Why Do Cars Burn Engine Oil?

1 Answers
VanKennedy
07/30/25 1:26am
Cars burn engine oil due to natural wear and tear, dirty oil, etc. The specific reasons are as follows: Natural Wear and Tear: As the car's mileage increases, the wear between the piston and cylinder gradually intensifies. When this wear reaches a certain level, cylinder blow-by occurs, leading to oil burning. If the valve stem seals are damaged, the oil burning phenomenon becomes more pronounced. Dirty Oil: Dirty oil contains impurities that accelerate engine cylinder wear, resulting in oil burning. Additionally, using counterfeit oil or oil that does not meet the vehicle's specified grade prevents the formation of a proper oil film on the engine's friction surfaces. Severe cases may cause cylinder scoring, while milder cases lead to blow-by, both contributing to oil burning.
Was this review help?
10
3
Share
More Forum Discussions

What does setcoast mean in a car?

Car's setcoast button is actually a function key in the cruise control system. 'Set' represents setting, and 'coast' represents reduction. It is used to adjust the preset speed of the cruise control system, mainly for setting deceleration. It is generally used in conjunction with buttons like 'on' and 'res' on the steering wheel to properly configure the cruise control system. How to use the steering wheel setcoast: First, press the 'on' button on the steering wheel to activate the cruise control system. Then press 'res+' to increase the cruising speed or 'res-' (setcoast) to decrease the speed, usually by 1km/h per adjustment. After setting the desired speed, simply press the 'set' button. Note that operation buttons may vary depending on the car model, so refer to your specific controls for accurate usage. Precautions for using cruise control: Do not use cruise control in densely populated urban areas or complex road conditions. When cruise control is active, the throttle is automatically managed by the car's computer, leaving the driver unable to control it. This can be dangerous in sudden situations where immediate speed adjustment is needed. Additionally, avoid using it on winding mountain roads, as turns require greater steering force, and cruise control may lead to loss of control, causing skidding or drifting. Cruise control is best suited for highways, where road conditions are relatively stable and maintaining a constant speed is generally safe.
11
2
Share

How to Open the Hood of a Qoros 5?

Open the driver's door and locate the front hood release lever on the lower left side. Pull the release lever upward to unlatch the front hood. When the front hood pops up with a wide gap, you're ready for the next step. Finally, move the latch aside to fully open the hood. Lift the support rod and secure it into the designated slot on the hood.
7
0
Share

What are the steps to start a manual transmission car after getting in?

The steps to start a manual transmission car after getting in are: 1. Fully depress the clutch with your left foot and shift into first gear; 2. Turn on the left turn signal and honk to alert vehicles and pedestrians in front and behind; 3. Release the handbrake and gently lift the clutch with your left foot; 4. When reaching the semi-engaged state, lightly press the accelerator with your right foot; 5. After moving forward, fully release the clutch; 6. Adjust the gear according to road conditions. Precautions for starting a manual transmission car: 1. Do not release the clutch too quickly, lift it slowly; 2. Engage the engine and drive shaft before pressing the accelerator; 3. Lightly press the accelerator during semi-engagement, then release the clutch; 4. Release the handbrake before starting.
8
3
Share

What is the replacement interval for an oxygen sensor?

Oxygen sensors typically need replacement after 100,000 kilometers. Their primary function is to control vehicle exhaust emissions, effectively reducing environmental pollution caused by automobiles. The working principle of an oxygen sensor involves using a ceramic sensing element to measure the oxygen potential in a furnace or exhaust pipe. Based on chemical equilibrium principles, it calculates the corresponding oxygen concentration to monitor and control the air-fuel ratio during combustion, ensuring product quality and compliance with exhaust emission standards. The testing method for an oxygen sensor includes: 1. Disconnect the oxygen sensor plug; 2. Use a multimeter set to resistance mode to measure the resistance between pins 1 and 2 of the sensor plug; 3. A normal resistance value ranges between 4 and 40 ohms. If the resistance is outside this range, the oxygen sensor should be replaced.
11
5
Share

How to Use Mengjia Mobile Interconnection with Wuling Hongguang S?

After downloading, proceed with the installation. During installation, you need to enable the required permissions, then register an account and log in. Enable USB debugging on your phone. Go to 'Settings', select the 'About Phone' option, then turn on 'Developer Options' and enable 'USB Debugging'. Connect your phone to the central control screen using a USB cable. Once the connection is successful, you can use the corresponding functions of the Mengjia software.
18
4
Share

Why does the engine sound louder in cold weather?

The reasons why the engine sounds louder in cold weather are: 1. After the car has been parked for a long time, the engine oil flows back to the oil pan at the bottom of the engine; 2. Before the engine reaches its operating temperature, the fuel supply system cannot effectively vaporize gasoline completely due to low temperature; 3. In cold conditions, gear oil flows to the lower part of the transmission; 4. The engine mount rubber is aged or loose. The methods for engine maintenance are: 1. Regularly change the engine oil and filter; 2. Use lubricating oil of appropriate quality grade; 3. Regularly clean the radiator; 4. Regularly replace the air filter, oil filter, and fuel filter; 5. Maintain good crankcase ventilation and clean it regularly; 6. Regularly clean the fuel system.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.