Which Volkswagen model has a rotatable rear emblem?

How to Adjust High Beam and Low Beam on a Sedan?

How to adjust high beam and low beam on a sedan is as follows: 1. For the standard of car low beam adjustment, it generally only specifies the light intensity and beam height. The low beam should illuminate the area 25-35 meters in front of the car, and the beam height should not be too high to avoid dazzling other vehicles and affecting driving safety. 2. The car low beam can be adjusted by yourself using the knob behind the headlight assembly with tools. Park the car 10 meters away from a wall, measure the distance from the low beam to the central axis, the distance from the high beam to the central axis, and the distance from the low beam to the ground; then move to the wall and mark the corresponding positions on the wall; observe whether the light beam is offset left or right, too high or too low. If the center of the headlight beam does not align with the marked point, it indicates an offset, which can be adjusted by rotating the headlight width adjustment knob to align the center of the headlight beam with the mark on the wall. 3. Generally, the headlight width is preset at the factory, and self-adjustment is not recommended. If there is an offset, fine-tuning can be done. During adjustment, the right headlight beam can be slightly adjusted to the right, which can help see the right side of the road more clearly in low visibility conditions such as rainy or foggy days. However, it is more recommended to go to a 4S shop or repair shop for standard adjustment.

12

3

Share

How to Clean the Three-Way Catalytic Converter in a Car?

The three-way catalytic converter is an emission control device in the engine, and its proper functioning determines the engine's fuel consumption, power, and emission performance. If it becomes clogged or malfunctions, the exhaust emissions will exceed the standard. It is recommended to perform a non-dismantling cleaning, either by using the "drip method" or by adding a cleaning agent to the fuel tank. The specific steps for the "drip method" are as follows: 1. Start the engine and turn it off after the water temperature normalizes; 2. Pour the cleaning solution into a specialized device and connect the device's output to the vacuum pipe; 3. Start the engine, maintain the RPM at around 2000, open the flow control valve, and slowly drip the solution into the intake manifold for approximately 30 minutes; 4. After cleaning, keep the engine running at the same RPM for 3-5 minutes to expel any residual liquid.

14

3

Share

What brand of engine is used in the Changan CS75?

The engine of the Changan CS75 is independently developed by Changan Automobile and belongs to a domestically produced engine. The engine model of the Changan CS75 is JL473ZQ7, with a maximum horsepower of 180, a maximum power of 132kW, and a maximum torque of 300Nm. For daily maintenance of the Changan CS75 engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected according to mechanical load, with the selection standard not lower than the requirements specified by the manufacturer. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance deteriorates, which can cause various problems for the engine. To avoid malfunctions, the oil should be changed regularly according to usage conditions, and the oil level should be kept moderate. When the oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and the oil cannot pass through the filter element, it may burst the filter element or open the safety valve, allowing the oil to bypass through the bypass valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and the cylinder wall, mixing with metal powder from component wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, clogging the filter and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and the engine.

7

3

Share

How to reset the rear wheel brake caliper on a Corolla?

The rear wheel brake caliper on a Corolla can be pushed back using a specialized tool, which requires two people to cooperate—one to press and the other to twist—to reset it. If the brake caliper fails to reset, the brakes will not function properly, severely affecting driving safety. Below are the methods to repair the brake caliper: 1. Not replacing the brake fluid for a long time can cause internal rust in the brake caliper; applying grease can help. 2. Remove the guide tube, sand the two installation bolts with sandpaper, and apply grease. 3. Replace the caliper with a new one, then add new brake fluid, being careful not to overfill. 3. Finally, check if the brakes can reset normally.

10

0

Share

What engine is used in the Roewe i6?

The Roewe i6 is equipped with a new energy 1.5-liter turbocharged engine. Below are the relevant details: 1. Roewe has officially announced the powertrain information for the new i6 model, which features a three-cylinder 1.0T (officially named SGE16T) and a four-cylinder 1.5T (officially named SGE20T) engine. It also offers a 6-speed manual transmission and a 7-speed dual-clutch transmission for consumers to choose from. The Roewe i6 comes with a 10.4-inch ultra-large high-definition touch capacitive screen, supporting voice interaction, remote vehicle control, navigation, and the YunOS intelligent vehicle system. 2. The technological configuration is a major highlight of the i6, featuring exclusive identity ID login, remote vehicle control (including remote car finding, seat heating, door locking/unlocking, and air conditioning on/off). Additionally, the vehicle offers free basic services and basic data for life, unlimited iterative upgrades, smart hardware access sharing, vehicle maintenance reminders and appointments, and vehicle positioning and anti-theft tracking. In terms of performance, the combination of the 1.5T engine and the 7-speed dual-clutch transmission is more harmonious than that in the RX5, with excellent suppression of low-speed jerking, linear power output, and comfortable suspension performance.

8

3

Share

What brand of car is oshan?

oshan is the Changan Oshan X7. Introduction: Oshan has both letter badges and graphic badges. The letter badge is used for the X7, while the graphic badge is used for the Kosai series. The Changan Oshan X7 is a compact SUV under the Changan Automobile brand, featuring a MacPherson strut front suspension and a multi-link rear suspension. Dimensions: The Changan Oshan X7 has a body length, width, and height of 4705mm, 1860mm, and 1720mm respectively, with a wheelbase of 2780mm. It is powered by a 1.5T turbocharged engine, paired with a 6-speed manual transmission.

8

0

Share

Which Volkswagen model has a rotatable rear emblem?

How to Adjust High Beam and Low Beam on a Sedan?

How to Clean the Three-Way Catalytic Converter in a Car?

What brand of engine is used in the Changan CS75?

How to reset the rear wheel brake caliper on a Corolla?

What engine is used in the Roewe i6?

What brand of car is oshan?

How to Repair Trunk Dents?

How Much Horsepower Does the Toyota Corolla Have?

Can I Just Top Up the Coolant If My Car's Coolant Is Low?

What to Do About Rust on the Car Chassis?