Why does a Mercedes-Benz car not move when the accelerator is pressed after starting?

1 Answers
Andres
07/30/25 10:03am
The reason why a Mercedes-Benz car does not move when the accelerator is pressed after starting is due to clutch slippage. Below are the specific details: 1. Manifestation: Clutch slippage is mainly manifested as the vehicle's speed not increasing with the rise in engine RPM during acceleration, and the engine's power not being fully transmitted to the driving wheels, resulting in weak driving force, especially noticeable when going uphill. 2. Causes: The main reasons for clutch slippage are insufficient friction of the clutch friction plate; shifting gears prematurely or disengaging gears before the clutch is fully engaged; prolonged driving in a semi-clutch state or coasting with the clutch pedal pressed; and abnormal wear of the clutch plate caused by abruptly pressing the accelerator when shifting or disengaging gears is not fully completed.
Was this review help?
16
3
Share
More Forum Discussions

Reasons for the Decrease in Tesla's Electrical System Battery Level?

Electric vehicles commonly experience this situation. It is the system's protection mechanism for the battery to ensure range. Below is detailed information about Tesla vehicles: Introduction: Tesla is an American electric vehicle and energy company that manufactures and sells electric vehicles, solar panels, and energy storage devices. Expansion: Tesla's first car product was the Roadster, launched in 2008, a two-door sports car. The second car product was the Model S, launched in 2012, a four-door all-electric luxury sports sedan. The third car product was the Model X, a luxury all-electric SUV.
18
1
Share

Can You Still Drive with the Transmission Stuck in 3rd Gear?

If the transmission is stuck in 3rd gear, you may still drive slowly. If the distance is short, you can drive to a 4S shop for repairs. For longer distances, it's best to wait for roadside assistance. Here is additional information: Check the wiring harness: There's a high chance that the wires at the electromagnetic valve harness connector have been pulled apart due to frequent engine vibrations. In rare cases, the issue might be a faulty electromagnetic valve. Being stuck in 3rd gear indicates the transmission has entered emergency mode, and the gear fault light should also be on. Internal failure: The problem could be due to a malfunction in the gearshift assembly, a fault in the transmission control module, or a defective gear position switch. Accelerator pedal operation: While pressing the clutch pedal again, quickly shift to a lower gear (these two actions should be performed simultaneously). As you press the accelerator pedal, lift the clutch pedal slightly faster.
6
5
Share

Where is the Victoria motorcycle produced?

Victoria is a German motorcycle brand. Later, it collaborated with China's Longjia Motorcycle to launch the Longjia Victoria motorcycle, which is produced in Ningbo. Therefore, Victoria's design highlights European style in every aspect. Here is some additional information: 1. Design Style: Victoria's design inspiration comes from the classic car shapes of Europe in the last century, similar in style to the existing Django and Vespa, integrating many modern technological products into the elegant retro design, capturing the essence of classic scooters. 2. Precautions: From a safety perspective, it is advisable to start with a small displacement and proceed steadily. It is recommended that beginners start with a motorcycle no larger than 250CC and upgrade only after gaining sufficient skills and experience. After all, while speed and excitement are important, safety should always be the top priority.
4
4
Share

What causes severe bouncing after installing coilover suspension?

Preload is too tight, damping is too high, and the shock absorbers lack flexibility, resulting in noticeable bouncing. Modified coilovers are generally stiffer than the original ones, leading to poor shock absorption when driving on uneven roads and causing significant up-and-down bouncing. You can adjust the tire pressure. Here are some relevant details: Adjusting the spring seat: The higher the spring seat, the stiffer the spring behaves, and vice versa. Adjusting the spring seat also changes the vehicle height proportionally (definitely not 1:1). Only when the damping coefficient matches the spring can the highest performance be achieved. Damping: More damping is not always better. Excessive damping can cause insufficient spring travel, resulting in severe bouncing of the entire vehicle. Adjusting the shock body height does not affect spring stiffness.
12
0
Share

What Causes All Snowflake and S Lights to Illuminate in an Automatic Transmission?

Low outdoor temperature or signal transmission errors can cause the snowflake light to illuminate; the S light may come on due to faults in the engine or transmission. Detailed reasons for both the snowflake and S lights illuminating in an automatic transmission vehicle include: Transmission fluid: If the quality of the transmission fluid is abnormal, it may damage the solenoid valve, causing both the snowflake and S lights to illuminate. Pressure valve and lock-up valve: If the two pressure valves and the clutch lock-up valve malfunction, or if the gear control valve fails, it can also result in both the snowflake and S lights illuminating. Outdoor temperature: The outdoor temperature display shows that the snowflake light does not illuminate above 4°C, a yellow snowflake light appears between 4°C and 0°C, and a red snowflake light appears below 0°C.
3
1
Share

What is the lifespan of the DL382 transmission?

Audi DL382 transmission lifespan has no specific standard. It features low fuel consumption and fast acceleration. The Audi DL382 primarily focuses on its transmission, which possesses strong capabilities, and the overall performance of the Audi DL382 has been optimized. Below is additional information: Transmission: It is a mechanism used to change the speed and torque from the engine, capable of fixing or changing the transmission ratio between the output and input shafts in steps, also known as a gearbox. The transmission consists of a gear transmission mechanism and a control mechanism, with some vehicles also including a power output mechanism. Most transmission mechanisms use ordinary gear transmission, while some use planetary gear transmission. Ordinary gear transmission mechanisms generally employ sliding gears and synchronizers, among others. Composition: The gearbox consists of two main parts: the gear transmission mechanism and the gear control mechanism. The primary function of the gear transmission mechanism is to alter the magnitude and direction of torque and speed; the main role of the control mechanism is to manage the transmission mechanism, enabling the change of the transmission ratio, i.e., gear shifting, to achieve speed and torque variation.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.