstances; (3) When not driving, mentally rehearse the entire driving process like watching a movie in your mind, and simulate driving actions with your hands and feet. Imagine where to place your hands and feet? How to start the car, how to shift gears, how to release the clutch with your left foot, how to press the accelerator, and how to shift gears and accelerate after the car starts. 2. Driving the car. (1) Find a friend to accompany you as a co-driver and practice on a road with no other vehicles, letting your friend randomly call out "stop" and "go." When your friend says "stop," you must stop the car; when your friend says "go," you must go. Repeat this practice until you can start and stop the car at will without stalling, which will enhance your control over the vehicle; (2) After becoming proficient in driving, develop the habit of observing the road conditions both in front of and behind the car. Remember not to focus only on the front because unexpected situations can come from behind. Therefore, adjust the rearview mirror to a suitable position to observe the rear at all times during driving.
8
1
Share

What is the best position to place the ETC in a car?

For small cars, the ETC is generally installed in the upper middle part of the front windshield, while for large vehicles such as trucks and buses, the installation position is in the lower middle part. The suitable installation position should be at a height of no less than 1.2 meters and no higher than 2.5 meters, with an installation angle between 30 and 90 degrees. For vehicles with anti-explosion film or those that have been retrofitted with anti-explosion film, it may affect the signal transmission of the microwave communication link, so it should be installed in the microwave sunroof strip. ETC stands for Electronic-Toll-Collection, which means electronic toll collection system. To apply for ETC, you need to provide the original and photocopy of the vehicle owner's valid ID card and driving license. If the application is not made by the vehicle owner, the agent's valid ID card is also required. The photocopy of the driving license should include the page with the latest annual inspection stamp. A bank card for deducting highway tolls is also required, and the vehicle must be registered under the name of an individual aged between 18 and 60. Here are some precautions for installing ETC: Do not block the view; it is best to install it behind the rearview mirror: Many car models have a large inclination angle of the windshield, which reduces the driver's field of vision. If this is not considered when installing the ETC, it will increase the driver's blind spot. Installing it behind the right side of the rearview mirror can avoid blocking the view. Do not affect charging: The ETC electronic tag consumes power, but generally does not need to be charged or have its battery replaced because it has a solar panel on the back that can charge itself. Therefore, when installing, avoid the black area on the windshield and do not place it where it can easily block the solar panel. Once installed, do not remove it at will: The button in the middle of the adhesive is an anti-removal lever, which is connected to a switch below. After the electronic tag is installed, the windshield will press the anti-removal lever in. If it is removed at will, the anti-removal lever will pop out and trigger the switch, locking the electronic tag and making it unusable. You will then need to go to an ETC service point to unlock it. This is designed to prevent multiple vehicles from sharing one device. When using ETC, note that: The ETC transaction sensing area is 8 meters. To prevent the ETC device of the vehicle in front from malfunctioning, keep a distance of more than 10 meters from the vehicle in front to avoid automatic sensing and paying for the vehicle in front. The ETC lane recognition speed is 20 kilometers per hour. If the speed is too fast, the vehicle equipment information cannot be read, leading to payment failure. When using a debit card to bind the ETC, insufficient balance will also cause payment failure.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.