Why does the car shake violently while driving?

Where is the Car Child Lock Located?

Car child lock is located slightly below the rear door latch. Here is an introduction to car child locks: 1. Introduction: Car child lock, also known as door lock child safety. 2. Location: It is set on the rear door lock of the car. Open the rear door and there is a small lever (safety mechanism) below the door lock. Push the lever towards the end with the child icon, then close the door. At this time, the door cannot be opened from inside the car, but can only be opened from outside. 3. Function: Its function is that when children are seated in the rear, it can prevent active and unaware children from opening the door during driving, thereby avoiding danger. In this case, the door can only be opened by adults from outside after the car is parked.

16

2

Share

What is the normal oil pressure in bar?

Oil pressure is generally considered normal when maintained within the range of 150 to 350 kPa. If the pressure gauge indicates a value below 98 kPa, it can be regarded as low oil pressure, and the vehicle should be stopped immediately for inspection. Otherwise, it may lead to excessive wear of components or even serious mechanical failures such as "bearing seizure." Below are the common causes of low oil pressure: Insufficient oil quantity: If the oil level is insufficient, the oil pump's output will decrease or fail to pump oil due to air intake, resulting in reduced oil pressure. This can cause accelerated wear of the crankshaft and bearings, as well as the cylinder liners and pistons due to inadequate lubrication. Engine overheating: Excessive scale in the cooling system, poor heat dissipation, prolonged overloading, or delayed fuel injection timing can cause the engine to overheat. This accelerates oil degradation, thinning, and leakage through various clearances, leading to pressure loss. Oil bypass valve malfunction: The oil bypass valve maintains normal oil pressure in the main oil gallery. If its pressure-regulating spring weakens, is improperly adjusted, or if the valve seat and ball wear out or get stuck, preventing proper sealing, oil pressure will drop. Oil filter clogging: When the oil filter is clogged and cannot allow flow, the bypass valve on its base opens, allowing oil to bypass filtration and enter the main oil gallery directly. If the bypass valve's opening pressure is set too high, it may not open promptly when the filter is clogged, causing increased oil pump pressure, internal leakage, and subsequent pressure drop.

15

5

Share

What are the reasons for the C4L air conditioner not cooling?

Detailed reasons and solutions for the Citroen C4L air conditioner not cooling are as follows: 1. Insufficient refrigerant in the car air conditioning system: The car air conditioning system consists of multiple metal pipes with small gaps between them, leading to slight refrigerant leakage. The drying bottle in the car air conditioning system absorbs moisture and stores some refrigerant, so when the refrigerant level decreases to a certain extent, the cooling capacity of the car air conditioner will be reduced. Solution: Refill the refrigerant. 2. Clogged filter screen: Excessive impurities in the refrigerant and refrigeration oil of the car air conditioner can also clog the filter screen, reducing cooling efficiency, increasing resistance, and decreasing the flow of refrigerant to the expansion valve, resulting in the car air conditioner not cooling. Solution: Clean the filter screen.

16

0

Share

Is Passing Subject 3 Required Before Taking Subject 4?

Passing Subject 3 is mandatory before taking Subject 4, as Subject 4 is part of Subject 3. Subject 3 consists of two parts: the road test and the theoretical exam. Below are the relevant details: 1. Regulations: The vehicle management office must arrange exams according to the scheduled test center and time. After passing Subject 1, applicants can schedule Subject 2 or the road driving skills test for Subject 3. In some regions, applicants may simultaneously schedule Subject 2 and the road driving skills test for Subject 3, and upon successful scheduling, they can take these exams consecutively. After passing both Subject 2 and the road driving skills test for Subject 3, applicants can participate in the Subject 3 safety and civilized driving knowledge test on the same day. 2. Subject 4 Content: Requirements for safe and civilized driving operations, knowledge of safe driving under adverse weather and complex road conditions, handling methods for emergencies such as tire blowouts, and knowledge of post-accident procedures.

10

3

Share

What are the benefits of changing engine oil?

The benefits of changing engine oil are as follows: 1. Lubrication and friction reduction: There is rapid relative sliding between pistons and cylinders, as well as between main shafts and bearing bushes. To prevent excessive wear of components, an oil film needs to be established between the two sliding surfaces. A sufficiently thick oil film separates the relatively sliding component surfaces, thereby achieving the purpose of reducing wear. 2. Cooling: Engine oil can carry heat back to the oil tank and then dissipate it into the air, helping the radiator cool the engine. 3. Cleaning: Good engine oil can circulate carbon deposits, sludge, and worn metal particles from engine components back to the oil tank. Through the flow of lubricating oil, it washes away dirt generated on the working surfaces of components. 4. Sealing and leak prevention: Engine oil can form a sealing ring between piston rings and pistons, reducing gas leakage and preventing external contaminants from entering. 5. Rust and corrosion prevention: Lubricating oil can adhere to component surfaces, preventing contact with water, air, acidic substances, and harmful gases. 6. Shock absorption: When the pressure at the engine cylinder port rises sharply, suddenly increasing the load on pistons, piston rings, connecting rods, and crankshaft bearings, this load is transmitted and lubricated through the bearings, cushioning the impact load.

10

4

Share

What Causes the Squeaking Sound in Mercedes-Benz Brakes?

Mercedes-Benz brake noise is caused by issues in the braking system. If the car is new, both the brake pads and brake discs are brand new, and they are in the break-in period, which may result in noise during driving. Owners need not worry as this noise will automatically disappear after the break-in period. Below are the detailed reasons for brake noise: 1. Brake pad material issues: Most brake pads currently used are semi-metallic and semi-asbestos. If the metal in the brake pads is too hard, it can cause noise during braking. 2. Uneven brake discs: Brake discs may develop uneven surfaces during use. When the brake discs become uneven, stepping on the brakes can more easily produce noise. 3. Worn edges of brake discs forming protrusions: When new brake pads are installed, if they do not fully align with the brake discs, noise may also occur during braking.

9

5

Share

Why does the car shake violently while driving?

Where is the Car Child Lock Located?

What is the normal oil pressure in bar?

What are the reasons for the C4L air conditioner not cooling?

Is Passing Subject 3 Required Before Taking Subject 4?

What are the benefits of changing engine oil?

What Causes the Squeaking Sound in Mercedes-Benz Brakes?

What is the round button on the seat belt called?

What does Lavida insp mean?

What are the types of Mercedes-Benz?

Why is the screen of the Audi Q5 not lighting up, and the buttons are also not working?