Why does the car air conditioner have cold air but not cool enough?

2 Answers
ClaireDella
07/28/25 10:15pm
Here are the reasons why the car air conditioner has cold air but is not cool enough: 1. Lack of refrigerant: Sometimes there is an issue with the refrigerant in the car air conditioning system. 2. Loose air conditioning compressor belt: When the belt driving the car air conditioning compressor is loose, the compressor will slip during operation. 3. Dirty condenser: It is often found in summer that the air conditioning does not work well. 4. Clogged air filter: If the filter is too dirty, it will affect the airflow. Here is additional information on why the air conditioner is not cooling: 1. Internal damage: Severe internal wear of the compressor can prevent it from working properly. 2. Oil stains: Oil stains at connection points or seams indicate refrigerant leakage, and the relevant parts should be tightened or replaced. 3. Circuit system failure: Circuit system failures are also a very common reason why the car air conditioning compressor cannot work normally. You can check if the circuit is unobstructed, inspect the temperature sensor solenoid valve, and other potential fault causes. 4. Low-pressure gauge reading much lower than normal: The surface temperature of the compressor suction pipe is lower than normal, appearing damp and cold (commonly known as sweating).
Was this review help?
6
0
Share
MacLaila
08/12/25 2:46am
I found that the car's air conditioning has cold air but it's not cooling properly, which is mostly caused by insufficient refrigerant or a leak. Refrigerant is like the blood of the air conditioning system; without enough of it, the cooling effect won't be achieved. Compressor aging is also a common issue—if it's not running smoothly, cold air won't come out. I often see the condenser clogged with dust or leaves, leading to poor heat dissipation and an immediate drop in air conditioning efficiency. Additionally, a dirty air filter can block airflow, reducing the cooling effect when the cold air is blown out. If none of these components are the issue, it might be an internal system leak or a malfunctioning thermostat. It's best to visit a repair shop for a thorough inspection without delay, as it affects driving comfort. Regular maintenance before seasonal changes can prevent this problem from occurring.
Was this review help?
8
4
Share
Expand All
More Forum Discussions

What does maxac mean in a car?

In car air conditioning, maxac refers to activating the maximum cooling mode. Here are some relevant details about car air conditioning: 1. A/C stands for air condition, which can be understood as air control or air regulation. Its function in a car is essentially the air conditioning cooling switch. When the A/C light is on, it indicates that the air conditioning compressor is engaged, increasing engine load and fuel consumption. 2. The compressor only operates when this button is pressed, causing the blower to produce cold air. When you press the AC button, the electromagnetic clutch of the air conditioning compressor engages, making the compressor rotate with the engine and enter the cooling state.
13
3
Share

Does the 10th-generation Civic have a tire pressure monitoring system?

10th-generation Civic is equipped with a tire pressure monitoring system. Here are some points regarding tire pressure checks: 1. In hot weather, a drop in temperature may lead to underinflation. 2. In cold weather, a rise in temperature may lead to overinflation. When overinflated, the low tire pressure indicator will not illuminate. 3. Mixing tire types and sizes may cause the tire pressure monitoring system to malfunction. 4. When driving on snowy or slippery roads, use snow chains. 5. When using a compact spare tire. 6. During rapid acceleration, sudden braking, or quick steering wheel turns.
17
3
Share

What to Do When the Geely Emgrand Can't Shift Gears?

Check and adjust the free travel of the clutch pedal. For hydraulic control mechanisms, inspect the working travel of the master cylinder, slave cylinder, and push rod, and bleed the system. Check whether the release levers are on the same plane and if the support bolts are loose. If the issue persists after inspection, disassemble the clutch to examine each assembly and replace if necessary. Inspect the alignment between the transmission's first shaft and the clutch driven disc. Adjust promptly if misaligned. Fully depress the clutch pedal before shifting gears. Incomplete pedal depression can cause gear grinding and, over time, significant damage to the transmission.
19
3
Share

How to Clean Dirty Car Interior?

Cleaning methods for dirty car interior: 1. Center console cleaning: Use cleaning putty to clean the gaps; 2. Door panel cleaning: Use a cleaning agent to dissolve dirt on the door panels, then wipe with a towel to remove the stains; 3. Roof liner cleaning: Spray cleaning agent, scrub with a brush, and finally wipe off the moisture with a towel. Car interior mainly refers to the products used for modifying the inside of a car, covering various aspects such as steering wheel covers, seat cushions, floor mats, car perfumes, hanging accessories, interior decorations, and storage boxes.
5
4
Share

What does the CBIP0005 error mean?

CBIP0005 error indicates an open circuit in the fuel shutoff valve control circuit. Generally, the fault code needs to be cleared: When clearing the fault code, it is essential to strictly follow the specified method for the particular vehicle model. Never simply remove the negative battery cable to clear the fault code. Function of the fuel shutoff valve: It cuts off the fuel supply to the engine in emergency situations (such as a rollover). This fault code indicates that the Electronic Control Unit (ECU) has detected that the voltage in the fuel shutoff valve A control circuit exceeds the calibrated maximum range.
20
2
Share

How to Remove the Logo from Car Film?

Methods to remove the logo from car film are as follows: 1. Alcohol Wiping: Use a towel, tissue (or cotton swab) dipped in alcohol to gently wipe the logo. After wiping, it's best to clean the area with water. Note that directly spraying alcohol on the logo watermark is not recommended. 2. Tar Remover (or Asphalt Remover): If alcohol doesn't work, you can try using a tar remover or asphalt remover, which are commonly available at auto repair shops. Spray the tar remover (or asphalt remover) on the logo watermark area of the film—use an appropriate amount, not too much. This reagent evaporates quickly, so wipe it off with a towel immediately after spraying, then rinse with clean water.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.