Why can't the Bluetooth on Haval H6 be found?

1 Answers
MacValerie
07/29/25 6:46pm
Haval H6 Bluetooth cannot be found possibly because the Bluetooth is in an invisible state or the Bluetooth device is too far away. Bluetooth invisible state: If the car Bluetooth or mobile phone Bluetooth is in an invisible state, both parties will not be able to scan each other, and naturally, they cannot perform connection and pairing operations. Set the car Bluetooth or mobile phone Bluetooth to a discoverable state. Bluetooth device too far away: Since Bluetooth transmission has a certain distance limitation, when the mobile phone Bluetooth and car Bluetooth are too far apart, the Bluetooth device may not be found. Even if it is found, the connection may be affected due to the excessive distance.
Was this review help?
6
2
Share
More Forum Discussions

What to do if the Volkswagen CC burns engine oil severely?

If an older vehicle is experiencing excessive oil consumption, you may consider using engine oil with higher viscosity to enhance the sealing between the engine pistons and cylinder walls. If signs of oil burning are detected, it is essential to frequently check the oil dipstick and replace the engine oil and oil filter regularly as required.
1
5
Share

How to Solve Water Leakage in Volkswagen Lavida?

Check if the drainage holes of the sunroof and doors are blocked. You can find a disposable chopstick, break it, and use the tip of the chopstick to poke the drainage holes under the doors. After unclogging the drainage holes, there will be no water accumulation.
17
5
Share

How to Solve Water Leakage in Volkswagen Lavida Doors?

Check if the drainage holes of the sunroof and doors are blocked. You can find a disposable chopstick, break it, and use the tip of the chopstick to poke the drainage holes under the door. After unclogging the drainage holes, there will be no water accumulation.
5
4
Share

What is the problem when the instrument panel does not receive the EECU message?

The instrument panel not receiving the EECU message indicates that the Vehicle Control Unit (VECU) cannot receive signals from the Engine Control Unit (EECU). This situation is usually caused by loose connectors and should be addressed by a professional technician as soon as possible. Fault line detection for the instrument panel not receiving the EECU message: 1. Disconnect the boost pressure temperature sensor and turn the ignition to the ON position. 2. Measure the resistance between pin 11 (CAN-H) and pin 12 (CAN-L) of the communication diagnostic interface in the cabin as 69 ohms, then turn the ignition to the ON position. 3. Disconnect the VECUSL3 plug and measure the termination resistance between pin 6 and pin 7 as 130 ohms, and between pin 3 and pin 4 as 133 ohms, with no obvious issues found. 4. Disconnect the VECUSL3 plug and turn the ignition to the ON position. Measure the voltage to ground for pin 6 as 1.9V, pin 7 as 3V, pin 3 as 2.4V, and pin 4 as 2.4V. It is determined that the communication voltage from the EECU to the VECU is abnormal. 5. Disconnect the main power supply.
19
2
Share

How to Set Up Volkswagen Electronic Parking Brake?

Depress the brake pedal, start the ignition, then press the electronic parking brake button to release the parking brake, and shift from P gear to other gears. After entering the parking space, keep the brake pedal depressed, shift into P gear, and then press the electronic parking brake button next to the gear shift.
10
0
Share

What is the fault when the XCMG test light stays on?

test is the self-check program of the crane. The test indicator light will illuminate when the crane starts up, and the self-check should be completed within a few minutes at most. If there is a fault or issue, the corresponding indicator light will illuminate. Here is some relevant information: 1. Self-diagnosis: Fault detection refers to when the vehicle is unable to operate normally, the vehicle system determines which part has a problem and notifies the user through indicator lights or other methods. 2. Vehicle dashboard: The instruments on different vehicle dashboards vary, but generally, conventional vehicle instruments include the speedometer, tachometer, oil pressure gauge, water temperature gauge, fuel gauge, charging gauge, etc. In modern vehicles, the dashboard also requires a voltage regulator, specifically designed to stabilize the voltage of the dashboard power supply, suppress fluctuations, and ensure the accuracy of the vehicle instruments. Additionally, most instrument displays rely on sensors. The sensing device changes its resistance value based on the state changes of the monitored object and displays it through the instruments. The most prominent instrument on the dashboard is the speedometer, which indicates the vehicle's speed in km/h (kilometers per hour). The speedometer actually consists of two gauges: one is the speed indicator, and the other is the odometer.
16
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.