Why did the car battery suddenly run out of power?

What causes water leakage behind the sunroof?

Water leakage behind the sunroof may be caused by a malfunction in the sunroof drainage system or improper closure of the sunroof glass. Sunroof drainage system malfunction: The sunroof drainage system does not rely entirely on sealing strips. After all, they are rubber components, and in heavy rainfall, some water may inevitably seep through the seals. This water then flows into specially designed drainage channels and is expelled from the vehicle through drainage pipes. Improper closure of the sunroof glass: Ensure the sunroof is tightly closed and carefully read the vehicle's user manual; clear the drainage pipes or adjust the drainage pipe connections. Maintenance of sunroof sealing strips: The sunroof sealing strips are located on the roof and are frequently exposed to wind and sunlight. Being rubber components, they tend to age relatively quickly.

5

Share

How long after the expiration of Guangzhou's energy-saving license plate can one apply for the lottery again?

Guangzhou's energy-saving license plate can be reapplied for the lottery two years after expiration. Situation after two years of lottery: If the incremental quotas obtained by individuals or units through the lottery method are invalidated due to overdue non-use, they cannot apply for incremental quotas again within 2 years from the date of quota invalidation. Introduction to car purchase lottery: The method of lottery car purchase is to first register for an appointment and queue, and then participate in the lottery uniformly. No money is required for the lottery car purchase. The computer randomly generates 10 numbers, and the lottery participant selects one number from them. Car lottery is a measure of vehicle purchase restriction, which limits the number of car licenses issued. The lottery is actually similar to drawing lots, and only those who win have the qualification to buy a car.

6

3

Share

What Happens If You Don't Release the Throttle When Shifting Gears?

If you don't release the throttle when shifting gears, the engine RPM will suddenly become very high when the clutch is depressed. When you release the clutch after shifting, the car will noticeably jerk, and it can also cause some damage to the engine and transmission. When accelerating, you can: Downshift or upshift as needed. For example, upshift when reaching 1800 RPM. To accelerate during this process, you can slightly ease off the throttle but don't release it completely—or even keep it pressed. The RPM will naturally rise when passing through neutral gear. Handling the situation: If you encounter a throttle pedal issue while driving a new car, don't panic. Firmly press the brake pedal to bring the car to a complete stop, then turn off the engine and contact for assistance.

3

1

Share

What Causes the ABS Light to Stay On?

ABS light illumination can occur in various states, each with different causes and solutions, as detailed below: State 1: ABS warning light remains constantly illuminated (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting its ability to detect wheel speed signals. This prevents the ABS control unit from determining vehicle speed or calculating wheel slip rates, consequently disabling proper brake modulation. Solution: Clean the wheel speed sensor and adjust its gap with the tone ring to restore normal function. Cause 2: Loose system wiring connections or poor ABS relay contact causing signal interference. Solution: Inspect all wiring connections and secure any loose terminals. State 2: ABS warning light intermittently illuminates but extinguishes during acceleration. Cause: Battery voltage drops below 10.5V when multiple electrical components are in use. The light extinguishes when engine RPM increases voltage. Possible low voltage supply to ABS system due to poor connections or grounding issues. Solution: Check battery specific gravity; inspect charging system; examine power supply connections (voltage relay or power contacts). State 3: ABS light stays on after engine start until ignition OFF. Cause: Poor grounding of ABS hydraulic valve body; faulty valve body electrical connections; ABS control module malfunction. Solution: Loosen and retighten valve body ground screws, clean contact surfaces if necessary; inspect connector gaps; replace ABS or ABS/ASR control module. State 4: ABS warning light activates during high-speed driving. Cause: ABS control unit detects significant speed difference between front and rear wheels; incorrect tire or wheel rim specifications. Solution: Verify proper tire and wheel rim specifications per vehicle requirements (refer to fuel filler door label). State 5: Intermittent ABS warning light activation. Cause: Improper brake light switch adjustment; internal switch contact failure. Solution: With engine running, depress brake pedal and manually push switch lever downward to reset position; replace brake light switch if necessary. Important: When the ABS warning light is illuminated, continued driving is not recommended. ABS malfunction means loss of anti-lock braking functionality. During emergency braking, wheel lock-up may cause vehicle skidding, preventing proper deceleration or trajectory control, creating significant safety hazards.

7

5

Share

What is the reason for the sudden disappearance of the engine fault light?

Engine fault light suddenly not lighting up is part of the self-check process when starting the vehicle. Introduction to the engine fault light: The engine fault light uses sensors to detect whether the exhaust emissions are normal. If the emissions exceed the standard, the engine warning light will activate. In most cases, if this light turns on and then disappears after a while, it indicates there is no major issue, and there is no need to worry too much. Vehicle startup alarm: It is possible that right after starting the vehicle, some issues caused by poor atomization in the fuel engine cylinders may trigger the engine warning. There is no need to address these issues, as the warning light will naturally turn off once the temperature rises.

1

2

Share

Why does the speed not increase when stepping on the gas pedal in second gear?

The situation where the speed does not increase when stepping on the gas pedal in second gear indicates a significant energy loss in the power transmission between the engine and the transmission. Identifying the issue with the transmission: If the engine RPM increases when stepping on the gas pedal, it means the engine's power operation is functioning correctly, but there is damage in the components transmitting power to the transmission. This situation requires distinguishing whether the engine is paired with a manual transmission or an automatic transmission. Manual transmission: In this case, the most likely causes are issues with the clutch or the transmission. The clutch acts as an intermediary in the power transmission between the engine and the transmission. If the clutch friction plates are slipping, power loss will occur.

5

Share

Why did the car battery suddenly run out of power?

What causes water leakage behind the sunroof?

How long after the expiration of Guangzhou's energy-saving license plate can one apply for the lottery again?

What Happens If You Don't Release the Throttle When Shifting Gears?

What Causes the ABS Light to Stay On?

What is the reason for the sudden disappearance of the engine fault light?

Why does the speed not increase when stepping on the gas pedal in second gear?

What happens if you drive 200 kilometers after the Audi oil light comes on?

Is the toe-in of a car larger at the front or the rear?

What Wrench is Used to Remove a Car Battery?

Why does the manual transmission jerk when accelerating in second and third gears?