Which Vehicles Are Exempt from Expressway Tolls?

Does the 10th-generation Accord produce more carbon deposits when using 95 octane gasoline?

According to the official vehicle user manual recommendation, the 10th-generation Accord should use 92 octane gasoline, so using 95 octane may lead to increased carbon deposits. In addition to checking the appropriate gasoline grade in the vehicle user manual, the 10th-generation Accord's fuel cap also displays this information. Typically, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a ratio between 10.0-11.5 should use 95 octane. However, with the application of new technologies, the compression ratio alone cannot determine the appropriate gasoline grade. High compression ratio engines can also be tuned to use lower octane gasoline due to other influencing factors such as ignition timing, turbocharging technology, and Atkinson cycle technology. Generally, the higher the gasoline octane rating, the higher the octane number and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If the 10th-generation Accord occasionally uses the wrong gasoline grade, simply switch back to the correct grade after consumption. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower octane gasoline, using higher octane gasoline will not cause damage, but the increased octane number may alter the fuel's ignition point, leading to delayed combustion in the engine. This results in reduced engine power and thermal efficiency, with the practical experience being poorer performance; For vehicles recommended to use higher octane gasoline, using lower octane gasoline can cause engine knocking. Due to the significantly lower octane number, the gasoline's ignition point decreases, causing premature ignition during the compression stroke. If combustion occurs before the spark plug ignites, resistance will arise during the upward stroke. This resistance makes the engine run very unstably. If the knocking is imperceptible, it only increases noise without obvious engine damage. However, noticeable knocking indicates severe engine conditions, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, and in severe cases, cylinder scoring.

13

5

Share

Where is the rearview mirror heating switch located on the Tiggo 8?

The rearview mirror heating button on the Tiggo 8 shares the same button as the rear windshield heating function. Among the physical air conditioning buttons, there is one with a small rearview mirror icon next to the front windshield button. The rearview mirror heating feature is particularly useful during rainy or snowy weather. When activated, the heater behind the mirror quickly warms the mirror surface, gradually removing rain or fog, eliminating the need for the driver to manually wipe the mirror frequently, thereby reducing driving hazards. Methods to activate the rearview mirror heating function: There are generally two ways to activate the rearview mirror heating function. One is combined with the electric rearview mirror adjustment button—simply rotate the knob to turn it on. The other is located on the air control panel—press the heating button to activate it. No manual angle adjustment is required, as there is an adjustment button on the driver's side. Principle of the rearview mirror heating function: After rotating the button, the electric heater behind the rearview mirror glass rapidly heats up to a fixed temperature within a few minutes, typically between 35-60 degrees Celsius. The heat is then distributed across the left and right rearview mirrors. Simultaneously, as the temperature rises and evaporation occurs, water droplets on the mirror surface gradually shrink, and fog slowly dissipates, effectively defogging and deicing the mirror. However, if the rainfall is particularly heavy, its effectiveness may decrease and become less noticeable. Precautions for using the rearview mirror heating function: The principle of rearview mirror heating involves embedding electric heating wires in the mirror, which consume a significant amount of power. When using this function, ensure the vehicle is running. Avoid activating the rearview mirror heating while the car is stationary to prevent draining the battery, which could leave insufficient power to start the car. Additional methods for defogging rearview mirrors include: Opening windows for air circulation: Slightly lowering both side windows creates a convection between indoor and outdoor air, reducing the temperature difference and gradually eliminating fog. Adjusting the car's air conditioning to the appropriate setting can also help defog by blowing warm air onto the mirrors.

2

0

Share

What to Do About Transmission Oil Leak in Yidong Plus?

