Why does the electric scooter's lights turn on but it doesn't move when twisting the throttle?

1 Answers
OJoanna
07/29/25 1:15am
Here are the reasons why the electric scooter's lights turn on but it doesn't move when twisting the throttle: Blown fuse: Replace the fuse. Faulty power switch: Replace the power switch. Damaged Hall throttle: Use a multimeter to measure the DC voltage output from the green wire at the throttle output terminal. If there is a 1-4.2V output, the throttle is normal. If there is no voltage output, the throttle is burnt out and needs replacement. Damaged controller: Use a multimeter to measure the DC voltage output from the red wire at the controller output terminal (connected to the throttle wire plug). If there is approximately 5V output, the controller is normal. If there is no voltage output, the controller is burnt out and needs replacement. Burnt power cut-off switch: If all the above possibilities are ruled out, unplug the power cut-off switch connector. If the motor runs normally, replace the power cut-off switch.
Was this review help?
19
3
Share
More Forum Discussions

How Many Hours Can a Private Car Run Continuously?

Private cars can run continuously for 12 hours. The following are situations that may occur during prolonged driving: 1. Engine overheating: Engine overheating is very dangerous and can damage engine performance. If on a regular road, promptly reduce speed, park the car in a relatively cool place like under a tree shade, let the engine idle, open the engine hood for ventilation and heat dissipation, and wait for the engine temperature to return to normal. If engine overheating occurs during high-speed driving or climbing, with the water temperature gauge needle entering the red zone, remaining high, or fluctuating repeatedly, immediate action must be taken. 2. Tire overheating: Low tire pressure, braking, or friction between the tire and the car body can cause tire overheating. If tire overheating occurs, to avoid a blowout, driving should not continue. Pouring cold water immediately can cause tire damage due to sudden thermal expansion and contraction. 3. Brake fade: Brake fade refers to the reduction in braking force caused by high temperatures from intense friction between the brake disc and brake pads. Excessively high temperatures can even lead to brake failure. Therefore, once brake fade occurs, shift to a lower gear to make full use of engine braking. If the situation is severe, it is best to stop and wait for the brake system to cool down naturally before continuing to drive, to avoid safety issues.
17
2
Share

How to change from C1 to C2 driver's license?

To change from a C1 to a C2 driver's license, you need to bring your ID card and driving school procedures to the municipal vehicle management office for a new physical examination, form replacement, and completion of the change procedures. A C1 driver's license allows driving all vehicle types under C2, C3, and C4. A C2 license does not permit driving work vehicles. The test items for C1 and C2 are the same. In terms of difficulty, since the automatic transmission C2 does not have a clutch, the operation is simpler than C1.
7
5
Share

What are the differences between National IV, National V, and National VI?

The differences between National IV, National V, and National VI are that the later standards impose stricter emission requirements. Additionally, the standards for nitrogen oxides (NOX), the combined total of hydrocarbons and nitrogen oxides (HCNOX), and particulate matter (PM) concentrations have been raised. Compared to National IV, National V requires a 25% reduction in nitrogen oxide emissions, while National VI demands a reduction of over 50% compared to National V. In terms of particulate matter, National VI reduces emissions by 42% compared to National V, making the National VI standard significantly more stringent than National V. Additional information: 1. Vehicle Emission Standards: Vehicle emission standards are national regulations designed to limit the production of harmful gases such as CO (carbon monoxide), HC+NOx (hydrocarbons and nitrogen oxides), and PM (particulate matter, soot) emitted from vehicle exhaust. 2. Standard Classification: China's motor vehicle pollutant emission standards are largely equivalent to the European Union's emission standards, hence the similar terminology is used domestically. However, there are still some technical differences between the two. China's "Limits and Measurement Methods for Emissions from Light-Duty Vehicles (I)" is equivalent to the "Euro I" standard, while "Limits and Measurement Methods for Emissions from Light-Duty Vehicles (II)" is equivalent to the "Euro II" standard.
8
3
Share

Where is the front USB port of the 2020 Tayron?

2020 Tayron's front USB port is located in the middle position below the control screen. Here are the specific details about the Tayron: 1. The Volkswagen Tayron has 33 storage spaces inside the car, with a high space utilization rate. 2. The front face design of the Volkswagen Tayron is very refined. Although it is a mid-size SUV, the LED headlights adopt an open-eye design, and the LED daytime running lights feature a ring-shaped design, giving it a very high recognition. 3. In terms of body dimensions, the Volkswagen Tayron is 4589 mm in length, 1860 mm in width, 1660 mm in height, and has a wheelbase of 2731 mm.
17
4
Share

What is the Honda Spirior?

Spirior is a high-performance sports sedan from Honda. Here are the specific details about the Honda Spirior: 1. The Spirior emphasizes handling and power performance, equipped with a 2.0L engine paired with a CVT transmission and a 2.4L engine paired with an 8-speed dual-clutch transmission. 2. There is also a 2.0L hybrid version of the Spirior. 3. The Spirior is one of the few Honda models that focuses on interior configuration, but it still falls short compared to the Civic and Accord.
13
2
Share

What is the speed requirement for shifting gears in Subject 3?

Subject 3 gear and speed standards: 1st gear: 0-20 mph; 2nd gear: 5-30 mph; 3rd gear: 15-40 mph; 4th gear: 30-55 mph. The highest gear required in Subject 3 is the fourth gear, which is shifted during straight-line driving. Normal driving is in third gear, but starting and pulling over require first gear. Pay attention to the correct use of gears. The relevant information for Subject 3 is as follows: 1. Definition: Subject 3, also known as the road test, is part of the motor vehicle driver's license assessment. It is the abbreviation for the road driving skills and safe civilized driving knowledge test in the motor vehicle driver's examination. 2. Subject 3 road test: Preparation before driving (including fastening the seat belt, observation, and turning on the left turn signal), starting, straight-line driving, changing lanes, passing through intersections, pulling over, passing through pedestrian crossings, passing through school zones, passing through bus stops, meeting vehicles, overtaking, making U-turns, and driving at night. Additional test items include gear shifting operations, left turns at intersections, and right turns at intersections. The ability to observe, judge road and driving conditions, and comprehensively control the motor vehicle, knowledge of using various lights at night and in low visibility conditions, awareness of traffic regulations, and safe driving conditions are also assessed.
6
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.