Who is Responsible for Scratches in a Parking Lot?

1 Answers
TaliaLynn
08/29/25 3:16am
If a vehicle is scratched in a parking lot and the actual perpetrator cannot be found, the parking lot should bear the responsibility of custody. Here are the relevant details: 1. Relevant regulations: If the parked vehicle is damaged or lost due to poor management by the parking facility, the facility should bear corresponding liability for damages. 2. Scratch handling: If the vehicle is scratched while moving and the other party does not flee, follow the provisions of the "Rapid Handling Measures for Motor Vehicle Traffic Accidents." Pay attention to the surrounding traffic conditions and turn on the hazard warning lights. Quickly take photos of the accident scene from various angles, ensuring to capture multiple factors that may affect the accident determination, such as lane markings on the ground.
Was this review help?
5
5
Share
More Forum Discussions

What is the difference between clay bar waxing and polishing waxing?

The differences between clay bar waxing and polishing waxing are: 1. Different functions: Clay bar waxing can waterproof and protect against acid rain, reducing the amount of water droplets adhering to the car body. By refracting some light, it prevents the car paint from aging and fading due to high temperatures and UV rays; polishing waxing does not have these effects. 2. Different results: After clay bar waxing, there will be slight scratches; after polishing waxing, the car will look very beautiful and glossy. 3. Different operation frequencies: Clay bar waxing can be done once every half month; polishing waxing should be done once every one or two years. 4. Different purposes: Clay bar waxing involves applying car wax in a circular motion with a sponge on the car's paint surface to remove surface stains and protect the paint layer; polishing waxing uses a cloth electric wheel to rub the car's surface, aiming to treat scratches, especially more severe ones.
3
0
Share

What are the defects of the 15c4e car engine?

15c4e car engine's defect is insufficient torque in the mid-range RPM. The base 1.5T 6AT version is equipped with SAIC-GM's LFV direct-injection engine. After upgrading to China VI emission standards, its maximum power increased to 127kw, and peak torque rose to 275Nm (1750-4000 RPM). While the power level is not bad, it still falls within the standard range for small-displacement engines. Paired with a 6AT automatic transmission, the power is merely adequate. The high-end 2.0T 6-speed wet dual-clutch version features a 20L4E engine based on Buick's 2.0T direct-injection turbo technology, with a maximum power of 170kw and peak torque of 370Nm (2000-4000 RPM).
2
3
Share

Why is one training wheel higher than the other?

Training wheels are uneven because they were installed slightly off. The training wheels on a child's bicycle should be at the same height and slightly off the ground. The purpose of training wheels is to help maintain the balance of the bike. When riding, if the center of gravity shifts to the left, the left wheel will touch the ground, and if it shifts to the right, the right wheel will touch the ground, thereby maintaining balance and preventing the bike from tipping over. Precautions for installing training wheels: 1. The distance between the training wheels and the ground should not be too small or too large. If it's too small, the wheels may lift off the ground on uneven surfaces; if it's too large, the bike may tilt too much when the child is riding. 2. The protruding part of the limit clip should fit into the opening of the rear fork of the frame, and all components should be tightly connected without any gaps.
12
2
Share

What to Do When There is Fog Inside the Headlights? Is It Normal?

Fog inside the headlights is not normal. The solution is to go to a 4S shop for disassembly and repair. The headlight needs to be removed, and the lens cover should be opened to dry it. After drying, check whether there is any damage or leakage in the headlight. If no abnormalities are found, it is necessary to replace the sealing strip of the headlight rear cover and the ventilation pipe, as well as other hardware components. If there is severe water accumulation, the headlight needs to be replaced. The reasons for fog inside the headlights are: 1. Large temperature differences in winter, causing condensation inside the headlight: When the external temperature drops, the ventilation pipe will draw in humid air, causing the headlight to condense into fog. 2. Fog is likely to form after heavy rain or car washing: When washing the car, if water is sprayed directly onto the engine compartment and headlights with a high-pressure water gun, or when the vehicle wades through water, a large amount of water vapor will form on the surface, and some of the water vapor will enter the headlight through the ventilation pipe.
9
3
Share

How to reset a separated tubeless tire and steel rim?

Methods to reset a separated tubeless tire and steel rim: 1. Inspect the tire and rim; if undamaged, simply reinstall the tire onto the rim for reset. 2. Use a high-power air pump to inflate. The tubeless tire and steel rim are held together by air pressure—the more inflated, the less likely air will leak. New cars often experience air leakage due to insufficient inflation. If air leakage persists after inflation, it indicates poor sealing between the tire and rim or a small puncture. A tubeless tire rust-proof leak sealant can be used without damaging the steel rim. Tubeless tires, also known as 'low-pressure tires' or 'pneumatic tires,' feature high elasticity and wear resistance, along with excellent adhesion and heat dissipation properties.
4
4
Share

What is the solution for the interior dome light not turning off in the Envision?

The solution for the interior dome light not turning off in the Envision is: 1. If the dome light remains on after turning off the car, you can press the button to manually turn it off; 2. If you exit from a door other than the driver's door after turning off the car and then lock it, this issue may occur. The correct method is to exit from the driver's door and lock the car after turning it off, and the interior dome light will automatically turn off. The Envision has a length of 4686mm, width of 1839mm, height of 1686mm, a wheelbase of 2750mm, and a top speed of 190 km/h. It is equipped with a 7-speed dual-clutch transmission. The front track of the Envision is 1584mm, the rear track is 1588mm, the maximum torque is 250Nm, the front suspension is a MacPherson independent suspension, the rear suspension is a multi-link independent suspension, and the drive system is front-wheel drive.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.