Why Can't the Car Key Be Pulled Out but Can Still Be Turned?

1 Answers
McZachary
07/25/25 9:05am
If the car key cannot be pulled out but can still be turned, you can try turning the steering wheel back and forth at a certain angle. If it still cannot be pulled out, the possible causes of this issue include the following: 1. P-lock interference: In automatic transmission vehicles, it may be due to P-lock interference. 2. Vehicle malfunction: If there is a vehicle malfunction and the P gear cannot be engaged, you can use the emergency switch on the gear lever to engage the gear. 3. Internal failure of the ignition switch: Mechanical or circuit failure inside the ignition switch prevents it from resetting. 4. The key itself: The key may be deformed or there may be foreign objects inside the ignition switch.
Was this review help?
9
3
Share
More Forum Discussions

Is it a traffic violation to make a U-turn on the sidewalk?

Making a U-turn on the sidewalk is considered a traffic violation. Once consequences occur, the harm caused is far greater than illegally crossing a solid line to make a U-turn, as the victims are pedestrians. A sidewalk refers to the part of the road separated by curbs, guardrails, or other similar facilities, specifically designated for pedestrian passage. Other situations where U-turns are prohibited are as follows: U-turns are prohibited where there is a "No U-turn" sign or a "No Left Turn" sign: If there is a sign prohibiting U-turns, then U-turns are not allowed at that intersection. The action of making a U-turn is an extension of a left turn, so if there is a sign prohibiting left turns at an intersection, U-turns are also prohibited there. U-turns are prohibited when there is no left-turn lane: Even in the leftmost lane, if there is no sign permitting left turns, U-turns are not allowed. U-turns are prohibited within the second left-turn lane line: When a vehicle is stopped in the second left-turn lane, it cannot make a U-turn. In the absence of any directional signs, vehicles can only make U-turns in the innermost left-turn lane. U-turns are prohibited on highways: Crossing the central divider to make a U-turn on a highway is illegal and will result in a fine and 12 demerit points. If you miss an exit on the highway, continue driving to the next exit to leave the highway, and do not attempt an illegal U-turn out of luck.
1
2
Share

Why Can't I Always Shift into Reverse Gear When Practicing Driving?

Here are the reasons why you can't always shift into reverse gear when practicing driving: 1. Not fully engaged in gear: The gear is not fully engaged and remains in neutral; reverse gear generally doesn't have a synchronizer. Although most gear shifts can be meshed through the gear's cutting angle, there are times when two gears clash and can't engage. In this case, simply lift the clutch slightly to let the input shaft rotate and realign the gears. 2. Handbrake not released: The handbrake is not released, and the car remains in manual braking mode, so it won't move. 3. Clutch not released: The clutch is not released and remains disengaged, so no power is being transmitted. 4. Transmission: The synchronizer in the transmission is stuck, or there are other issues. In this case, professional repair is needed.
16
4
Share

How to Solve Chain Noise Issues?

Here are the solutions for chain noise issues: 1. Mechanical components: The main causes of timing chain noise usually include lack of tension in the chain tensioner, stretched timing chain, abnormal wear of the guide chain plate, or abnormal timing sprocket. This involves replacing the faulty mechanical components—whichever part is damaged should be replaced. 2. Lubrication system failure: To prevent excessive chain wear and increased clearance, the system is equipped with an automatic chain tensioner. This tensioner operates based on oil pressure. When the lubrication system malfunctions, abnormal oil pressure can lead to excessive chain clearance and noise. Prompt inspection and repair are necessary to prevent excessive clearance and potential engine damage due to chain skipping. 3. Low oil pressure: Noise caused by low oil pressure is usually more noticeable at idle and reduces when accelerating.
4
5
Share

Is a Tire Produced Half a Year Ago Considered New?

Tires produced half a year ago are considered new. Below is an introduction about tires: 1. Introduction: Although tires are rubber products with a certain "shelf life," unlike food, they do not have an expiration date marked. In fact, it is difficult to determine the "shelf life" of tires because their lifespan is highly dependent on usage conditions, such as climate, parking environment, driving conditions, and the driver's habits, all of which can affect the tire's service life. 2. Tire Pressure: Besides the production date, tire pressure is also crucial for the tire's lifespan. Therefore, it is important to regularly check the tire pressure during daily use. The manufacturer's recommended tire pressure value can usually be found on the door frame. Improper tire pressure can accelerate tire wear and shorten the tire's service life.
11
0
Share

How to Identify the Authenticity of LLumar Car Window Film?

Here are the methods to identify the authenticity of LLumar car window film: 1. Clarity: Although car window films come in various colors, high-quality films allow clear visibility of objects beyond 6 meters at night. In contrast, inferior films produce a hazy effect. 2. Touch: High-quality films feel thick and smooth, whereas inferior ones lack sufficient toughness, being thin, brittle, and prone to wrinkling. 3. Odor: High-quality films have almost no unpleasant smell. However, inferior films contain high levels of benzene in the residual solvents of the adhesive layer, emitting a pungent odor that can be highly harmful to passengers. 4. Color: Some car films are darker in color. You can scratch the film with a fingernail or a sharp object. If the color comes off, it is likely a fake film. Genuine high-quality films are scratch-resistant and do not fade easily.
1
1
Share

What Causes Jerking in CVT Transmissions?

Here are the reasons for jerking in CVT transmissions: 1. Insufficient Lubrication: A common cause of jerking in CVT transmissions is gear-shift jerking during cold starts. Since most mainstream CVT transmissions require fluid, insufficient lubrication during cold starts can lead to poor chain connections. When the clutch engages during a cold start, it is prone to impact, causing gear-shift jerking. This issue can be avoided by warming up the car and ensuring the brake is firmly pressed during gear shifts to allow smooth clutch engagement. 2. Design and Quality Issues: Design and quality problems can also frequently cause shaking in CVT transmissions. A typical example involves a certain Japanese brand. The CVT failures in this brand are mainly due to poor torque converter design (connecting the transmission body to the engine), leading to gear-shift impacts that can occur at any speed. Additionally, subpar quality, excessive chain wear beyond normal levels, and a large amount of metal shavings accumulating in the oil pan can also cause shaking in CVT transmissions, though severe jerking is unlikely.
19
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.