Why does the electric vehicle battery get hot during charging? Is it normal?

How to Adjust the Height of Car Headlights?

There are two methods to adjust the height of car headlights. Here are the relevant introductions: 1. Most cars nowadays come with 'height-adjustable headlights,' and there is a height adjustment button inside the cabin. Turn it upwards to raise the lights, and downwards to lower them. Sitting in the driver's seat, you can observe noticeable changes by turning the button while watching the lights. The operation is very simple. This button can control both the front and rear headlights simultaneously. 2. Adjust the light button on the headlight assembly. A few models do not have the 'height adjustment' feature, and there is no height adjustment button on the headlights. Instead, there is a fine-tuning button on the headlights that can be used. Required adjustment tool: hex key. Most headlights are controlled by hex nuts, and an internal hex wrench is used to adjust these nuts. Adjusting the hex nuts ensures the headlights are at the same height.

15

5

Share

What are the steps for replacing the tie rod end on the Buick Encore?

For the Buick Encore, the steps to replace the tie rod end are as follows: 1. Preparation: Gather the necessary tools, including wrenches and sockets; 2. Remove the front left and right wheels: Turn the steering wheel to the center position, then remove the bolts; 3. Remove the tie rod end: Use tools to loosen the fixing nut of the tie rod end, unscrew the nut, fix the special tool on the ball pin and steering knuckle arm, and remove the ball joint; 4. Remove the tie rod bracket: Use a torque wrench and a 17mm socket with an extension to unscrew the two fixing nuts of the tie rod bracket, remove the nuts, and take out the tie rod bracket; 5. Remove the steering gear dust cover: Use pliers to loosen the clamping collar of the steering gear dust cover, then remove the fixing ring and dust cover; 6. Remove the tie rod and its ball joint: Use a hammer to loosen the clamping caps at both ends of the connecting rod, unscrew the left and right tie rod ends and connecting rod, remove the clamping caps, and unscrew the fixing nuts; 7. Inspect the tie rod end: Check the threads on the ball joint nut and replace if damaged; 8. Replacement: Finally, replace the ball joint.

15

2

Share

How to Check the Emission Standard of a Motor Vehicle?

Here are the methods to check the emission standard of a motor vehicle: 1. The simplest and most direct way is to look at the vehicle's environmental protection label, which has a clear mark on the back. 2. Log in to the website of the Motor Vehicle Exhaust Pollution Supervision and Management Center to inquire. 3. Bring the motor vehicle registration certificate (original or copy) to the vehicle management office for inquiry. 4. Differentiate based on the year the vehicle was registered. Vehicles registered after 2008 are National IV; those registered in 2007 are National III. Below is additional information on motor vehicle emission standards: 1. The main pollutants emitted by vehicles include HC (hydrocarbons), NOx (nitrogen oxides), CO (carbon monoxide), and PM (particulate matter). 2. Through the application of technologies such as improved catalytic converter active layers, secondary air injection, and exhaust gas recirculation systems with cooling devices, vehicle emissions can be controlled and reduced to below the specified standards.

5

3

Share

How to Replace the Fog Lights on a Nissan Tiida?

Replacing the fog lights on a Nissan Tiida involves the following three steps: 1. Use professional tools to gently pry the fog light cover from the inside outward, applying slight force to release the clips one by one. 2. Remove the screws around the fog light with professional tools. To avoid scratching the surrounding paint, you can wrap a thin cloth around the tool's head. 3. Before installing the new fog light, wear gloves. First, install the outer side, then the lower side should fit snugly against the daytime running light, and finally the inner upper side. Otherwise, the installation may not be properly aligned. After installing the new fog light, wipe off any fingerprints and dust with a clean cloth.

4

2

Share

How Long Does Automotive Liquid Glass Last?

It mainly depends on the frequency of use and the vehicle's operating environment. In areas with poor conditions, more windshield washer fluid will be used. Generally, a bottle of washer fluid has a volume of 2 liters, and there is no fixed refill cycle. Below is additional information about windshield washer fluid: 1. Never use tap water. The minerals in tap water can clog the windshield washer fluid lines. 2. When the air temperature drops below freezing, use windshield washer fluid with sufficient antifreeze components. Do not operate the windshield washer continuously for several seconds, and do not operate the washer when the fluid reservoir is empty, as this can cause the washer motor to overheat, leading to expensive repair costs.

12

1

Share

What Are the Causes of a Lean Air-Fuel Mixture in Cars?

Introduction to the causes of a lean air-fuel mixture in cars: In terms of the fuel system, a lean mixture essentially means insufficient fuel supply, resulting in a lower proportion of gasoline in the mixture. Insufficient fuel supply can be categorized into two types of faults: those outside the carburetor and those within the carburetor. Below are the detailed explanations: 1. Main causes of insufficient fuel supply outside the carburetor: (1) The fuel filter is clogged. (2) There is a blockage in the fuel line or the fuel pipe is damaged. (3) Loose or leaking fuel pipe connections. 2. Main causes of insufficient fuel supply within the carburetor: (1) The carburetor's fuel inlet is clogged, preventing smooth fuel flow from the external fuel system into the float chamber. (2) The float chamber fuel level is too low or the float is stuck. (3) The needle valve is stuck or other fuel outlets are clogged. (4) The main jet is clogged or improperly adjusted. Additionally, leaks in the intake manifold gasket or the carburetor base gasket can also cause the air-fuel mixture to become too lean.

17

3

Share

Why does the electric vehicle battery get hot during charging? Is it normal?

How to Adjust the Height of Car Headlights?

What are the steps for replacing the tie rod end on the Buick Encore?

How to Check the Emission Standard of a Motor Vehicle?

How to Replace the Fog Lights on a Nissan Tiida?

How Long Does Automotive Liquid Glass Last?

What Are the Causes of a Lean Air-Fuel Mixture in Cars?

What Are the Reasons for the Lack of Heat in the Air Conditioning System?

What does the exclamation mark in a triangle warning light mean?

What are the common faults of hydraulic steering systems?

Where is the air conditioning filter located in the Zotye SR7?