Here are the solutions for transmission oil leak in Yidong Plus: 1. Carefully inspect and locate the source of the oil leak; 2. If the oil seal or the O-ring rubber gasket on the end cover is damaged, replace it; 3. If the leak is at the joint of the transmission case, clean the leaking area with gasoline, wait for it to dry, then roughen the surface with sandpaper, apply mixed AB adhesive to the leaking area, and wait for it to dry. Below are the reasons for transmission oil leaks: 1. Oil leak at the oil seal neck: The oil seal may be aged or deformed, the oil seal spring may have fallen off, or the oil seal may have been installed incorrectly, all of which can cause the oil seal to fail. Replace the aged or deformed oil seal, paying attention to the installation direction—the side with the spring should face the oil side. 2. Oil leak at the joint surface of the case: If the joint surface of the case is damaged, add an appropriately thicker paper gasket at the damaged area. If the leak persists, consider welding for repair; if the sealing paper gasket is damaged, replace it with an identical one; if the case cover screws are loose, tighten them promptly. 3. Oil leak at the front joint surface of the bearing: If the sealing paper gasket is damaged, replace it with an identical one promptly; if the fastening screws are loose, tighten them in a diagonal sequence, but avoid over-tightening to prevent damage to the paper gasket.

10

2

Share

What is the 0-100 km/h acceleration time of the BMW M4 CS?

According to official data, the BMW M4 CS has three models, all with a 3.0L displacement, and their 0-100 km/h acceleration times are 3.7s, 3.5s, and 3.9s respectively. Factors affecting a vehicle's 0-100 km/h acceleration time are as follows: Torque: Torque, in layman's terms, indicates how much force is available. The greater the torque, the more force is available to propel the vehicle, resulting in naturally faster acceleration. For comparison, the Audi RS4 in the same class has a maximum torque of 600 Nm and a 0-100 km/h acceleration time of 4.1 seconds. The BMW M4 CS has a torque of 650 Nm and a maximum 0-100 km/h acceleration time of 3.9 seconds. Transmission efficiency: The transmission is the medium for power transfer, inevitably involving power loss. The higher the transmission efficiency, the better the acceleration performance. Generally, the ranking of transmission efficiency is as follows: manual transmission > dry dual-clutch transmission > wet dual-clutch transmission > AT transmission > CVT transmission. The BMW M4 CS is equipped with an 8-speed automatic transmission. Power-to-weight ratio: The relationship between horsepower and vehicle weight is called the power-to-weight ratio (unit is Hp/T). The higher the power-to-weight ratio, the faster the acceleration. For comparison, the Audi RS4 in the same class has a power-to-weight ratio of 245 Hp/T and a 0-100 km/h acceleration time of 4.1 seconds. The BMW M4 CS has a power-to-weight ratio of 275 Hp/T and a maximum 0-100 km/h acceleration time of 3.9 seconds.

14

1

Share

What is the recommended tire pressure for the Envision?

The normal tire pressure range for the Buick Envision is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and decreased by 0.1 bar in summer. This data complies with the international GBT2978-2008 standard. The Buick Envision is equipped with an active tire pressure monitoring system, allowing drivers to view specific tire pressure values directly on the instrument panel. The tire pressure monitoring system automatically monitors tire pressure in real-time while driving and alerts the driver to leaks or low pressure to ensure driving safety. Generally, a tire pressure exceeding 2.8 bar is considered too high, while a pressure below 2.0 bar is too low. Hazards of overinflated tires: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, lowering driving comfort; accelerates wear on the central tread pattern, shortening tire lifespan; increases vehicle vibration, indirectly affecting other components' longevity; overstretches tire cords, reducing elasticity and increasing load during driving. Hazards of underinflated tires: Increased friction coefficient with the road surface, leading to higher fuel consumption; makes steering heavy and prone to deviation, compromising safety; excessive movement of tire parts causes abnormal heat generation; weakens cord and rubber functionality, leading to delamination or cord breakage and excessive friction with the rim, damaging the bead area and causing abnormal wear; multiplies friction with the ground, rapidly raising tire temperature, softening the tire, and drastically reducing strength. High-speed driving may result in a blowout. If the tire pressure monitoring indicator lights up (a yellow symbol with an irregular circle, no seal on top, four small spikes below, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure. The system typically alerts when pressure is below 1.8 bar or above 3.0 bar. In this case, inspect the tires and adjust the pressure. Tire pressure monitoring not reset. After inflating the tires, failing to reset the tire pressure monitoring system means it still records the previous data, causing the indicator to light up. Simply reset the system. Damaged tire pressure sensor. The sensor, installed inside the tire and connected to the inflation valve, monitors tire pressure. If damaged during driving, it triggers the tire pressure warning light. A damaged sensor must be replaced. For the Envision, a tire pressure between 2.3-2.5 bar is generally normal. A full load may require around 2.5 bar, while two passengers may find 2.3 bar sufficient. Hazards of abnormal tire pressure include: 1. Overinflation: Overstretches tire cords, causing the central tread to bulge and wear excessively; reduces contact area with the ground, lowering adhesion and increasing skidding risk and braking distance; decreases tire elasticity, making the ride harsher and reducing comfort; increases tension on the cord layers, lowering puncture resistance and raising blowout risks on rough roads. 2. Underinflation: Causes the central tread to lift off the ground, wearing the shoulder areas excessively; increases rolling resistance and fuel consumption; softens the tire, leading to excessive heat generation during high-speed driving, accelerating aging and blowout risks.

