Why does the Corolla's fan keep running when the air conditioning is on?

What is the fuel tank capacity of the Malibu XL in liters?

Currently, there are 9 models of the Malibu XL available for sale. The 535T version has a fuel tank capacity of 55 liters, while other versions have a capacity of 60 liters. This data is provided by the automobile manufacturer, and owners who have purchased the Malibu XL can also check it on the vehicle's configuration sheet. The 535T version of the Malibu XL uses 92-octane fuel, while other series use 95-octane fuel. The fuel consumption per 100 kilometers ranges from 6.3 to 6.7 liters, and a full tank can cover a distance of 873 to 896 kilometers. During daily driving, it is necessary to always pay attention to the remaining fuel in the tank. Generally, this is observed through the fuel gauge inside the vehicle. If there are no other issues, the fuel level will be accurately reflected on the gauge. The fuel gauge typically has 5 to 6 segments, and it is advisable to refuel when there are only 2 segments left to avoid running out of fuel midway. During the actual refueling process, the amount of fuel may exceed the marked capacity. This is because the fuel tank capacity marked by the automobile manufacturer is measured from the bottom of the tank to the safety limit, and there is still some space from the safety limit to the tank opening. This space is reserved to allow for fuel expansion when the temperature rises, preventing overflow from the tank's safety space. If fuel is added up to the tank opening during refueling, the actual amount of fuel added may exceed the marked tank capacity.

3

0

Share

How to Replace the Rear Brake Pads on an Audi A4L?

Audi A4L brake pad removal and replacement process is as follows: 1. Check the brake fluid level. Before replacing the brake pads, open the cap of the brake fluid reservoir in the engine compartment and check the brake fluid level. If the brake fluid level is above the maximum limit, some should be siphoned out to prevent overflow during the replacement process. 2. Remove the wheel. Prepare the new brake pads for replacement and remove the wheel where the brake is located. Be careful to avoid scratching the rim during removal. 3. Remove the brake pads. Use a wrench with a socket to remove the bolts of the brake caliper, then take out the brake pads (if there is a brake sensor wire, remove it first). Check if the brake pads are excessively worn or cracked, and proceed with the next step if they are. 4. Apply anti-squeal paste. Since the brake caliper may have a lot of sand or dirt, clean it thoroughly with a cloth and then apply anti-squeal paste to prevent noise during braking. 5. Install the new brake pads on the caliper. Use a piston press to push the piston to its limit, then install the new brake pads on the caliper. After the new brake pads are properly installed (including the brake sensor wire if applicable), tighten the guide bolts to complete the installation. 6. Cover the reservoir and reset the brake. After installation, cover the reservoir cap, get into the car, and press the brake pedal firmly several times to reset the brake. Then check the brake fluid level to ensure it is within the appropriate range. 7. Test drive. After replacement, take a test drive to check if the braking effect is satisfactory. The replacement interval for brake pads and discs is not fixed and depends on the vehicle's driving conditions, the frequency of brake pedal usage, and the force applied by the driver.

4

0

Share

What does it mean when the ECO light on the car dashboard is on?

When the eco indicator light on the car is on, it indicates that the vehicle's economy mode has been activated. ECO is an English abbreviation, derived from the combination of Ecology (environmental protection), Conservation (energy saving), and Optimization (power). The Eco mode is further divided into active eco driving mode and non-active eco driving mode. Eco mode is categorized into active and non-active types, with the difference being that the active type has its own dedicated button, allowing the driver to choose whether to activate it. When the driver presses the eco mode switch, the dashboard indicator light will immediately illuminate, and the vehicle will automatically begin adjusting settings such as throttle opening, transmission shift logic, and air conditioning output power. The non-active eco mode does not have a dedicated button. When the dashboard eco indicator light is on, it serves merely as a reminder function. The eco system automatically evaluates driving behavior, and if the current driving operation achieves the optimal fuel supply, the dashboard will simultaneously display the eco indicator light. Most cars use the active eco driving mode, meaning they have their own switch button. Therefore, during daily driving, the eco mode can be activated. However, it is unnecessary to turn on the eco mode when driving at speeds exceeding 120 km/h, during idle parking, in N/P gear, or in manual mode, especially when climbing hills, as it does not reflect the fuel-saving characteristics of the eco mode. In addition, the eco mode typically becomes ineffective under the following conditions: When the vehicle speed exceeds 120 kilometers per hour, the car will prioritize speed, and the eco mode will automatically deactivate. During idle parking or when in N/P gear or manual mode, the eco mode may also become ineffective. When high torque output is required, such as when climbing a hill, the engine computer will prioritize ensuring sufficient power to drive the vehicle, and the eco mode will not function.

19

3

Share

What is the warranty period for the Sylphy?

5 years or 150,000 kilometers. According to Article 17 of the "Regulations on the Repair, Replacement, and Return of Household Automotive Products," the warranty period for household automotive products shall not be less than 3 years or 60,000 kilometers, whichever comes first. The three-guarantee validity period for household automotive products shall not be less than 2 years or 50,000 kilometers, whichever comes first. The warranty period and three-guarantee validity period for household automotive products shall be calculated from the date the seller issues the vehicle purchase invoice. Below is more related information: Article 12 of the "Regulations on the Repair, Replacement, and Return of Household Automotive Products" states that when selling household automotive products, the seller shall meet the following requirements: 1. Deliver qualified household automotive products and invoices to consumers. 2. Deliver accompanying tools, spare parts, and other items to consumers according to the vehicle item list and other accompanying documents. 3. Inspect the appearance, interior, and other quality conditions of the household automotive product on-site in the presence of the consumer. 4. Clearly indicate and deliver the product manual, three-guarantee certificate, maintenance manual, and other accompanying documents. 5. Clearly indicate the three-guarantee terms, warranty period, and three-guarantee validity period for the household automotive product. 6. Clearly indicate the repair network information, including the name, address, and contact number of the repairer agreed upon by the manufacturer, but shall not restrict consumers from freely choosing a repairer from the aforementioned repair network. 7. Fill in relevant sales information on the three-guarantee certificate. 8. Remind consumers to read safety precautions and follow the instructions in the product manual for use and maintenance.

