Which Side Should You Drive on Mountainous and Dangerous Roads?

1 Answers
LeReid
07/30/25 7:21am
When driving a motor vehicle on mountainous and dangerous roads, you should keep to the right side. Precautions for driving on mountainous and dangerous roads: 1. While driving, pay special attention to the road surface on the mountain side, and try to drive cautiously in the middle of the road or close to the mountain side. On curves, slow down, honk the horn, and keep to the right before turning, especially when going downhill. Reduce speed smoothly before turning and be prepared to stop at any time. When turning while climbing a steep slope, downshift in advance to ensure the vehicle has sufficient power and avoid shifting gears during the turn. 2. When meeting another vehicle, handle the situation in advance. Observe the road ahead and the conditions on the right side, choose a suitable meeting point, and be prepared to yield or stop. If the meeting point is close to a cliff or riverbank, stop to assess the road conditions and proceed only when it is safe. Especially during the rainy season on mountain roads, due to the narrowness of the road, do not drive too close to the edge when meeting another vehicle. Choose an appropriate spot and yield in advance.
Was this review help?
8
0
Share
More Forum Discussions

Why can't the fuel tank cap of the Passat Lingyu be opened?

Reasons why the fuel tank cap of the Passat cannot be opened include the fuel tank cap being stuck or the hinge of the fuel tank cap being rusty. Hidden functions of the fuel tank cap: The octane rating of the gasoline the car uses; a hidden drainage outlet for the car's drainage; marking the tire pressure of the car and the standard range of tire pressure. How to open the fuel tank cap: The in-car switch is currently the most common way to open the fuel tank door, which is certainly more convenient compared to using a key. The position of the in-car switch varies among different car models. Some are located on the floor to the left of the driver's seat, some on the left front door panel or the center console, marked with an icon resembling a fuel pump.
12
4
Share

How to Open the Hood of the Ford Everest?

The method to open the hood of the Ford Everest is: 1. Pull the hood release handle located at the lower left side of the driver's side dashboard inside the vehicle; 2. Push the hood lock safety hook handle, positioned in the middle of the radiator grille, upwards to disengage it, then lift the hood; 3. Secure the support rod into the hood's support rod hole. The Ford Everest has dimensions of 4892mm in length, 1862mm in width, and 1837mm in height, with a wheelbase of 2850mm. This vehicle is equipped with a 2.3T inline four-cylinder engine and a 10-speed automatic transmission, delivering a maximum power of 202 kW and a maximum torque of 455 Nm, with a front-engine, four-wheel-drive configuration.
9
5
Share

Can Anti-Slip Chains Be Used on Urban Roads?

Anti-slip chains can be used on urban roads, but only on snow and ice-covered surfaces. They are strictly prohibited on regular roads. Concept and Classification of Anti-Slip Chains: Anti-slip chains are generally made of steel or rubber and serve the function of preventing skidding. Based on their structure, anti-slip chains can be divided into two types: one is a pre-formed chain cover, and the other consists of several separate chains installed in a cross pattern. The latter is simpler and more affordable but less convenient to install compared to the former. Precautions for Using Anti-Slip Chains: For front-wheel-drive vehicles, the chains should be installed on the front two wheels, while for rear-wheel-drive vehicles, they should be installed on the rear wheels. Notably, for four-wheel-drive vehicles, anti-slip chains must be installed on all wheels. Improper installation may lead to skidding or loss of balance.
4
4
Share

What does false labeling mean?

False labeling refers to the situation where the actual engine power, battery capacity, or driving range of a car does not match the specifications claimed by the manufacturer. For example, if a manufacturer advertises a driving range of 600km but the actual range is only 400km, this constitutes false labeling. For consumers: False labeling is purely deceptive and irresponsible. Engines with false specifications are typically produced by unknown manufacturers and are not subject to legal supervision, meaning the quality and after-sales service of these engines cannot be guaranteed. The dangers of false labeling: False labeling is merely a means for unscrupulous businesses to seek exorbitant profits. Its existence not only hinders the healthy development of the automotive engine market and the establishment of domestic brands but also severely damages consumer interests.
13
4
Share

What are the reasons for the automatic transmission failure in the Haval H7?

Haval H7 automatic transmission failure reasons are as follows: Excessive transmission temperature: After high-intensity driving, it is easy for the transmission temperature to rise abnormally, causing the fault light to come on. In this case, simply stop the car and wait for the temperature to naturally decrease; Insufficient transmission fluid: When the car's transmission fluid is insufficient, the transmission fault light will come on to remind the driver to replenish it in time. Generally, transmission fluid needs to be replaced and added when the car has traveled approximately 50,000-80,000 kilometers; Transmission gear slippage: If the fault light comes on due to transmission gear slippage, it is necessary to go to a repair shop or 4S store for professional inspection.
6
5
Share

What causes the rattling noise in the Corolla's roof?

Rattling noise in the Corolla's roof is generally caused by assembly issues. Method for replacing the car roof: Roof replacement is very complex. First, all interior components of the roof section need to be removed. The original roof is then cut according to the size of the new roof to be installed. The new roof is welded onto the vehicle body, followed by reinstallation of other components to complete the replacement. Repair method for car roof: Use specialized automotive adhesive or bonding products. Apply the adhesive along the separated edges, let it dry for 3-5 minutes, then press to bond. If the center of the roof is sagging or detached, you can opt for clip repairs by selecting clips that closely match the roof color.
8
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.