10

1

Share

What is the battery model for the BMW 3 Series car key?

The battery model is CR2032. It is a lithium manganese dioxide battery, named according to the IEC standard. The details are as follows: C- indicates a chemical battery system with lithium metal as the negative electrode and manganese dioxide as the positive electrode; R- indicates the battery shape is cylindrical, with F used for square shapes; 20 indicates the battery diameter is 20mm; 32 indicates the battery height is 3.2mm. The nominal voltage is 3.0V, the endpoint voltage is 2.0V, and the rated capacity is approximately 200mAh. CR2032 typically has a lifespan of 5 years. If the manufacturer's production level is low or quality control is poor, the lifespan can be significantly shortened. Domestic first-tier brand batteries can generally guarantee this lifespan. Under ideal conditions (sealed, room temperature, no moisture, etc.), the lifespan can extend to 8 years or even 10 years. The usage time of the car remote key battery is closely related to the frequency of use—the more frequently it is used, the shorter the battery life. If the remote key battery runs out, the mechanical key can be used to open and start the vehicle. Car remote keys use button batteries, mainly three types: CR2016, CR2025, and CR2032. For the specific model used in each vehicle, owners can refer to the battery model in the user manual for replacement. Button-type CR2016 battery: This is one of the most commonly used car remote batteries. The battery voltage is 3V, and most car key batteries are powered by 9V, so all three batteries need to be replaced each time. Examples include Honda, Toyota, Volkswagen, Mazda, etc. CR2016 specifications: battery diameter 20mm, thickness 1.6mm. Button-type CR2025 battery: Its usage rate is much lower than CR2016, but it is still used in some car keys. It is thicker than CR2016 but has a relatively higher storage capacity. CR2025 specifications: battery diameter 20mm, thickness 2.5mm. This type of battery is also commonly used in audio remotes. Button battery CR2032: It is twice as thick as CR2016. The 3V-CR2032 lithium manganese battery has a lithium-manganese dioxide structure. The positive electrode material is chemically stable manganese dioxide, the negative electrode is lithium metal, and the electrolyte is a lithium battery electrolyte. The main components of the electrolyte are dimethoxyethane, propylene carbonate, and lithium perchlorate. Its shape resembles a button, hence the name button lithium battery or lithium manganese button battery.

12

1

Share

Which Vehicles Are Exempt from Expressway Tolls?

Does the 10th-generation Accord produce more carbon deposits when using 95 octane gasoline?

Where is the rearview mirror heating switch located on the Tiggo 8?

What to Do About Transmission Oil Leak in Yidong Plus?

What is the 0-100 km/h acceleration time of the BMW M4 CS?

What is the recommended tire pressure for the Envision?

What is the battery model for the BMW 3 Series car key?

How to Repair a Dented Side Skirt on a Volkswagen Lavida?

How to Start Quickly Without Stalling in a Manual Transmission Car?

Should Cadillac Use 92 or 95 Octane Gasoline?

How to open the hood of an Audi Q3?