5

0

Share

ETC Installation Location?

For small cars, the ETC device is generally installed on the upper middle part of the front windshield, while for large vehicles such as trucks and buses, it is installed on the lower middle part. The appropriate installation position should be no lower than 1.2 meters and no higher than 2.5 meters, with an installation angle between 30 to 90 degrees. For vehicles with anti-explosion film or those that have it installed later, which may affect the signal transmission of the microwave communication link, the device should be installed in the microwave skylight zone. ETC stands for Electronic Toll Collection, an electronic toll system. To apply for ETC, the vehicle owner needs to provide valid identification and the original and photocopy of the vehicle registration certificate. If the application is made by someone other than the owner, the agent's valid identification is also required. The photocopy of the vehicle registration certificate should include the page with the most recent annual inspection seal. A bank card for deducting highway tolls is also needed, and the vehicle must be registered under the name of an individual aged between 18 and 60. Documents required for official vehicles: An introduction letter from the vehicle owner (with official seal); a photocopy of the organization code certificate or business license (with official seal); the original ID of the agent; the original vehicle registration certificate; and the vehicle for which ETC is to be applied. Here are some precautions for ETC installation: Do not obstruct the view; it is best to install it behind the rearview mirror: Many car models have a large inclination angle of the windshield, which reduces the driver's field of vision. If this is not considered during ETC installation, it may increase the driver's blind spots. Installing it behind the rearview mirror on the right side can avoid obstructing the view. Do not interfere with charging: The ETC electronic tag consumes power but generally does not require charging or battery replacement, as it has a solar panel on the back for self-charging. Therefore, during installation, avoid the black areas on the windshield and positions that may block the solar panel. Once installed, do not remove it casually: The button in the middle of the adhesive is an anti-removal lever connected to a switch. After installation, the windshield will press the anti-removal lever in. If the device is removed casually, the lever will pop out and trigger the switch, locking the electronic tag and rendering it unusable. In such cases, you will need to visit an ETC service point to unlock it. This is designed to prevent multiple vehicles from sharing one device. Precautions for using ETC: The ETC transaction sensing range is 8 meters. To prevent the ETC device of the vehicle in front from malfunctioning, maintain a distance of more than 10 meters from the vehicle in front to avoid automatic toll deduction for the preceding vehicle. The ETC lane recognizes vehicles at a speed of 20 km/h; driving too fast may result in failure to read the vehicle's device information and unsuccessful toll deduction. When using a debit card linked to ETC, insufficient balance may also cause toll deduction failure.

15

0

Share

What are the symptoms of a faulty transmission valve body in an Audi A6?

The symptoms of a faulty transmission valve body in an Audi A6 are that the spool valves on the valve body move left and right to change the flow direction and pressure of the hydraulic oil, enabling the automatic gear shifting by engaging the clutches and brakes of different gears. Sticking or leakage of the valves can lead to gear shift shocks, low transmission efficiency, and poor power performance. Relevant information about the Audi A6 is as follows: 1. Performance Configuration: The new Audi A6L adopts a five-link front suspension design, balancing the necessary rigid connection for sportiness and comfort with low static stiffness. Among them, the hydraulic frame damping support significantly improves driving comfort and effectively reduces the impact and jolt when passing over speed bumps or uneven road surfaces, thereby reducing the impact on the lumbar spine. The hydraulic damping support is also applied to the optimized rear subframe, greatly improving vibration comfort and reducing longitudinal moments generated by tire-road contact and uneven moments caused by the rear axle's rotation. This technology was previously applied in the Audi Q5 and received unanimous praise from the media and customers. In addition to the damping supports used in the suspension system, the powertrain of the new Audi A6L also employs numerous hydraulic damping supports, significantly enhancing engine vibration and noise comfort. 2. Interior Atmosphere: The new Audi A6L has undergone extensive work in interior design and material selection. According to surveys, Audi A6 drivers spend more time in their cars than average, so Audi A6 users require a relaxed and comfortable driving atmosphere during long drives. The standard interior of the new Audi A6L already fully meets this demand. On this basis, further options such as Silhouette fabric, Milano leather, and Valcona leather, complemented by decorations made of glazed black plastic, aluminum alloy, ash wood, and brown walnut wood, provide even more upscale interior choices.

5

Share

Why does the Corolla's fan keep running when the air conditioning is on?

What is the fuel tank capacity of the Malibu XL in liters?

How to Replace the Rear Brake Pads on an Audi A4L?

What does it mean when the ECO light on the car dashboard is on?

What is the warranty period for the Sylphy?

ETC Installation Location?

What are the symptoms of a faulty transmission valve body in an Audi A6?

Why is it difficult to start the Haval H6 manual transmission on an uphill slope?

What are the pros and cons of flashing ECU to increase idle speed in the 8th generation Accord?

Will the car engine get water in on rainy days?

What is a Hands-Free Liftgate?