Why Can't I Reschedule After Missing the Subject 1 Test?

1 Answers
LaAnna
07/30/25 7:13am
After missing the test, the vehicle management office needs to input the results into the system, including the record of the missed test. This process takes time, approximately ten working days. After this period, you can reschedule the test. Additional Information: Driving Test Regulations: 1. Self-Registration: Through the internet traffic safety comprehensive service management platform, applicants can register, schedule, and pay for the test online. 2. Relaxed Physical Conditions: Individuals with monocular vision impairment can also take the driving test, provided their better eye meets the visual acuity standard of 5.0 or above on the logarithmic visual acuity chart, with a horizontal field of vision of 150 degrees. Conditions for physically disabled individuals have also been relaxed. 3. Cross-Region Application: First-time applicants for a motor vehicle driver's license in a temporary residence can apply for the corresponding vehicle class. 4. Simultaneous Scheduling: After passing the Subject 1 test, applicants can schedule either the Subject 2 test or the Subject 3 road test.
Was this review help?
9
3
Share
More Forum Discussions

What is the complete process for the motorcycle road test?

At the starting point, park and wait for about 5-10 seconds, turn on the left turn signal, observe the road conditions ahead, and then start the vehicle. After driving past the white line on the ground, stop and remain stationary. At the beginning of the test, turn your head left and right twice. Wait for about 5-10 seconds before starting. When the command for straight driving and lane changing is given, turn your head left and right twice and wait for 5 seconds. For pulling over to the side, align with the marker—first, pull the clutch, then apply both front and rear brakes simultaneously. Once the vehicle is completely stopped, honk the horn. Wait until the device announces that you have passed the test before moving the vehicle.
14
3
Share

How to Emergency Release the P Gear on a BMW 730?

In the trunk tool kit, there is a red T-shaped lever, which is the dedicated tool for emergency P gear release. Simply use a screwdriver or similar tool to push it forward, and the P gear will be released. Under the white cover on the lower left side of the dashboard, there is a red pull cord. Just pull it firmly, and the P gear will be released. Some models require direct unlocking on the transmission.
12
3
Share

How to Install Windshield Wipers for a Car?

Lift the cover on top; for some new wipers, you just need to pinch both sides and the cover will pop open by itself. Then remove the wiper arm from the wiper. After removing the old wiper, gently place the wiper arm on a towel. Be sure not to let it snap back on its own. Remember to remove the rubber protector from the new wiper. Open the cover on the new wiper, then place the U-shaped connector of the wiper arm into the wiper's slot. Insert the U-shaped connector into the slot. After installation, close the cover and gently lower the wiper into place.
4
2
Share

How to Drive a BMW X1 Automatic Transmission?

First, enter the vehicle and press the brake pedal with your right foot. After pressing the brake pedal, start the vehicle. Once the vehicle is started, you can release the brake pedal. After shifting to D (Drive) gear, release the handbrake.
14
5
Share

How to Set Up the Built-in Navigation Voice in a BMW?

You can find the voice prompt option on the navigation map interface, uncheck or cross it out, just locate and operate the speaker-like icon; If you cannot find the option to check/uncheck "Voice Prompts" on the map interface, you can try looking in the "Settings" interface; If you still cannot find the "Voice Prompts" option in the above locations, click into "Settings" and then select "Destination Guidance Settings."
1
5
Share

How to Remotely Turn on the Air Conditioning in a BMW?

The car must first have the necessary hardware support. Activate this function in the iDrive system. Press the [Lock] button on the key three times consecutively. Find the remote control interface, then press and hold the middle [START/STOP] button for about 2 seconds to start the engine. Enter the vehicle status and control button interface, locate the [Ventilate Now] button, click to remotely start the engine, and confirm.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.