Why does the Changan Eado Plus display abnormal tire pressure?

1 Answers
SophieRose
07/29/25 12:32pm
Changan Eado Plus displays abnormal tire pressure. The first reason: The tire pressure monitoring system has not been fully reset. After inflating the tires of the Eado PLUS, the warning does not disappear immediately. The tire pressure system has a self-learning phase. Solution: Inflate all four tires to 2.5Bar and drive the vehicle for about 2KM. The tire pressure system will automatically relearn, and the tire pressure will reset itself. The second reason: Tire pressure sensor issue The Eado PLUS has independent tire pressure sensors in all four tires. These sensors are located inside the tires. During tire repair, the tires need to be removed. If the repair technician is not careful with the tire pressure sensors, the tire mounting machine may damage them, causing sensor failure and inability to monitor tire pressure. Solution: Replace the tire pressure sensor.
Was this review help?
9
3
Share
More Forum Discussions

What to Do When the Steering Wheel of a Mercedes-Benz Car Locks?

When the key is pulled out, as long as the steering wheel is turned, the steel pin will pop into the pre-drilled hole and then lock the steering wheel to ensure it cannot be turned. Steering wheel lock-ups often occur with novice car owners because after parking and turning off the engine, they notice the steering wheel is not straightened and then habitually try to turn it back by hand.
5
0
Share

How to Play Music from a USB Drive in a Buick Excelle?

First, locate a conveniently accessible USB port inside the Buick Excelle vehicle and insert the USB drive into the USB port. Start the Buick Excelle vehicle, then press the operation button on the Buick Excelle's center console to switch to AUX mode. After waiting a few seconds, when the icon appears on the Buick Excelle's display screen, the songs from the USB drive will start playing in the vehicle, completing the operation.
4
5
Share

What is the correct method for pressing and releasing the clutch?

When you press the clutch to shift gears and the car's speed hasn't yet increased, the clutch should be released slowly. Releasing the clutch too quickly can cause the engine to stall. The correct operation is to slowly release the clutch until the engine starts to vibrate, then release the brake pedal and immediately press the accelerator to follow up. If the clutch pedal is not fully pressed down when shifting gears, it can cause a "gear grinding" phenomenon. Doing this frequently can cause significant damage to the transmission.
18
1
Share

How to Remove the Inner Door Panel of a 2012 Sail?

Prepare one large flat-head screwdriver, one small flat-head screwdriver, one Phillips-head screwdriver, and one T-20 Torx key. Now, let's begin. Open the car door. You will find a round decorative cover near the interior handle. Use the small flat-head screwdriver to gently pry off this small circular cover. Carefully remove the small decorative cover with the small flat-head screwdriver, then use the Phillips-head screwdriver to remove the screw located below it.
19
4
Share

How to Open a Lynk & Co Car Key?

Press the small silver button on the key with one hand while pulling out the metal key with the other hand. Insert the larger end of the metal key into the notch of the electronic key. Gradually apply force to twist the metal key, then gently remove the key circuit board and pry open the back cover of the electronic key. Carefully remove the circuit board of the electronic key (sweat or water may corrode the circuit). Remember the orientation of the electronic components, use the metal key to pry out the electronics. Install a new battery.
11
3
Share

What is the method for removing the gear knob of the Buick Excelle?

First, it's essential to understand what a gear knob is and locate it. Begin by removing the leather cover on the gear knob of the Sorento. Then, take out the prepared pry bar and use it to carefully and slowly pry around the edges of the gear knob's leather cover. Next, lift the entire leather dust cover on the gear knob upwards gently. Finally, pry open the clips around the gear knob's leather cover. Once all clips are released, the gear knob can be removed, thus completing the process.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.