Why Are the Headlights of a BMW Not Working?

1 Answers
VonNevaeh
07/30/25 8:54am
There could be several reasons why the headlights of a BMW are not working, such as a burnt-out filament or a relay malfunction. Below are the specific causes and solutions: Burnt-out Filament: If the low beam headlights are not working, it might be due to a burnt-out filament. First, check if there is power at the switch, then inspect the fuse for any abnormalities to make a judgment. The solution is to replace the bulb promptly. Relay Malfunction: Open the relay cover and check if the coil and resistor are intact. If the resistor is heating up and the contacts cannot close, press the movable contact. If the turn signal lights up at this point, it indicates a relay malfunction. The solution is to replace the component.
Was this review help?
20
0
Share
More Forum Discussions

What Does Basic Car Maintenance Include?

4S shops can divide maintenance into major maintenance and minor maintenance. Generally, minor maintenance refers to maintenance performed every 5,000 to 7,000 kilometers driven, while major maintenance refers to maintenance performed every 20,000 kilometers or more. Basic car maintenance includes the following items: 1. Replacing the fuel filter: Gasoline usually contains extremely small impurities, and the engine's fuel injectors, especially those in direct-injection engines, have higher requirements for fuel quality. Therefore, a dedicated fuel filter is needed to filter out impurities and provide cleaner fuel for the engine. 2. Replacing the ignition coil: As one of the vulnerable parts on the engine, the ignition coil is also an area that 4S shops pay close attention to during major maintenance.
2
4
Share

What causes the engine fault light to come on?

The engine fault light comes on due to deteriorated engine oil or a clogged air filter. Below are relevant details about the dashboard: Insufficient washer fluid level: This indicator shows the level of windshield washer fluid. If the fluid is nearly depleted, the light will illuminate, reminding the owner to replenish the washer fluid promptly. The light will turn off after adding the cleaning solution. Electronic throttle malfunction: This light is commonly found in Volkswagen models. During the vehicle's self-check, the EPC light will illuminate for a few seconds and then turn off. If a fault occurs, this light will stay on, indicating that immediate inspection and repair are needed. This indicator displays the operational status of the front and rear fog lights. When the fog lights are activated, both lights will illuminate—the left side in the diagram indicates the front fog light, while the right side shows the rear fog light.
20
1
Share

What Causes the Anti-Slip System Light to Illuminate?

Reasons for the anti-slip system light illuminating: 1. Accidentally pressing the ESP OFF button; 2. Loose or faulty sensor connectors; 3. Short circuit in wiring or related fuse blown; 4. Software issues causing poor signal transmission; 5. ABS pump failure. Methods to turn off the anti-slip system light: 1. Restart the engine and briefly press the ESP OFF button on the vehicle to check if ESP was accidentally turned off; 2. Visit a 4S shop for inspection, use a specialized diagnostic tool to locate the fault, and after repair, use a decoder to clear the fault code. The warning light will turn off once the ESP is confirmed to be functioning properly.
12
4
Share

What Does an Exclamation Mark on a Car Dashboard Indicate?

An exclamation mark appearing on the car dashboard can indicate five different types of issues: general faults, automatic transmission faults, braking system faults, abnormal tire pressure, and lighting faults. Below is a detailed analysis of these five scenarios: General Faults: A triangle with an exclamation mark inside indicates a general performance or component malfunction in the car. Common causes include parking sensor failure, fuel cutoff system intervention or malfunction, external light failure, or engine oil pressure sensor issues. It is recommended to visit a 4S shop for inspection to identify the source of the fault. Automatic Transmission Faults: A yellow gear symbol with an exclamation mark inside is the automatic transmission fault warning light, indicating a transmission issue or low transmission fluid level. The transmission fluid should be replaced promptly. Braking System Faults: An exclamation mark inside a circle with parentheses represents a braking system warning, typically signaling a braking system malfunction or low brake fluid level. Immediate inspection of the braking system is necessary to prevent accidents. Abnormal Tire Pressure: An exclamation mark below a horizontal line inside parentheses is the tire pressure monitoring warning light, which illuminates when the tire pressure is too low. Check the tire pressure and restore it to the normal range. Lighting Faults: A yellow bulb with an exclamation mark is the lighting fault indicator, signaling a malfunction in one of the car's lights. Solution: Visit a 4S shop for inspection as soon as possible, or perform a self-check focusing on commonly used bulbs such as turn signals, fog lights, and interior lighting to identify the problem.
12
0
Share

Can You Still Drive When the Brake System Warning Light Is On?

It is not advisable to continue driving when the brake system warning light is illuminated. Below are specific reasons for brake system malfunctions: 1. False Alarm: When driving uphill or performing emergency braking, excessive slope or fluid agitation may trigger a false alarm on the fluid level indicator. Simply replenish an appropriate amount of brake fluid. 2. Low Brake Fluid Level: Brake fluid plays a crucial role in the vehicle's braking system. When the driver presses the brake pedal, the force is transmitted by the master cylinder piston through the brake fluid to the wheel cylinders at each wheel, causing the brake pads to contact the wheels and thereby stopping the vehicle. Insufficient brake fluid is often accompanied by noticeably reduced braking power, and in severe cases, a complete loss of braking force may occur. This situation can be resolved by promptly replenishing the brake fluid.
11
0
Share

Where is the Golf tire pressure warning light reset button located?

Golf tire pressure warning light reset button is located below the left side of the steering wheel, which is the SET button. Reset method: Turn on the ignition switch, adjust the tire pressure, then press and hold the tire pressure reset button for 3 seconds. In terms of appearance, the Golf features more streamlined contours that create a sportier and more robust silhouette, with sharp angular waistlines that visually lower the vehicle's center of gravity. For the interior, the Golf maintains a traditional, simple and practical design style, with meticulous attention to detail in craftsmanship and more abundant configurations compared to the older model. Regarding the suspension, the Golf is equipped with MacPherson strut independent suspension at the front and torsion beam non-independent suspension at the rear.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.