Why does the Buick Excelle fan keep running continuously?

How to Install Dual Throttle Cables?

Adjust the clearance and tightness of the throttle handle, then test acceleration. This indicates interference in the throttle cable, which causes a rustling sound when pulled, mostly due to the cable being coiled around the handle. During operation, a "clicking" sound may occur, in which case it is best to replace with a new cable. Hold the adjustment nut and pull the cable outward by 2-3mm, then check if the clearance is appropriate. Turn the adjustment nut clockwise to tighten the cable. When the clearance returns to its pre-failure state, the cable tension is considered appropriate.

6

1

Share

How to Install a Water Plug?

Clean the sealing ring position thoroughly. Replace with a new sealing rubber ring. Cut a 6 cm long nylon rod, shaped as shown, with a small end diameter of 20 mm and length of 4 cm, followed by a step with a diameter of 35 mm. Insert it into the hole where the sealing rubber ring is located. This hole has a diameter of 20 mm. After tightly fitting it into the drainage column hole, it can be pressed into its original position. The pressure from the spring at the top of the drainage column should be slightly higher.

2

1

Share

How to Drain the Water from the Radiator?

Drain the existing water from the radiator. There is a drain valve at the bottom of the radiator. For some vehicle models, it is also necessary to drain the water from the engine block, where there is a drain plug. There is a drain valve at the bottom of the radiator. After draining the water, tighten it and add antifreeze. Simply open the drain valve at the bottom of the radiator. "Antifreeze" is a chemical solution with a low freezing point, which can drop below -60 degrees Celsius. It will not freeze due to low temperatures and will not damage the engine.

4

2

Share

How to Repair a Flood-Damaged Car?

Remove the seats and the entire floor carpet. Generally, there is a thick layer of sponge beneath the carpet. Use a vacuum cleaner to suck out the water until no more can be extracted, then place the car in a paint baking room to dry. It is recommended to use the tube heating method and avoid using fuel-fired heating. Adjust the temperature to 55 degrees Celsius, as this temperature will not damage the interior or leather. After drying, do not rush to reassemble. Use a fan to blow for several hours to remove any odors. Assemble carefully and professionally, and there will be basically no harm to the car.

10

3

Share

Can You Drive on the Highway with a Spare Tire?

You can drive on the highway with a spare tire, but non-full-size spare tires should not exceed 80 km/h. Below are the classifications for using different types of spare tires: 1. Full-size spare tires have no restrictions on mileage or speed and can replace any temporarily or permanently unusable tire, as they are the same size as the original tires. 2. Non-full-size spare tires can only be used on non-drive wheels and must not exceed a speed of 80 km/h, as their diameter and width are slightly smaller than the other four tires, making them suitable only for temporary use. 3. Run-flat tires (commonly known as "puncture-proof tires") do not lose air or lose air very slowly when punctured, maintaining their shape and keeping the tire bead fixed to the rim, allowing the car to drive stably for a long or short distance to a repair station.

20

2

Share

What is the function of the Jetta intake sensor?

The function of the Jetta intake temperature sensor: It detects the intake air temperature and provides the data to the ECU as a basis for calculating air density. Below is an introduction to the intake sensor: 1. Modern cars can classify sensors based on their functions, such as measuring temperature, pressure, flow, position, gas concentration, and speed. 2. The intake temperature sensor is a negative temperature coefficient thermistor. When the temperature rises, the resistance decreases; when the temperature drops, the resistance increases. The change in resistance in the circuit leads to a change in voltage, thereby generating different voltage signals to complete the automatic operation of the control system. 3. When the engine is cold, the signal from the intake temperature sensor is basically the same as that from the engine coolant temperature sensor. When the engine is warm, its signal voltage is approximately 2~3 times that of the coolant temperature sensor.

2

0

Share

Why does the Buick Excelle fan keep running continuously?

How to Install Dual Throttle Cables?

How to Install a Water Plug?

How to Drain the Water from the Radiator?

How to Repair a Flood-Damaged Car?

Can You Drive on the Highway with a Spare Tire?

What is the function of the Jetta intake sensor?

How to Handle Vehicle Annual Inspection on Mobile Phone?

How to Make a U-Turn Over Double Solid Lines?

How to Turn Off the Continuously Flashing Hazard Lights?

What is the refund process for Shouqi Limousine & Chauffeur?