Why can the Haval H9 car drive in water?

1 Answers
LeJeremiah
07/29/25 5:48pm
Haval H9 car can drive in water because of its high wading depth. Introduction to the wading depth of Haval H9: For cars, the wading depth mainly depends on the height of the car chassis, which is the ground clearance listed in the configuration sheet when buying a car. From this, it can also be seen that the higher the car chassis, the higher the wading depth. Off-road vehicles have strong wading capabilities, while the wading ability of urban SUVs needs to be slightly considered. The chassis of SUV models is relatively high, much higher than that of ordinary sedans. How to judge the level of wading depth: For ordinary sedans, the best reference value for wading depth is the radius of the car tire. At this position, it is relatively safe for the car, the engine will not be flooded, and water will not seep into the car through the chassis. Judging the wading depth by the wheels is intuitive and effective.
Was this review help?
5
2
Share
More Forum Discussions

What causes the beeping sound inside a Cruze?

The beeping sound inside a Cruze may be caused by the handbrake not being released or the seatbelt not being fastened. Here are the relevant explanations: 1. Warning indicators: After the vehicle is started and on the road, as long as a door is not properly closed, the car will sound an alarm. It will continuously emit a beeping sound and also display on the dashboard which door is not properly closed. Additionally, many modern cars come with built-in tire pressure monitoring. If the computer detects significantly low pressure in any tire, the vehicle will continue to emit beeping sounds after starting and display a warning indicator on the screen or dashboard. 2. Reminder for the driver: If the driver's seatbelt is not fastened, once the speed exceeds 5 km/h, the vehicle will sound an alarm and remind the driver via the dashboard that the seatbelt is not fastened. Therefore, the driver should carefully observe the dashboard or screen display to immediately identify the source of the alarm.
3
1
Share

What are the differences between the 2007 and 2008 Crown models?

The differences between the 2007 and 2008 Crown models lie in their curb weights: the 2007 Crown has a curb weight of 1620kg, while the 2008 Crown weighs 1635kg. Both the 2007 and 2008 Crown models share identical body dimensions: length 4855mm, width 1780mm, height 1480mm, wheelbase 2850mm, and fuel tank capacity 70l. Both models feature double-wishbone independent front suspension and multi-link independent rear suspension. They are equipped with the same 2.5L naturally aspirated engine, delivering 197PS maximum horsepower, 145kW maximum power, and 242Nm maximum torque. Both models are paired with a 6-speed automatic transmission with manual mode.
3
1
Share

What Does Engine Knock Mean?

Engine knock is an abnormal combustion phenomenon that occurs when pressure and temperature inside the engine increase, causing atomized gasoline to explode without being ignited, resulting in severe engine vibration. Vehicles are equipped with knock sensors, which serve the following purposes: 1. To measure engine vibration levels and adjust the ignition timing when engine knock occurs; 2. To function as an AC signal generator, detecting the speed and position of the crankshaft. Knock sensors consist of: a magnetic core, permanent magnets, and induction coils. The working principle of a knock sensor is: when vibration or knocking occurs, it generates a voltage peak. The greater the knocking or vibration, the higher the peak voltage produced by the knock sensor. A certain high frequency indicates knock or vibration, and knock sensors can measure frequencies in the range of 5 to 15 kHz. When the control unit receives these frequencies, the computer readjusts the ignition timing to prevent further knocking.
15
2
Share

Why Does the Engine Stall When Depressing the Clutch?

The reasons for engine stalling when depressing the clutch are: 1. Poor operation of the engine idle speed control system; 2. Dirty electronic throttle or idle speed control valve; 3. Unstable mixture control. Precautions for clutch usage include: 1. The clutch must be thoroughly cleaned before installation to remove anti-rust grease and debris; 2. The clutch can be installed coaxially or on separate shafts, but axial fixation is mandatory; 3. For wet electromagnetic clutches, lubricating oil must be added between the friction plates during operation; 4. Regarding power supply and control circuits, the clutch requires a 24V DC power supply; 5. When installing jaw-type electromagnetic clutches, ensure proper clearance between end-face teeth to prevent grinding during idle operation.
2
1
Share

What is the tutorial for replacing the air conditioning filter in Honda XRV?

Honda XRV air conditioning filter replacement tutorial is: 1. Open the glove box; 2. There is a pull rod on the left side of the glove box, press the pull rod hard to disengage it from the glove box; 3. Squeeze the glove box from both sides to the middle with your hands to remove it; 4. Remove the glove box and open the grid, then pull out the air conditioning filter for replacement. Taking the 2021 Honda XRV as an example, it is a compact SUV with body dimensions of: length 4328mm, width 1772mm, height 1610mm, wheelbase of 2610mm, fuel tank capacity of 55l, and body weight of 1225kg.
4
5
Share

What is the reason for the red triangle exclamation mark on the dashboard?

The reasons for the red triangle exclamation mark on the dashboard are: 1. Overheating of the dry dual-clutch transmission clutch; 2. Intervention or failure of the fuel cut-off system; 3. Parking sensor failure; 4. External light failure; 5. Engine oil pressure sensor failure; 6. Traction control system warning or failure. The solutions for the red triangle exclamation mark on the dashboard are: 1. Check if the dry dual-clutch transmission clutch is overheating; 2. Check if the fuel cut-off system is intervening or has a failure; 3. Check for any faults in the parking sensor; 4. Check for any faults in the external lights; 5. Check if the engine oil pressure sensor is faulty; 6. Check for any issues with the traction control system.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.